Brief:
Very nice scale o' a NASA workhorse, me bucko, this kit can easily be a competition-level entry in either sport scale or giant sport scale. I decided t' enter it in a local giant sport scale competition, shiver me timbers, and while flight results are still pending (see below), t' static score placed this well ahead o' t' other competitors.

Construction:
All parts are very good quality. Aye aye! Well, blow me down! T' kit contains:

• 24mm motor tube/assembly
• BT-55 24" body tube
• BT-5 12" upper body tube
• Basswood fin stock
• Balsa nose cone
• Balsa transition
• Balsa bulkhead
• Heavy duty mylar chute
• Decals, weights, shiver me timbers, and trim tape

Construction starts off with t' motor mount assembly, a basic tube with pair o' centerin' rings approach. A nice plus is that this kit includes a Keelhaul®©™® cord anchored t' t' motor mount for recovery. Blimey! T' motor mount assembly is glued into t' BT-55 body tube.

Fins are cut from basswood usin' a template. Aye aye! Arrr! T' basswood was very easy to cut and is much easier t' work with than balsa when it comes t' grain filling. A couple quick applications o' Elmer's Fill 'n' Finish and they're ready t' go. Before gluin' on t' fins though, me bucko, you must mark t' tube and cut out cardstock fin supports, which are then bonded t' t' BT-55, matey, ya bilge rat, givin' this more o' an authentic look. Avast, me proud beauty! T' 4 fins are then glued t' t' fin supports. Begad! T' 4 smaller upper stage fins are attached directly t' t' BT-5 without supports.

Construction o' t' transition is one o' t' more challengin' aspects of this project. You start with a paper transition pattern, which is rolled into a truncated cone shape. Well, blow me down! Blimey! In order t' avoid a seam, I wound up cuttin' off the overlap tab, matey, and glued this t' t' inside edges o' t' ends, ("overlapping" inside t' transition). Avast! Blimey! T' result was a flawless/seamless joint. Begad! Blimey! While this is setting, shiver me timbers, a short length o' tubin' is glued t' t' top o' t' balsa bulkhead. Well, blow me down! Blimey! T' tube acts as a container for a couple o' lead sinkers used for nose weight, matey, as well as servin' as an alignment guide for t' transition shroud. Ya scallywag! Blimey! After epoxyin' in t' weights (use a generous amount o' epoxy here), matey, a centerin' rin' is attached t' t' short tubing, ya bilge rat, and then t' transition shroud slides over t' top. Aye aye! Blimey! Ahoy! Blimey! A smaller balsa transition section is then epoxied t' t' top o' t' tube/shroud, completin' t' assembly.

After attachin' t' upper body tube t' t' balsa transition, construction is virtually complete. Ya scallywag! All that's left is filletin' joints, matey, paint prep, and basic launch lugs and recovery system installation.

Overall, t' construction was fairly straightforward. Avast! Blimey! As long as you pay careful attention t' t' well-written instructions and t' illustrations, you should be fine. Well, blow me down! Blimey! Well, blow me down! Blimey! I'd rate this a skill level 3 kit though, due t' t' complexity of t' shroud & transition.

Finishing:
This has a fairly challengin' paint scheme compared t' basic modrocs, though for a scale competition kit, it was relatively easy. Ahoy! Avast! T' BT-55 and transition get a flat white finish, matey, while t' upper tube gets light gray, with silver trim. After painting, arrr, thar are some colored vinyl decals for stripes that go on and several highly detailed decals showin' manufacturer's information and other markings. Considerin' t' great quality o' t' components o' this kit and the highly detailed markin' on t' decals, I was a little disappointed that they were peel-n-stick rather than water-slide. Well, me bucko, blow me down! My competition score be dinged significantly for this.

Construction Rating: 4 out o' 5

Flight:
For t' qualified flight attempt, me bucko, I chose a D12-5. Winds had been a steady 12-15 mph throughout t' day, though around 5:00 we got a break and they dipped down below 10, ya bilge rat, so I decided t' put this beauty up. Begad! In addition t' t' basic flight, I picked up some gold glitter at a party supply store and went for mission points, callin' it radar chaff.

T' flight be perfectly straight without a trace o' spin and t' delay was just right, poppin' right at apogee. Ahoy! Blimey! At an estimated altitude o' 800 feet or so, arrr, I wasn't sure we'd be able t' see t' glitter, but it sparkled in t' sun and be a pretty cool sight. Well, blow me down! Begad! Blimey! Unfortunately, shiver me timbers, t' heavy ejection charge in the D12, me bucko, combined with t' very heavy weights in t' transition proved t' be more than t' recovery system could handle, as t' screw eye was ripped completely out o' t' balsa bulkhead despite t' fact that it be epoxied in (it actually pulled out a small plug). T' result be t' lower section driftin' a LONG way (cleared our half mile wide park), and t' upper section came down dangerously fast with all that lead and very little drag. Avast! T' upper section planted itself a good 4-6" into t' soft ground. Ahoy! DQ/sep, me hearties, though I'll probably have an opportunity t' repair and fly it again it at "bonus day"/continuation.

T' damage was fairly minor and once I complete t' contest flight, ya bilge rat, arrr, I'm lookin' at a torn/crimped body tube t' replace plus a replacement screw eye for the bulkhead.

Recovery:
Flight was excellent though t' recovery is poor. This really needs t' be a two-piece recovery. Aye aye! Given t' weight o' t' upper section, I'd be inclined to go with a nylon chute and heavy-duty Keelhaul®©™® shroud lines. Ahoy! I just don't think t' single mylar chute is goin' t' be able to hold up on this. Blimey!

Flight Rating: 3 out o' 5

Summary:
I was quite pleased with this kit. Aye aye! It be fairly easy t' build, resulted in a very competitive scale rocket, and just plain looks nice. Arrr! Avast! T' recovery system is obviously a weakness, matey, me bucko, though very easily correctable. Avast, me proud beauty! Ahoy! T' decals are another weakness and Andy at ASP mentioned that he might go water-slide in t' future on this (even offerin' me a set o' water-slides when I finish me repairs).

Overall Rating: 4 out o' 5