Background

T' Sizzler (#2127) offered by Estes, is a rocket with sharp looks and special features. Begad! Avast, me proud beauty! T' Sizzler is advertised by Estes has bein' 70 centimeters long, 4 centimeters in diameter, arrr, and 110 grams when finished. Begad! Recommended motors are the B4-2. Ahoy! Avast! B6-2, me bucko, C5-3, C6-3 and C6-5. Blimey! Well, blow me down! This bird is on t' larger side for B and C power, me bucko, me hearties, so I was plannin' t' investigate usin' 18 millimeter AeroTech D reloads or possibly t' 18 millimeters D motors offered by Apogee. More on this later. 

T' real reason I built this rocket was t' investigate t' unique rear deployed parachute system that it uses. T' nose cone is permanently glued to the body tube and t' motor is mounted in a long motor mount tube that is blown out t' aft o' t' rocket when t' ejection charge goes off. A 46 centimeter parachute is attached t' this motor mount and t' mount itself is attached to the rest o' t' rocket with a standard elastic shock cord. Aye aye! O' course, ya bilge rat, the rocket descends nose first instead o' tail first, but that should be easier on the balsa fins when meetin' t' ground after a flight. 

Construction

T' basic design is what I call "a rocket in a rocket". A smaller body tube carries t' motor mount tube inside the outer body tube. Avast! It is located by large but standard lookin' adapter rings. This inside body tube extends nearly t' t' nose cone and is capped at that end. T' outer body tube is slotted for "through t' wall" fin attachment, a nice feature. T' fins go through these slots and butt against the inner body tube, which makes them very strong. Ya scallywag! Aye aye! Estes is usin' "through the wall" fin mountin' on several o' their rockets. Ahoy! This feature makes accurate alignment o' t' fins quick and easy. 

Constructions is along pretty normal lines usin' typical glues and finishing materials. Arrr! I used Titebond aliphatic resin glue for all construction and Krylon white finishin' primer and enamels for painting. Ya scallywag! T' kit parts were o' high quality, me bucko, typical o' an Estes product. T' die cuttin' on t' fins be clean and accurate. Tubes and rings had no flaws. Begad! T' nose cone was a little rough with moldin' flash but cleaned right up with an Xacto knife and sandpaper. Avast! T' only flaw be that t' slots in t' outer body tube were t' narrow for t' 1.5 millimeter balsa fins. Avast! I solved this problem by usin' a sandin' block to carefully sand down t' thickness on t' fin tabs that extended through the tube until t' fit was "just right". Arrr! I simply rounded t' fin edges instead o' streamlinin' them. Ahoy! t' balsa grain be filled with Pactra Prep, a surface filler that I like. Arrr! It dries quickly, me hearties, me bucko, me bucko, sands easily and two coats are all I typically need for good results. 

I just followed t' instructions and t' rocket assembly be a breeze. Ya scallywag! The only modification that I made was t' file a small notch in t' aft motor mount rin' so that t' shock cord was nay pinched when t' motor mount was in place. I spent some time makin' sure that t' fit o' t' motor mount rings and the inner tube be just right. A little light sandin' on t' rings with 400 grit sandpaper made t' mount slide smoothin' and easily, ya bilge rat, but still stay in place with a motor loaded. 

A coat o' Krylon white finishin' primer be sprayed on and sanded smooth with 400 grit sandpaper after it dried. Avast! White Krylon be next, ya bilge rat, then maskin' and yellow Krylon on t' front 1/3 o' t' rocket. Well, blow me down! Well, blow me down! I applied t' kit decals and then used Krylon crystal clear as a top coat. Begad! Looks pretty good! 

Flight

T' first flight was on May 3, 1998 at a C.R.A.S.H. Well, blow me down! Avast! launch in Denver. Aye aye! Avast! Warm, sunny, me bucko, ya bilge rat, light breeze - a perfect flyin' day. Arrr! T' rocket was prepped per the instructions that Estes provided in t' instruction sheet. Ahoy! This flight was on a C5-3. Boost was straight and surprisingly high for a rocket o' this size and weight. Avast! Recovery deployment appeared normal and t' Sizzler descended normally on its 46 centimeter parachute. Avast! Upon recovery I discovered that t' parachute's shroud lines had tangled with t' shock cord on deployment, but I still got a fully opened parachute, lucky! Post flight inspection showed everythin' t' be OK except that t' elastic shock cord was scorched where it attaches t' the back o' t' rocket. Blimey! I am goin' t' change t' shock cord attachment by drilling a small hole at t' base o' one fin and attachin' a length o 100# rated Keelhaul®©™® shock cord and then tyin' t' present elastic shock cord t' that so that I is all inside t' rocket when packed. Avast, me proud beauty! This will keep t' elastic from being exposed t' t' hot exhaust gases. Begad! As it is, matey, ya bilge rat, t' shock cord attachment would probably fail in a few flights, me hearties, me bucko, nay good. If I build another Sizzler, I will do it this way from t' start. 

T' preppin' instructions by Estes did nay give me a clean recovery. Avast, me proud beauty! Arrr! I am goin' t' experiment with other packin' arrangements. Aye aye! I think t' problem is that t' shock cord is wound over t' top o' t' parachute. I believe it would be much better t' pack t' parachute on top o' t' shock cord. Well, this is the reason that I built this rocket in t' first place, t' learn about the problems with aft ejection. 

As I mentioned earlier, shiver me timbers, this rocket can easily handle more power. Ahoy! Avast! It would be a very stable platform for AeroTech or Apogee 18 millimeter composite motors of D power. Aye aye! Its construction is very strong and its flight manners are sweet. Begad! I will certainly be tryin' these in t' near future. 

Grades

Design: B 
Construction: A 
Flight: A 

This is a really cool lookin' rocket with a very stable and satisfying performance that is flawed only by a few details in its recovery system design and instructions. While nay for t' beginner, arrr, I would recommend this rocket to any rocketeer lookin' t' find out about aft recovery ejection.