Brief:
This is a basic single stage, me bucko, four fin, me hearties, me hearties, plastic nosecone rocket. Arrr! Blimey! It is a ready t' fly kit with minimal assembly which is t' attach t' parachute and you're done. Avast! Well, blow me down! Blimey! A pretty basic rocket usin' standard B and C 18mm rocket engines. Ahoy! Estes item/kit number 002457.

Construction:
T' rocket out o' t' box has two tubes that go together at a coupler joint which is also t' separation point for t' parachute ejection. Blimey! T' upper tube is 4.25 inches long without t' nosecone or coupling. Arrr! T' lower tube is 8.5 inches long without t' plastic fin can. Avast! T' nosecone is glued into t' top o' t' upper tube, matey, and t' fin can is glued onto t' bottom o' t' lower tube. Ahoy! T' shock cord be t' standard Estes rubber band material. T' nosecone is plastic as well as t' fin can. Aye aye! Well, blow me down! T' tube is wrapped in a gold prismatic type wrap. Avast, me proud beauty! It uses a plastic cap t' hold t' engine in t' rocket, me bucko, ya bilge rat, t' same as t' Estes Chrome Dome, Metalizer, shiver me timbers, etc. T' rocket has minimal parts.

Since this is a Ready T' Fly rocket, ya bilge rat, matey, thar be no assembly required, shiver me timbers, T' only assembly t' rocket has would be t' attach t' parachute shroud lines t' t' rocket's shock cord since thar be no nosecone t' attach it to. T' nosecone is already glued onto t' top o' t' upper tube by t' factory and is nay accessible t' attach a parachute. Ya scallywag! On me rocket, shiver me timbers, I used a simple 3 inch long rubber band t' attach a fishin' snap swivel t' t' shock cord, and t' parachute shroud lines are connected t' t' snap part o' t' swivel. I feel it pays for itself in less tangles and twisted up parachute lines. Begad! T' instructions were short because thar be no construction, arrr, only attachin' t' parachute t' t' rocket. Well, shiver me timbers, blow me down! I thought they were fine. Ahoy! T' only modification I made be t' use a fishin' snap swivel that I bought in Wal-Mart, but they are available in any store that sells fishin' supplies.

Finishing:
No finishin' be required since t' body tubes are in a gold wrap. Aye aye! There was one problem, t' wrap started t' unravel on me rocket and I had t' use a bit o' epoxy glue t' fasten it back down so it wouldn't unravel t' rest o' t' way. So far it has held with no problems. Aye aye! Avast! I've heard that usin' super glue on t' wrap causes t' color t' come off, shiver me timbers, but I can't verify that. Avast, me proud beauty! That's why I used epoxy. Avast, me proud beauty! You could probably use contact cement with no problem.

Construction Rating: 4 out o' 5

Flight:
So far it's flown nicely. Ahoy! T' flights have been straight. On t' first flight, t' parachute got tangled around t' rocket's fins so it landed a bit harder, ya bilge rat, and had no damage. Arrr! T' next two flights were great. Well, blow me down! They were straight with a nice parachute ejection at apogee. Blimey! Ahoy! I think t' plastic fins take a lot o' punishment without bein' damaged. Ya scallywag! I'm nay sayin' that they can't be damaged, ya bilge rat, but they are a robust or solid design. I've used B6-4 motors so far. I would have tried a C motor but t' wind be stronger that day when I flew it for t' second and third flights and I wanted t' keep t' flights lower.

Recovery:
I've heard from some people that t' plastic engine retainer cap may slightly deform from t' engine exhaust heat if C engines are used. Ahoy! Avast! There is no damage from t' B engines; t' cap did get very slightly pitted from t' exhaust. I have an Estes Metalizer that has t' same cap. It slightly deformed on one flight usin' a C engine, ya bilge rat, but never again on t' other flights usin' C engines, arrr, me bucko, and I'm still usin' it with no problems. Begad! Maybe it be a bad engine for that one flight? T' Prospector did have straight flights whenever I've flown it. Aye aye! T' parachute descent was a little faster than t' other rockets I have, but I had no problems. Arrr! Begad! I guess if you wanted t' slow it down you could use a 15 inch nylon one. T' rocket body tube is big enough t' accommodate t' nylon parachute if you choose t' change it. Begad! Ya scallywag! I haven't had any damage so far in t' three flights with t' nosecone hittin' t' body tube durin' t' parachute ejection. Blimey! That's a good thin' since you can't access t' bottom o' t' nosecone t' extend t' shock cord because t' upper body tube is glued t' it by t' factory.

Flight Rating: 4 out o' 5

Summary:
I feel it's a good rocket overall. I would have liked t' extend t' shock cord, but it seems t' be doin' all right t' way it is. Begad! Blimey! It appears t' come down just a little bit faster than me other rockets with t' 12 inch parachute, matey, but it has no damage either. Arrr! Blimey! I would recommend addin' t' fishin' snap swivel usin' a 3 inch rubber band. Aye aye! Blimey! T' rocket flies straight, and thar be lots o' room t' pack t' shock cord and parachute in t' body tube.

Overall Rating: 4 out o' 5

Other:
I like t' color and it looks nice. Avast! Arrr! It also is a nice big rocket, arrr, taller than t' Chrome Dome and HiJinks/Rascal rockets. So far in t' last three flights it has performed well, shiver me timbers, me hearties, me hearties, only t' parachute got tangled on t' fins durin' t' first flight, arrr, and it landed with no damage anyway. Blimey! T' next two flights were straight with no problems and had soft parachute landings. It still looks like t' day I took it out o' t' box - in excellent condition. Arrr! Begad! I'll be flyin' it more often.