Brief:
This is a boost glider that literally takes minutes t' build and isn't all that expensive.

Construction:
T' kit comes with a body tube for t' engine and pop pod recovery device (streamer), three main body pieces, matey, balsa nose cone, and clay for weightin' one fin down t' enable it t' circle around your launch site instead o' takin' off a couple miles down wind. Aye aye! Begad!

T' directions were extremely easy t' follow and t' entire kit be insanely easy t' put together. You almost didn't need t' instructions. Begad! All o' t' balsa pieces are laser cut and look very sharp. Aye aye! It's just like puttin' together a jigsaw puzzle. Aye aye! All I used t' put it together was CA glue and some markers to add some o' me own flavor. Avast, me proud beauty! Avast, me bucko, me proud beauty!

PROs are that all parts are well cut, easy instructions, and a very basic design so anyone o' any ability could piece it together in no time. There aren't any CONs other than that it is pretty delicate. Avast! Well, blow me down! I wouldn't even recommend sandin' t' balsa at all. Avast, me proud beauty!

Finishing:
NO PAINT! It adds way too much weight. Blimey! This is just a little rocket!

Construction Rating: 4 out o' 5

Flight:
Well, me bucko, before you fly it you really don't know how much clay t' use t' prevent it from takin' off down wind. Well, blow me down! Blimey! My first flight I thought was set up perfectly. Blimey! Ya scallywag! I had it balanced just like t' instructions said but it still flew at least 250 yards over a fence and into a baseball field nearby. And that be only on a 1/2A! I got it back and o' course added more weight t' t' fin. Avast, me proud beauty! T' second flight proved t' be still too light on t' clay so I added more again. While testin' it out by just throwin' it gently t' see how well it turns, ya bilge rat, it landed in t' grass and snapped just behind t' nose area which had t' be glued back together. Avast! It flew again and be much better, however, ya bilge rat, arrr, it really didn't catch the wind very well. Blimey! It actually fell into a flat spin for a good 4-5 seconds before it actually started flying. Almost like it be too light! I had really mixed feelings about this kit at this point. It got t' be way more frustrating than I thought it would be. Avast, me proud beauty!

Recovery:
T' pop pod streamer was constantly tanglin' but t' tube/nose cone was light enough t' safely tumble by itself if it had to. Ahoy! Blimey! And o' course thar be the whole glide recovery thin' too. Aye aye! Blimey! That's another job all together. Ahoy! Blimey! Avast! Blimey!

Flight Rating: 3 out o' 5

Summary:
It was nay too bad t' this point, but that's about as good as it is goin' to get. Begad! T' customer service part was absolutely downright terrible--and I don't mean from t' hobby shop I bought it from--I mean Edmonds, t' manufacturer! I ordered two o' these kits 2 weeks before Christmas in hopes o' givin' one each to me daughter and father so they could build and fly them together while we were home on vacation. Aye aye! Well, matey, both packages were missin' t' main body tube. Ahoy! How can you miss packin' such a thin' as t' body tubes in both packages? T' make a longer story shorter, shiver me timbers, matey, shiver me timbers, I didn't get t' replacement pieces until nearly March. That's right, March! T' online hobby shop I ordered it from no longer carries Edmonds supplies either. Ya scallywag! I don't think I'd waste me time with Edmonds gliders anymore anyway. Ya scallywag! Ya scallywag! They might be easy and convenient t' build, ya bilge rat, but they have absolutely zero durability. Blimey! It broke twice in t' same spot from just me tossin' it t' see if it glides. Ahoy!

Overall Rating: 2 out o' 5