Brief:
T' Beta be a small two stage rocket produced by Estes betwixt 1970 and 1984. Avast, me proud beauty! Ya scallywag! T' original version, matey, produced in 1970 and 1971, me bucko, me hearties, it was powered by S-series motors. Avast, me proud beauty! Begad! When production ceased on t' S motors, t' Beta be one o' a few kits whose internals were modified t' accept t' new mini or T motors. (T' Midget and t' Birdie may have been t' others.) T' Beta was t' rocket that got me started in rocketry back in t' summer o' 1977, ya bilge rat, shiver me timbers, and with t' 25th anniversary o' that first flight comin' up this July, ya bilge rat, arrr, I felt it would be a fittin' tribute t' build a clone.

Construction:

• 1 - EB-5B engine block
• 2 - BT-5T engine mount tubes 
• 4 - AR-520 adapter rings 
• 1 - BT-20AE booster body tube 
• 1 - JT-20C stage coupler 
• 1 - BT-20B upper stage body tubes 
• 1/32" basswood fin stock 
• 1 - LL-2A 18" sewin' elastic 
• 1 - screw eye 
• 1 - BNC-20N nose cone from BMS 
• 12" parachute

Followin' t' original instructions that I downloaded from JimZ, t' Beta was and is a simple, matey, almost foolproof build. Ya scallywag! I used an Estes fin alignment guide t' line up t' fins for t' first and second stages. Ahoy! Despite t' care I took in makin' sure t' stages lined up, it turns out that they do so in only one configuration. An oddity, me hearties, but far from a fatal flaw. Begad! I used basswood in place o' balsa for t' fins in t' hope that t' extra weight would be offset by t' greater strength. Begad! Aye aye! T' only thin' resemblin' a "gotcha" was t' fin pattern. Blimey! Begad! T' tracin' needs some work t' be able t' produce first and second stage fins that actually fit together as they were meant to. Aye aye! Just make sure that all o' your lines square up and you'll be okay.

Finishing:
Thinned Elmer's Fill & Finish was used in both body tube and fin finishing, and since I had substituted basswood in place o' t' balsa fins, I be able t' greatly reduce t' time I spent sandin' t' fins t' a nice, shiver me timbers, shiver me timbers, smooth, decal friendly finish. After a coat o' primer and t' requisite sanding, arrr, ya bilge rat, I sprayed t' entire model with Krylon gloss white. Decals were from JimZ and t' rocket turned out lookin' almost dead on t' picture in t' 1977 catalog. T' only difference was that I used t' A, ya bilge rat, B and C decals on both stages o' me original. Avast, me proud beauty! Ahoy! (It still isn't an exact replica o' me 1977 model. I actually bothered with sealin' and sandin' this time.)

Construction Rating: 5 out o' 5

Flight:
While I'm thrilled t' have a copy o' me first rocket in t' fleet, t' Beta in it's two-stage form is an endangered species as Estes has seen fit t' discontinue t' A10-0T engine. Avast! Ahoy! While this promises t' be a problem down t' road, arrr, it currently is o' little consequence as I took care t' buy out every pack locally. Ya scallywag! (One pack is even on t' pink card, just like it was when I be 14.)

For it's first flight I chose a 1/2A3-4T t' go along with t' A10-0T, hopin' t' keep it in sight on it's first flight. Well, blow me down! Avast, me proud beauty! This turned out t' be a fatal error on me part. Begad! While t' 1/2A3-4T is listed as an upper stage engine, me bucko, me hearties, it has a smaller nozzle openin' than t' A10-3T that I should have used. Since I had never flown me original as a two stager, me hearties, (due mainly t' 1977-level monetary concerns,) I be particularly excited with t' possibility o' t' two stage flight. Begad! It launched perfectly straight and as I watched it streak off t' pad, I was anxiously anticipatin' t' lower stage separation. Arrr! It never came. Avast! T' rocket tipped over at apogee and began screamin' back toward t' soft earth o' t' soccer field. Ahoy! For a moment I held out slim hope that t' soft ground would cushion t' impact somewhat, but t' sticky smackin' sound that it made as it buried it's forward section deep in t' mud changed me mind quickly. Avast! T' only good thin' about t' timin' o' t' lawn dart was that I hadn't yet ordered t' balsa cone from BMS, so all it took t' retrieve t' undamaged cone was long fingers. Ya scallywag! Avast, me proud beauty! I wasn't so lucky with t' body. Aye aye! It was immediately evident that t' top four inches o' t' body tube would have t' be replaced before it's next flight. Aye aye! Begad! This wasn't a hugely complicated project, however I realized that t' decals would have t' be re-ordered if I was goin' t' have t' same look as me original. Or so I thought.

I had recently bought a starter pack o' inkjet decal paper from Bel Decal. Ahoy! Since I didn't feel like waitin' through t' order and delivery process again, shiver me timbers, I decided t' attempt t' make a set o' me own on me home computer. For some unknown reason, me bucko, they didn't turn out very well. They worked, and from a distance you would be hard pressed t' notice a problem, but up close it was obvious that t' black ink had cracked and taken on an alligator skin-like finish. Blimey! After a spray o' clear t' decals worked fine, but t' whole thin' looked less than perfect. (Considerin' t' repair seam in t' body tube that I was only partially able t' hide, ya bilge rat, this isn't a huge deal.) I've since found that t' decal makin' process works well on some printers, me hearties, arrr, nay so well on others. Avast! Avast! Live and learn.

For t' second flight, matey, (a month later,) I took t' advice o' t' QUARK senior advisor and loaded t' refurbished Beta with t' preferred A10-0T/A10-3T combination. Blimey! Blimey! Avast! Blimey! This time t' rocket left t' pad at an angle and was still travelin' on this path when t' second stage lit. With t' exception o' t' angle o' t' flight path, ya bilge rat, ya bilge rat, this flight was perfect. Avast! Blimey! Aye aye! Blimey! T' booster floated back t' within 50 feet o' t' launch pad, matey, arrr, while t' sustainer recovered several hundred yards down range on it's 12" parachute. Blimey! Blimey! Arrr! Blimey! Nay exactly a textbook flight, shiver me timbers, but very entertainin' anyway.

Flight Rating: 5 out o' 5

Summary:
While t' Beta is a seldom seen rocket, it's appearance doesn't inspire much along t' way o' comments or recognition at launches. Ya scallywag! Blimey! It's a fairly vanilla 3FNC rocket with only t' fact that it is a two stager t' distinguish it, arrr, but most o' us will admit t' a soft spot for our first rocket. Avast! Blimey! With t' loss o' t' A10-0T in t' engine lineup, you're on borrowed time as far as flyin' it as a two stager. Avast, me proud beauty! Blimey! (Unless you happen t' have a stash like I do.)

Overall Rating: 5 out o' 5