Brief:
A unique kit where t' body tube has no fins but uses t' fins from three attached gliders instead. Aye aye!

Construction:
T' parts list:

• 1 nose cone
• 1 18" body tube
• 1 18mm motor tube
• 2 centerin' rings
• 1 engine hook
• 1 engine block
• 1 16" parachute, me bucko, matey, ya bilge rat, plastic
• 1 shroud line
• 1 set tape disks
• 1 elastic shock cord
• 1 Keelhaul®©™® shock cord
• 1 launch lug
• 3 pin lugs
• 1 screw eye
• 1 strip basswood
• 1 fin stock, balsa
• 3 foam gliders
• 3 decals for foam gliders
• 1 fin pattern sheet
• 1 set o' instructions

Quality instructions make this an easy kit t' build. Begad! Blimey! Motor mount assembly is standard with t' Keelhaul®©™® shock cord attached directly t' t' mount which all but ensures it will not detach even under t' harshest o' ejections.

This rocket actually has some very tiny fins on t' body tube, but they are there only t' keep t' gliders stable durin' flight. Well, blow me down! I had a little trouble ensurin' that t' "fins" were perpendicular t' each other as shown in the instructions, they tended t' want t' spread out into a "V" pattern, ya bilge rat, so take your time on this step.

Small launch lugs are used as t' mounts for t' gliders. Avast, me proud beauty! Blimey! You cut out the pins for t' gliders from t' included basswood strip. Aye aye! Blimey! Well, me bucko, blow me down! Blimey! I had t' sand me pins down just a bit so that they did nay fit quite so tightly into t' lugs because if they are too tight, t' gliders will nay deploy. Aye aye! Blimey! Avast, me proud beauty! Blimey! T' body tube gets a parachute for its recovery.

T' gliders themselves form t' fins for this rocket. Blimey! My gliders fit quite well together, shiver me timbers, but t' instruction do say you may have t' sand t' wings a bit to get a perfect triangle. Well, shiver me timbers, blow me down! T' gliders are pre-formed Styrofoam so you do not need t' trim them at all and they fly quite well left as is.

Finishing:
I did nay have any paints that I could use on Styrofoam, so I used different colored Sharpie markers t' color mine. Blimey! Ahoy! T' body o' t' rocket is quite easy to finish, especially since they really are no fins t' speak of. Ya scallywag! Blimey! Although decals were included for t' gliders, I chose nay t' use them.

Construction Rating: 5 out o' 5

Flight:
Launch day was a bit windy, so I was concerned because t' gliders caught the breeze a bit and moved around some. First flight was on a B6-4. Blimey! Blimey! Arrr! Blimey! It weather cocked a bit but be a surprisingly straight flight. Ahoy! Blimey! Ejection be close to apogee and two gliders came off while one stuck t' its mount and came down with the body tube under parachute. Avast! Blimey! Everythin' was retrieved.

I sanded a little more off t' pin on t' stuck glider. T' second flight was with a C6-5 and all three gliders detached and glided down. Avast, me proud beauty! T' C6-5 is almost too much motor as t' gliders are fairly small and became very hard to see.

Recovery:
T' gliders fly quite well. They are very light, arrr, so they are affected by winds but have a fairly steep glide angle and are easy t' recover. Begad! T' carrier comes down via parachute. No problems noted.

Flight Rating: 5 out o' 5

Summary:
There are four things t' keep track o' on this rocket for recovery! It helps to have some friends with you if you are launchin' with bigger motors. Ahoy! T' is a fun kit t' build and t' gliders are an interestin' alternative t' puttin' fins on t' body tube.

Overall Rating: 5 out o' 5