T' Aura be me first rocket from LOC/Precision and I would consider it their entry level kit considerin' t' size, ease o' build and price. Arrr! Begad! It is a basic three-fin-and-a-nose-cone (3FNC) kit with a 29mm motor mount. 

Although t' kit comments indicate that t' "kit is recommended for those with previous model rocketry buildin' experience", matey, it is a very easy kit t' assemble. Arrr! Blimey! T' experience is required due t' limited illustrations in t' instructions and probably due t' t' 29mm motor option.

T' kit includes a plastic nose cone, a section o' body tube, shiver me timbers, 3 pre-cut plywood fins, motor mount materials, a launch lug and t' recovery system.

CONSTRUCTION:

T' kit comes in a plastic bag with an insert displayin' a picture o' t' Aura and t' specifications. Avast! On t' back o' this 4x11" insert are t' instructions. Begad! There are only two small illustrations. Ya scallywag! One showin' t' aft view and another cut-away showin' t' side view motor mount and fin alignment. Aye aye! T' instructions are straight forward and in a logical order allowin' t' builder t' assemble this straight-forward 3FNC rocket.

For ease o' assembly and alignment, t' fin lines and launch lug lines are pre-drawn on t' body tube. Arrr! A nice touch. Begad! touch. Blimey! This and t' simplicity o' t' rocket make it go together quickly. LOC recommends usin' epoxy (6 or 20 minute) and I used 15 minute.

T' recovery system is assembled from its own set o' instructions. Blimey! Ahoy! It consists o' a length o' braided nylon cord which is knotted at both ends, and knotted with a 1" loop in t' center. Begad! Ahoy! T' two knotted ends are taped t' t' inside o' t' body tube with t' knots on t' far side o' t' tape. Well, blow me down! Begad! Then it is coated with epoxy t' completely cover t' tape and t' knots. T' top o' t' nylon with t' 1" loop sticks out o' t' top o' t' rocket and is used t' tie t' elastic shock-cord to.

T' motor mount consists o' a 29mm tube and two centerin' rings. Begad! T' kit relies on friction fit for motor retention. Ahoy! Avast, me proud beauty! retention. Well, blow me down! I added a piece o' sprin' steel (from an old windshield wiper blade) t' make a retention hook just like an Estes kit.

Finishin' was also quick, arrr, by choice, ya bilge rat, since it was two days before NARAM-40 and this rocket be goin' along. Avast, me proud beauty! I used Plasti-Kote primer for sealin' and filling. Avast! I then painted t' entire rocket with some left-over red paint, arrr, then masked and added silver paint.  I lastly hit it with clear coat. Well, blow me down! Avast, me proud beauty! Aura does nay come with any decals so t' finish is entirely up t' you.

Overall, for CONSTRUCTION I would rate this kit 3 points.It is easy t' build and therefore similar t' many other 3FNC rockets. Well, blow me down! T' instructions were clear and t' addition o' t' shock-cord instructions ensure a successful attachment. Ya scallywag! Begad! It would be nice t' see a decal with t' name o' t' rocket and a positive motor retention system.

FLIGHT/RECOVERY:

T' Aura is a bit deceptive. Begad! Avast, shiver me timbers, me proud beauty! Blimey! Its size and looks may make observers think it is an Estes-type kit weighin' in at 2 - 3 ounces. Ya scallywag! Blimey! However, me bucko, with t' motor this kit weighs in around 12 ounces.

T' Aura was launched at NARAM-40, as planned, on an EconoJet F20-7. Arrr! Out o' sight flight, with simulation indicatin' greater than 3800 feet. Well, blow me down! It came down very fast as t' nylon streamer be spinnin' and wrappin' itself up. Avast! It landed only 50 feet from t' pad it was launch from. Ya scallywag! Blimey! Upon inspection, arrr, one fin had broken completely off takin' all o' t' epoxy bonded areas with it.

Later I tried usin' t' streamer from t' Aura on an Aerotech Mustang, only t' find t' same type o' rollin' and tanglin' on its way down. Avast! Maybe it be all t' humidity, ya bilge rat, ya bilge rat, but t' streamer did nay seem effective.

T' fin comin' off may be somethin' t' watch out for, ya bilge rat, because I have read several posts on RMR regardin' t' Aura indicatin' t' same thing. Begad! Well, shiver me timbers, blow me down! I think usin' t' technique o' pin holes along t' alignment line would be recommended. I use a variation t' this technique by usin' a hobby knife t' cut 1/4" slits across and perpendicular t' t' alignment line, spacin' them about 1/4" apart. This allows t' epoxy t' flow into t' body tube and gives it better hold. This be done when reattachin' t' fin.

After replacin' t' fin, I flew t' Aura on an Aerotech RMS E23-5T. Avast, me proud beauty! Begad! Simulation indicates that it should fly t' about 1550 feet. Begad! It was a beautiful launch and very straight flight. Avast! Watchin' it arc and start t' scream toward t' earth be nay expected though. Arrr! though. Avast! Neither be it slammin' into t' ground somewhere out o' sight and nay t' be found. Total loss included t' $20 rocket, t' $35 casing, t' $14 parachute (I should have had that streamer in there) and t' time t' get this rocket ready t' fly.

T' meanin' o' Aura is:

                 1.a distinctive and pervasive quality or 
                       character; air; atmosphere: an aura of 
                       respectability.
                  2.a light or radiance claimed t' emanate 
                       from t' body and t' be visible to 
                       certain individuals with psychic or 
                       spiritual powers.
                  3.a sensation, shiver me timbers, as o' a glowin' light or an 
                       aroma, me hearties, shiver me timbers, precedin' an attack o' migraine 
                       or epilepsy.

I think t' 3rd definition be appropriate considerin' t' migraine that ensued after realizin' t' "cost" o' that flight. Avast, me proud beauty! O' course it was nay a rocket design or kit issue.

For FLIGHT/RECOVERY, me hearties, I would rate this kit 3 points.T' streamer seems t' be t' main issue and because RMR postings indicated experiences o' losin' a fin and then it happened t' me, thar be probably reason t' consider its recovery system as t' reason. Ya scallywag! Also, motor retention would be a bonus.

Overall, ya bilge rat, this kit is easy t' build and is a nice flyer which can give very high altitudes. Begad! Consideration on fin attachment and streamer usage will need t' be taken by t' modeler. Avast! I give t' kit an OVERALL ratin' o' 3 point