Brief:
T' Centurion is another nice addition in t' Semroc Retro-Repro series o' rockets. Begad! For bein' a 4FNC rocket, me hearties, me bucko, it has some cool extras, arrr, namely t' dual chutes, ya bilge rat, ejection baffle and shape o' t' laser cut fins that lead me t' purchasing this rocket. Avast, me proud beauty! I really like t' curved portion o' t' fin at t' aft o' t' rocket.

Construction:
This kit comes with 2 sections o' body tube, shiver me timbers, 1 coupler, 2 baffle centerin' rings, 1 balsa nose cone, 1 engine tube, 1 engine thrust ring, shiver me timbers, 2 engine centerin' rings, 1 engine hook, shiver me timbers, 4 laser cut fins, 2 launch lugs, 1 elastic shock cord, ya bilge rat, 1 steel eyelet, arrr, 2 12” plastic parachute kits, 1 decal sheet, shiver me timbers, and 15 pages o' clear and detailed instructions.

This rocket is a very straightforward build. It can easily be done in one sittin' followin' t' instructions. Well, blow me down! The only "gotcha" that I experienced was in t' construction o' t' baffle. Ya scallywag! Begad! I followed t' instruction for test fittin' t' baffle into both body tubes but only one at a time. Ahoy! There was no sandin' needed so I glued one end into the body tube. Avast, me proud beauty! Arrr! When I went t' glue t' other section onto t' baffle, t' body tubes did nay line up correctly. Ya scallywag! I was able to sand it but it would have been much easier t' get straight if I could sand both o' t' centerin' rings at t' same time.

T' only other issue I had was with constructin' t' parachutes. It is tough threadin' t' shroud lines through the holes. Begad! Blimey! I suggest usin' a toothpick t' make t' holes after you have applied t' tape discs t' t' plastic instead of a straight pin.

Finishing:
I love t' look o' t' rocket in t' recommend black and white paint scheme. Avast, me proud beauty! Ya scallywag! I used diluted Elmer's Carpenters Wood Filler t' fins and nose cone. Aye aye! After a quick sanding, me bucko, I primed t' rocket with Kilz original primer. Arrr! Ahoy! After a light sanding, I applied a solid white primer. I masked t' rocket t' paint t' lower section gloss white and t' upper section gloss black. T' decal that come with t' kit are some o' t' best I have every worked with. Begad! You need t' trim the red stripe for t' fin and piece together t' stripe that goes around t' body tube. Begad! T' only other decal is the rocket name.

Construction Rating: 4 out o' 5

Flight:
I did me first launch at t' monthly MASA club launch. I loaded it with a B6-4. Since it has t' baffle I choose not put and waddin' in t' rocket. Ahoy! There was no meltin' o' t' plastic chutes so it appears that t' baffle be a success but I will use a little waddin' with t' larger motors. Begad! T' rocket went straight up and t' chutes deployed right at apogee. One o' them got tangled and did nay unfurl properly but this was nay a problem as thar was no damage sustained upon landing. Begad! Aye aye! This was a near picture perfect flight with t' rocket landin' only 20 feet from t' launch pad.

Recovery:
T' recovery system consists o' an elastic cord attached t' t' baffle system and I used default length o' t' cord. It is attached t' nose cone thought t' screw eye. Ya scallywag! T' two 12” chutes are also connected t' t' screw eye. I choose t' use swivels t' be able t' change them out when needed.

Flight Rating: 5 out o' 5

Summary:
This is a cool lookin' retro type rocket that is easy t' build. Ya scallywag! Blimey! Well, shiver me timbers, blow me down! Blimey! It is perfect for t' newer builders and offers the great extras for t' money. Arrr! Blimey! T' recommended engine selections give it t' ability t' be launch on a small or larger field. Arrr! Blimey! I am very happy with t' rocket and will definitely look for other Retro-Repro kits from Semroc.

Overall Rating: 5 out o' 5