Brief:
I bought this t' use up some 24mm engines. Aye aye! Plus, I couldn't resist t' idea o' a 6' rocket so bought it as a novelty item. Ya scallywag! Arrr! I later found out a second review was requested, me hearties, ya bilge rat, ya bilge rat, so here we go...

This skill level 2 rocket tops out at around 6 1/2 feet. Avast! Blimey! Blimey! Blimey! As mentioned in t' previous review, thar are some things t' consider that aren't necessarily in t' instructions. Arrr! Blimey! Overall, arrr, it's a fairly straightforward 4FNC rocket. Quality be an issue with some o' t' components, me bucko, ya bilge rat, but nothin' that required a significant workaround.

Construction:
T' components were packaged like most other rockets: a sturdy plastic bag with t' glossy freeze-frame action-shot picture on t' front. Begad! Nothin' be missing. Begad! T' kit included:

• 4 body tubes
• 3 couplers
• nose cone
• balsa sheet with pre-cut fins
• card stock with fin tabs
• recovery kit (shock cord, me hearties, parachute, shiver me timbers, shiver me timbers, me bucko, etc)
• engine mount (tube, arrr, me hearties, centerin' rings, block, motor hook, me bucko, etc.)

T' body tubes were sturdy and t' fins were thicker balsa than typical. Blimey! Durin' a dry-fit I noticed that everythin' had such a loose fit that it wouldn't stay together.

T' shock cord is a piece o' elastic--not very heat-friendly but designed t' be over 6 feet from t' ejection charge so it's probably OK. Avast, me proud beauty! T' nose cone be symmetrical, me hearties, shiver me timbers, arrr, but be "fuzzy" and required sandin' and sealing.

I found t' instructions easy t' follow but some were written in such a way that could be confusing. Well, matey, blow me down! Every step had hand-sketched pictures. T' procedure was fairly straightforward: engine mount, fins, couplers, insert engine mount, parachute, paint.

In some places I went a little out o' order. Avast! For example, I prefer t' insert t' engine mount into t' body tube prior t' attachin' t' fins. Arrr!

Because o' a very loose fit, me bucko, me hearties, I tried "buildin' up" t' centerin' rings with glue, shiver me timbers, but this didn't help. T' instructions called for applyin' glue t' t' centerin' rings prior t' installin' them, but I chose t' put epoxy inside t' body tube at t' appropriate locations. Avast, me proud beauty! I put epoxy on forward rin' location first, installed t' motor mount halfway, ya bilge rat, then put epoxy at t' aft rin' location.

One o' t' pictures shows a centerin' rin' in comparison t' t' body tube. Avast! Blimey! T' gap was easily 1/16th o' an inch.

T' only "gotcha" involved paper tabs/laminates that are attached t' t' root edge o' t' fins prior t' assembly. Well, blow me down! I be initially confused by t' instructions, but after a few re-reads they made sense. Ahoy! Ahoy! Even so, shiver me timbers, matey, I bagged t' whole idea o' t' tabs/laminates and used glue t' tack t' fins on and made epoxy fillets after assembly.

My concerns about t' couplers bein' so loose abated when I glued t' tubes together. Avast, me proud beauty! They seemed t' stick just fine. Ya scallywag!

Early on I decided t' change t' design. Instead o' bein' one long rocket with ejection occurrin' at t' nose cone, matey, I chose t' make it separate in t' middle t' make handlin' easier. Arrr! Aye aye! This required changin' t' location o' the shock cord. Avast! Avast, me proud beauty! T' elastic wasn't designed t' be so close t' t' engine, but it's still 3' from it so it should be OK.

Finishing:
Finishin' such a big rocket proved t' be a little tricky because I don't have paintin' stands, me hearties, etc. Begad! Ahoy! I found that my saw horses were leavin' marks. Aye aye! Avast, me proud beauty! T' rocket is too long t' hold it with a stick or somethin' put in t' aft end.

I already attached t' shock cord, me hearties, which be an oversight on me part: 6 feet is a long way t' reach if I'm holdin' it by t' aft end. Well, ya bilge rat, blow me down! I ended up paintin' one half at a time even though t' shock cord made this quite awkward.

If I were t' do this rocket again, I would wait t' attach t' shock cord until paintin' be completed.

I used bright yellow t' help it stand out. Begad! Blimey! I usually don't apply t' decals (my son usually picks the colors/scheme and decals rarely look OK), shiver me timbers, but did this time. Begad! No problems. Arrr! Blimey!

In t' "fleet photo", me bucko, t' Six-Footer clearly stands out. For comparison, me hearties, t' fence is nearly 4 feet high. Ya scallywag!

I gave construction only a 3 1/2 because I felt t' components were too loose, and some o' t' instructions required a second readin' (though this is a Level 2 rocket, me bucko, so presumably it's nay t' builder's first rocket and likely t' directions aren't entirely necessary).

I think it would be easier t' finish if t' builder kept t' rocket in two halves until after it's painted then finish assembly (either as one large rocket or two 3' sections).

Construction Rating: 3 out o' 5

Flight:
Prep is straightforward and easy due t' t' diameter o' t' body: 3-4 pieces o' wadding, shiver me timbers, parachute, ya bilge rat, engine, arrr, and it's done. Avast! It comes with an engine clip for retention. Aye aye! I will likely purchase a piece o' Nomex® to use instead o' t' wadding.

T' rocket is designed for D12 engines. It could probably handle more power ("E" engine) if t' builder is confident o' t' strength o' assembly.

This is a fun rocket t' fly. I'm enjoyin' it as much as some o' me others. Avast! For me, ya bilge rat, still bein' a new BAR, arrr, me bucko, sending a rocket this tall t' around 1000 feet under t' power o' a controlled explosive is a lot o' fun. Ahoy! When it's on my launch stand, t' nosecone is well over 8 feet high, matey, which looks very impressive on t' field. Blimey! Also, due t' it's weight, t' lift off is a little slow at first then rapidly picks up momentum. Arrr! This creates a rather large puff of smoke at lift-off.

T' flights have been straight and have had no issues...until t' third or fourth time I used it, me hearties, I didn't pack the waddin' correctly and melted t' chute. Ya scallywag! It came down pretty fast with t' shock cord makin' t' 2 halves tumble so violently I couldn't catch it. T' body has some "compression damage" above t' engine mount. I think this can easily be fixed by cuttin' it open and insertin' a coupler at that location t' reinforce it. Arrr!

Recovery:
T' included parachute is huge, and t' rocket drifts a bit. Blimey! Blimey! I've been flyin' this with a smaller parachute than it came with. Ahoy! Blimey! Begad! Blimey! I made pretty strong fillets with JB Weld and have had no problems with t' faster descent until the parachute melted a bit.

I don't think I'm a fan o' an all-elastic shock cord system, but it makes sense if it's built in two 3' sections. I'd guess that as t' halves come apart durin' ejection, they have a good amount o' inertia and t' elastic prevents zippering.

As I'm writin' this, me bucko, I thought an alternative would be t' model this rocket after t' Quest "Super Bird" and have it come down as two halves.

Flight Rating: 4 out o' 5

Summary:
I like this rocket, and if somethin' happened t' it, me bucko, shiver me timbers, I'd likely purchase it (or a similar one) again. Avast, me proud beauty! Avast, me bucko, me proud beauty! There are only a few things I'd change about this rocket. Blimey! I wish t' couplers had a tighter fit, me hearties, arrr, and I'd recommend assemblin' it so it is in two 3' sections. Avast! If buildin' this in 2 parts, I recommend waitin' t' attach t' shock cord until after it's painted. Ya scallywag! Blimey! If you want it as one large rocket, ya bilge rat, arrr, I'd assemble it in 2 halves, me hearties, paint it, me hearties, me bucko, then glue t' halves together. Arrr! The instructions have some quirks (what's up with those cardstock tabs?) but for t' most part are easy enough t' follow. Begad!