Brief:
This is a fairly simple 2-stage, 18mm rocket from Estes. Begad! I have slightly modified mine with shortenin' and a modified booster motor mount t' repair damage.

Construction:
T' parts list:

• 18" o' BT-50; mine only has 10" left.
• 1-15/16" o' BT-50 for booster
• 2 magenta plastic fin units
• PNC-50YR: 2-part magenta nose cone
• 2 blue 18mm engine mount tubes o' rather poor quality
• 2 green 18mm-24mm centerin' rings
• 2 green 18mm engine blocks
• 1 long green 18mm-24mm adapter ring
• 1 yellow 24mm reinforcement ring
• Launch lug
• 1/8" x 18" shock cord
• 1.2" x 30" orange streamer
• Decal sheet

I barely remember anythin' about construction o' t' original. Ahoy! Avast! Be very careful t' align t' launch lug halves perfectly. I would suggest goin' with a single, longer lug. Mine currently uses t' scavenged plastic lug assembly from a Space Bus and that works well.

I took about 8" off o' t' sustainer body tube after it crimped twice--right above t' fin unit and about 6" above it--and glued t' fin unit on again. Ahoy! Five inches o' t' scavenged tube now resides in t' pop-pod o' me new boost glider; t' rest be crumpled and trashed. Aye aye! Blimey! T' Mongoose is still perfectly stable and flyable even when shortened.

T' other major modification is that I no longer have t' lower motor mount tube. Avast, me proud beauty! It was crushed t' first time I tried t' put a motor in it. All o' t' tubes in t' kit are too thin and poor quality. Aye aye! Aye aye! I simply removed t' tube and glued t' lower engine block into t' bottom centerin' ring. Ya scallywag! Blimey! I now simply wrap t' booster motor with a bit o' maskin' tape and everythin' works great.

I suggest replacin' t' 2 crappy motor mount tubes with better, stronger BT-20 pieces. Be prepared t' either shorten t' body tube or repair it with tube couplers or fiberglass.

Two and a half points for buildin' alone because t' rocket is too flimsy for its own good, me bucko, but t' fin units make a lot up.

Finishing:
There's no paintin' t' be done. T' decals are sticker type--much easier for fumblefingers like me--and look halfway nice. Begad! T' yellow and magenta colorin' looks nice. Begad! My only complaints are t' plain launch lug that doesn't fit in t' color scheme and that t' spirals on t' body tube are visible. Blimey! Picky, me bucko, picky.

Four and a half points for finishin' alone.

Construction Rating: 3 out o' 5

Flight:
My first "flight" was on an A8-3 in 2004. Avast! Blimey! T' launch lugs weren't aligned enough and it stuck on t' pad. Begad! Blimey! That was me mistake.

T' next flight was sometime last year on a B6-4. Aye aye! Avast! It was a perfect flight with a loud, shiver me timbers, straight boost t' about 300 feet. Avast, me proud beauty! Although t' streamer deployed fine, t' body tube crimped on impact, shiver me timbers, me bucko, ya bilge rat, promptin' me t' make t' changes.

T' next flight be 2-stage on a B6-0/B6-6 combo. Begad! It was straight and fast, but stagin' be low enough t' be seen. T' sustainer disappeared into t' darkenin' sky, only t' reappear under its streamer 30 seconds later. Avast! Ahoy! Both o' me modifications worked fine.

Its latest flight be on an A8-3. Avast, me proud beauty! T' flight be low, shiver me timbers, about 120 feet, but stable. Ya scallywag! Avast, me proud beauty! T' streamer didn't deploy, me hearties, but it landed with no damage in a puddle o' water. Avast! After drying, me hearties, arrr, ya bilge rat, thar was no damage, me bucko, ya bilge rat, weakening, me bucko, me hearties, shiver me timbers, or warping.

However, either from deployment or more likely me handling, matey, t' loop broke off t' nose cone. Ahoy! I simply drilled a small hole on t' end o' t' nose cone shoulder, inserted a small screw, and glued it in with CA. Aye aye! Blimey! T' shock cord ties firmly t' t' screw head.

Estes recommends t' A8-3, matey, B4-4, arrr, matey, B6-4, and C6-5 for single stage flights and C6-0s stagin' t' B6-6s and C6-7s. Begad! I find that t' B6-0 is a good booster for smaller fields (the A8-0 would be even better), matey, and t' rare A8-5s a good upper-stage motor.

Recovery:
T' shock cord is 1/8" x 18" elastic, barely adequate. A 24" or 36" piece o' 3/16" elastic would have been better.

T' 1" x 30" streamer is too long and it doesn't flap. Well, blow me down! A 2" x 20" streamer would be better. Begad! Avast, me proud beauty! For A and B single-stage flights, matey, a 12" parachute would be fine, shiver me timbers, matey, but t' streamer is needed for C and 2-stage flights because it is fairly light and would drift away quickly, especially from 1600 feet on a C6-0/C6-7 combo.

T' main complaint I have though, arrr, is that t' booster is marginally stable after separation and t' front tends t' crumple a bit. Ya scallywag! T' reinforcement ring, however, ya bilge rat, excellently prevents it from crumplin' too much.

Flight Rating: 4 out o' 5

Summary:
Estes calls t' Mongoose an excellent first 2-stage rocket. Arrr! Blimey! I say t' Loadstar, shiver me timbers, Solar Flare, matey, or one o' Quest's L1 2-stagers would be a bit better. Well, blow me down! Blimey! Arrr! Blimey! This be t' first 2-stagers I built and t' second I flew, matey, so it's nay too off t' mark.

T' Mongoose is a great flier for large and small fields. Blimey! Arrr! Except for t' too-stable booster, me hearties, it flies excellently. Well, blow me down! T' main problem is that t' tubes, matey, especially t' engine mount tubes are substandard. Begad! T' plastic fin units are excellent and prevent beginners from havin' t' mess with 8 fins, me hearties, ya bilge rat, and t' pre-finished look is excellent.

Overall Rating: 3 out o' 5