Brief:
This almost-ready t' fly kit is a good introduction t' t' concept o' the swing-win' glider. I stumbled across one in a clearance bin at me neighborhood craft/hobby store and at $5 couldn't pass it up. Well, blow me down! Well, blow me down! With a lightweight and colorful Styrofoam body, me hearties, this looks like a nice little flyer (but mine wasn't...).

Construction:
Openin' t' box turned out t' be harder than makin' t' glider. Avast, arrr, me proud beauty! Once I got everythin' opened and unpacked, I found t' glider body, matey, ya bilge rat, t' stabilizer, shiver me timbers, some clay for weight, arrr, and a rubber band (would love t' have seen a few spares included with this).

T' box described this as a skill level 4 kit, which in me opinion is grossly overstated. Aye aye! This was a very easy build and well within t' abilities of the typical cub scout. Ya scallywag! I'd rate it more o' a skill level 1, although glider trimmin' might push it t' a 2.

T' only "assembly" required is slidin' t' stabilizer into the tail end o' t' fuselage and filletin' with white glue. Ahoy! Well, blow me down! Mine be a pretty tight fit and I wound up crackin' t' Styrofoam, matey, which was easily repaired with a bit more white glue.

T' swing-win' mechanism be a little tricky t' figure out, arrr, mainly due to the fact that it be a bit too stiff and needed t' be worked a little. During boost, me bucko, t' wings are held in t' swept-back configuration by a metal pin that slides into a notch in t' wings. Aye aye! When t' ejection charge fires, this arm is pushed forward releasin' t' wings (a rubber band supplies t' oomph).

Finishing:
Other than trimmin' t' glider, ya bilge rat, thar's nothin' t' finishin' this. Ya scallywag!

Construction Rating: 4 out o' 5

Flight:
First flight was on a C6-3. Begad! Blimey! Arrr! Blimey! Blimey! Blimey! Even goin' through t' closest slip hole, the rubber band felt pretty tight, ya bilge rat, and thar was a slight bend t' t' rocket on the pad, matey, me bucko, me hearties, as can be seen in t' photo. Well, blow me down! Blimey! Avast! Blimey! Blimey! Blimey! It took off on a not-quite-vertical path. Aye aye! Blimey! Arrr! Blimey! Blimey! Blimey! I'm not sure if this was due t' a short rod (only had a 36" rod today, ya bilge rat, matey, and the lug starts over 15 inches up) or t' design.

T' boost only got this about 75-100 feet up due t' t' roughly 45 degree trajectory. Ahoy! Durin' t' 3 second delay, t' not-quite-a-glider-yet managed to tumble about halfway back down. Avast, me proud beauty! When t' ejection charge finally blew, it did so with a vengeance, breakin' t' brittle Styrofoam fuselage in two. Blimey! Blimey! T' wings flopped out slightly, me bucko, just in time t' hit t' ground.

Overall, this be a very disappointin' flight. Aye aye! Avast, me proud beauty! If I'd gone with a longer rubber band and less tension, me hearties, ya bilge rat, it would probably have been fine. Well, blow me down! Ya scallywag! This one though, is ready for an early retirement, arrr, as even with additional gluin' and reinforcing, I don't think t' body is goin' t' weather another flight.

Recovery:
T' Styrofoam be obviously pretty flimsy (stabilizer broke on installation), so t' single rubber band is probably nay t' right size or tension for me kit.

Flight Rating: 2 out o' 5

Overall Rating: 3 out o' 5