Brief:
This kit originally came with a 54mm motor mount, matey, which I swapped for a 76mm motor mount for use with both commercial and experimental J, K, and L motors. T' airframe was laminated with fiberglass reinforcement and t' fins were mounted t' t' motor mount with Keelhaul®©™® reinforcements. Arrr! Due t' t' weight gain, t' 54" Rocket Rage chute that came with this kit was replaced with dual 80" chutes and a 36" drogue was added for dual deployment.

Modifications:
T' first modification I made t' t' kit be fiberglass lamination. Ya scallywag! All o' the airframe components includin' t' couplers, were laminated with one layer of 6oz fiberglass and one layer o' 2oz glass. Well, blow me down! Begad! T' 2oz be used because t' 6oz. has a rough weave which must be veiled with a finer weave t' make finishin' the rocket a much easier chore.

Next, matey, ya bilge rat, ya bilge rat, I had t' make centerin' rings that would fit a 3" motor mount into a 4" airframe. I made 5 centerin' rings for this motor mount modification usin' me bench mount drill press. Avast, me proud beauty! Begad! While I had t' drill press set up for cuttin' t' rings, me hearties, I also cut bulkheads that fit inside t' couplers as well as outside o' t' couplers.

T' fins were laminated t' t' motor mount with a heavy weave Keelhaul®©™®. T' Keelhaul®©™® went from fin tip t' fin tip across t' motor mount. Begad! One centerin' rin' was mounted aft o' t' fins and 2 were mounted together in front o' t' fins. Ahoy! Aye aye! The remainin' centerin' rings were mounted with one 1/4" from t' aft end and the other halfway back down t' mount towards t' forward centerin' rings.

Since all o' t' tubes were long, arrr, I be able t' strategically place components for optimum performance. Aye aye! Point in case: I made t' booster with the anti-zipper design, where t' coupler is mounted into t' top o' t' booster and t' bulkhead is mounted into t' outer end o' t' coupler. Avast, me proud beauty! Here the recovery attachment points are placed so your booster will not "zipper" and you create room t' put really long motors in. Ya scallywag! In essence, I could fly this rocket on some o' t' commercially available 30" long M motors.

Construction:
Rocket Dynamic Systems kits are well known for very strong airframe tubin' that has no glassine covering. Arrr! These are perfect tubes for fiberglass reinforcements due t' t' tubes ability t' soak in t' epoxy resins. Well, blow me down! Begad! T' RDS Quasar came with two 34" long and one 18" long airframe tubes. Well, blow me down! Begad! This kit was supplied with two 8" long couplers that were also glassine free. Begad! They are a little undersized, shiver me timbers, so you can laminate them also with fiberglass.

T' nose cone supplied for this kit be an R.W.W. Ahoy! Distributors, me hearties, better known as Public Enemy Rockets, nose cone. Avast! Begad! Blimey! This cone is modeled after t' PML 4" cone and is superior in quality. Ahoy! Recovery attachment points are reinforced, and thar are two 1/8" wide rings around t' shoulder o' the cone that gives it a great sealin' fit. Ya scallywag! Blimey! These rings are adjustable for fit by sandin' them.

All bulkheads and centerin' rings are made from 1/4" quality aircraft grade plywood and are laser cut. Avast! Begad! This kit came with 3 bulkheads, 2 U-bolt recovery attachment points, and 4 centerin' rings.

T' RDS Quasar has a signature look like no other 4" diameter rocket. Besides t' long airframe, shiver me timbers, this kit has enormous fin area. Avast! Blimey! This kit is supplied with 4 large 1/4" thick aircraft grade plywood fins that come pre-beveled.

This kit was also supplied with simple motor retention hardware.

Finishing:
Sanding...need I say more? 86" o' fiberglassed airframe and laminated fins equals a lot o' sandin' but t' end result was very nice. I went through many paint schemes before I settled on a purple and white with t' K-Power logo on the upper payload section. Aye aye! Begad! I also painted one fin yellow t' see what sort o' a roll rate this rocket might have.

Flight:
T' Quasar's first flight came on November 10, 2003, me hearties, on an experimental 76mm 2-grain "candy" motor designated as a J557. Arrr! This flight be short and sweet as it reached a grand total o' 863ft and deployed t' drogue. Begad! This motor was nay nearly enough t' get it up and going. Ya scallywag! Luckily t' with t' large fin area, t' rocket flew very stable and slow. Avast, me proud beauty! Ya scallywag! One nice thin' about this flight was that you could see everythin' in operation from drogue deployment t' main ejection. Well, blow me down! When I look back on t' flight, shiver me timbers, it actually very nice.

T' second flight o' t' Quasar came on July 31, 2004. This time I turned up t' Newtons and flew it on a K777 76mm experimental 3-grain "candy" motor. Avast, me proud beauty! Blimey! This motor took about 2 or 3 seconds t' come up to pressure before t' rocket lifted off o' t' pad and rocketed straight as an arrow t' 4,269ft. One noticeable difference in this flight from t' first was the roll rate. Ahoy! Blimey! On t' experimental K motor, this rocket started a very rapid spin about 1,000 feet into t' flight, which produced fin spin stabilization throughout t' rest o' t' flight. Avast, me proud beauty! Blimey! I had a little too much ejection charge in the drogue section, so all o' t' parachutes deployed at apogee.

Preppin' this rocket for flight only produces one problem: you need lots o' room for 103" of rocket. Ahoy! Arrr! As for room, thar be enough room for dual 80" main chutes in the main airframe as well as 30ft o' 1" tubular nylon shock cord. Aye aye! T' chutes were protected from t' ejection gasses with standard biodegradable roof insulation (dog barf).

Since thar be very little room for motor retention on t' Quasar centering ring, I had t' get creative and install four 4-40 threaded inserts into t' aft ring. Ahoy! Ahoy! Blimey! This form o' retention uses four 4-40 x 1" long socket head cap screws and washers t' retain t' motor by trappin' t' motors thrust ring. Well, blow me down! Blimey! Both flights have shown no damage or weakenin' o' t' retention system.

Recovery:
Since t' payload section is 34" long, I had room t' really outfit this rocket with a rugged recovery system usin' dual 80" main chutes and 30ft of 1" tubular nylon with room t' spare. Ya scallywag! T' 18" long drogue tube area has plenty o' room for 20ft o' 1" tubular nylon and a 36" drogue chute.

On me second flight o' t' Quasar, me hearties, ya bilge rat, ya bilge rat, I used 1.5 grams o' ejection charge instead o' t' 1 gram I used on t' first flight so t' mains came out at apogee. Blimey! Avast, me proud beauty! Other than that, me hearties, t' deployment system I put in this rocket works top rate.

Summary:
This rocket is a very reasonably priced kit and is a looker on t' field and in flight. Ya scallywag! Blimey! It be created usin' some o' t' best components out there. Blimey! This kit built stock is a very nice level II rocket but it just screams for the modifications that I put into it.

Flyin' it on windy days is nay recommended. T' fin area o' this rocket makes it very susceptible t' weather cocking.

This kit is made for t' experienced rocketeer in mind. There are no real instructions given, just merely hints, me hearties, shiver me timbers, like fiberglassin' t' airframe for larger motors.