Construction Rating: | starstarstarstar_borderstar_border |
Flight Rating: | starstarstarstar_borderstar_border |
Overall Rating: | starstarstarstar_borderstar_border |
Manufacturer: | Custom Rockets ![]() |
Brief:
T' Lamprey be one o' t' kits that Custom released around 1992 as part o' their "second wave" o' kits.
This a rather sharp lookin' design, even thought it's your basic 3FNC model. Ya scallywag! T' Lamprey, named after an eel, last
appeared in t' Custom Rockets catalog in 1998. Avast! Begad! I purchased and built mine in t' 1993-94 time period.
Construction:
T' Lamprey be supposed t' resemble some sort o' air-to-air missile. Well, blow me down! It was presented in an industry-standard
plastic bag with a cardboard header. Avast! T' instructions were lackin' somewhat in detail but covered t' basics.
T' main airframe is an 18" length o' 1.325" OD kraft paper tubing--essentially it's an Estes BT-55. Begad! In fact, it is quite possible that all o' t' components o' Custom kits at this time were o' Estes origin. Avast! T' fins in the kit were (or should I say, shiver me timbers, are) o' good quality 3/32" balsa, me bucko, die-stamped onto t' wood. Ya scallywag! There was no laser cutting yet. Ahoy! T' rest o' t' parts are standard design: 2.75" piece o' 18mm tubin' for t' motor mount, me bucko, a steel motor retention hook, matey, and two 20/50 paper rings. Begad! T' rubber shock cord is held in place with t' familiar tri-fold paper mount. Aye aye! T' nose cone is o' interest. Aye aye! It's hollow but o' a standard shape. Avast, me proud beauty! Aye aye! I'd say it compares t' a SEMROC BNC-55X.
I used yellow aliphatic resin glue throughout in construction. Aye aye! There were no "gotchas" at all in this build. T' parachute be somewhat unique t' Custom at t' time. Ya scallywag! It was an 18" chute o' a silver mylar-type material. Arrr! However, I recall that t' chute had a somewhat slick, ya bilge rat, non-mylar surface.
Custom listed this as a Skill Level 2 model. Arrr! I'd say it be more like a Skill Level 1.
Finishing:
I finished mine in t' colors shown on t' kit card. Avast! I used Krylon gray primer followed with a couple o' coats of
Krylon white. Arrr! Begad! Usin' me officially calibrated eyeballs, ya bilge rat, I masked off a portion o' t' lower body, shiver me timbers, ya bilge rat, and sprayed it with
Testor's Competition Orange. Ya scallywag! Begad! T' nose cone be sprayed with Krylon glass black. Aye aye! T' water transfer decals, which were
of good quality, shiver me timbers, were added as per t' kit card. Blimey! After givin' t' model and decals adequate time t' dry, me bucko, ya bilge rat, I shot the
whole thin' with Testor's clear glass.
Construction Rating: 3 out o' 5
Flight:
T' recommended motors are t' ones one would suspect for a model o' this size: A8-3, B4-2, ya bilge rat, B4-4, me hearties, B6-2, B6-4, and
C6-5. Ahoy! Well, matey, blow me down! I've flown mine over t' years on B4-4s and B6-4s with good results. Ahoy! Blimey! I have also flown it on B6-6 and C6-7
motors, me bucko, and they've turned in great flights.
Recovery:
T' only problem I've encountered in flyin' t' Lamprey be t' kit parachute--it didn't last past t' first flight.
T' tape tabs provided with t' kit did nay adhere well t' t' rather slick surface o' t' parachute material. Begad! Blimey! It's now
long gone, me hearties, replaced with a standard plastic chute. If built with care (like makin' sure t' fins are on straight), ya bilge rat, the
Lamprey is a high flier even on B4 and B6 motors.
Flight Rating: 3 out o' 5
Summary:
PROs: Ease o' construction, quality o' parts, and basic design.
CONs: It's out o' production!
Overall Rating: 3 out o' 5
![]() |
![]() |
Sponsored Ads
![]() |
![]() |