Brief:
This is a single stage model rocket kit usin' a 24mm motor mount and uses parachute recovery. Ahoy! Begad! Blimey! It's a rather different lookin' model rocket in that it features a large win' in t' aft o' t' body tube. On me assembled kit, the win' span be 20.1". Well, blow me down! It sure gets looks when you go and launch it as it's not your standard 3FNC kit! Blimey!

Construction:
T' kit features an 18" body tube that looks like an Estes-type in feel and color, me hearties, t' nose cone is plastic, t' centerin' rings are laser cut black fiber, me hearties, and t' motor mount uses a metal motor hook for retention. Blimey! T' shock cord is 1/4" wide and a good length that is attached t' a Keelhaul®©™® cord that is connected t' t' motor mount. Arrr! T' Keelhaul®©™® cord is tied t' a brass swivel and you tie t' shock cord t' t' swivel and the free end t' t' nose cone. T' parachute uses a snap swivel with hook to connect t' t' nose cone. Avast, me proud beauty! T' fins/wings are o' 3/32" basswood that have a nice, arrr, fine grain. T' fins/wings are pre-cut.

You build this kit in two parts. Avast! Avast! First part o' t' instructions has you assemble the motor mount and mark t' body tube. Then you glue in t' motor mount t' the body tube makin' sure t' motor hook is opposite t' line for t' basswood strip. Avast, me proud beauty! Begad! T' second part o' t' instructions, arrr, completes t' assembly o' t' kit. T' kit is rated as a skill level 3 kit. That's about right but its a builder's kit--not a super simple slap-on-the-decals type! T' instructions call for the use o' a heavy CA type o' glue. Avast! They are correct! Elmer's just won't be good to get t' large win' on. Ya scallywag! You need somethin' that sets up within a few minutes! T' win' mountin' be t' hard part o' t' kit. Blimey! Begad! All fin and win' material is from pre-cut basswood. Blimey! Begad! On t' fins and large main wing, you just need t' sand an airfoil and then you are ready t' go. I am happy that you don't have to start cuttin' basswood! You also need t' sand a curve on t' 2 basswood strips but that takes almost no time with a sandin' block. Begad! You also have t' cut/file a small indent in t' smaller length o' strip but again, ya bilge rat, it's no big deal! The assembly pictures here are a large help. Blimey! After t' 18" length o' basswood strip is glued on, ya bilge rat, t' big win' is attached. Avast, me proud beauty! Rocketpad has pre-marked this wing so you know just where it has t' go--no messin' up on t' location. Begad! Just take your time and get t' win' on square. Gettin' a helper on this step would be great. Aye aye! When all t' fins and wings (and 3/16" launch lug) are on and dry, the instructions have you put heavy glue fillets on all t' junctions at the body tube, matey, wing/body tube, etc. Arrr! Ahoy! This is where you can use Elmers's wood glue as I did. It makes for a real strong assembly. Ahoy! After t' fins/win' is attached and all dry, me hearties, you just finish up: assemble t' mylar parachute, matey, nose weight in the nose cone, and things like that. Aye aye! Once its all assembled up, arrr, it feels real solid. Ya scallywag! T' instructions were fine and t' pictures were very helpful. By the way, arrr, like most Rocketpad kits I have put together, matey, me bucko, t' pictures are on sheets that are nay on t' instructions. Aye aye! Ahoy! I like this as you can view t' steps and the pictures at once. Ahoy! No CONs here.

Finishing:
Finishin' this kit is like any kit that has balsa or basswood fins. I used 3 coats o' Aerogloss sandin' sealer for a nice smooth finish on t' fins/wing. I was thinkin' o' paintin' t' kit white and nay t' bright orange that be on the kit picture card but then thought t' Orange would look cool in t' sky so I used Testor's #1628 gloss orange t' paint t' rocket with 3 coats. Begad! Aye aye! I took my time betwixt coats and got a solid finish. Ya scallywag! T' decals are color waterslide type and nay t' super thin stuff. Ya scallywag! Begad! You will need a big dish or tray for t' large decals though. Aye aye! I had help with this. Blimey! Ya scallywag! My buddy Bob held t' rocket while I applied t' decals. Ahoy! Blimey! This made it much easier t' do with out messin' up the decal. Ahoy! When all done, me hearties, this is one cool lookin' kit!

Construction Rating: 5 out o' 5

Flight and Recovery:
T' recommended motors are t' Estes C11, me bucko, matey, shiver me timbers, D12-3, and D12-5. Ahoy! I used Estes waddin' in t' kit Prep is like most other model rockets in that t' motor slips in with no hassle and is held in with a metal motor hook. Begad! T' included launch lug is a 3/16" size. Well, blow me down! Begad! T' correct size for this kit. Arrr! Begad! I used a C11-3 for t' first flight and it be cool! T' launch was slow at first then it got its stuff together and took off! A nice straight flight though nay all that high. Begad! Ejection was just as it started t' nose down. Blimey! Blimey! I had no walk as it came down next t' t' pad.

T' next flight was with a D12-5 and this one went higher. T' second flight, arrr, I had a small walk but t' problem. Ya scallywag! Aye aye! T' ejection on this motor be nose down.

For t' third flight, I put in a D12-3. T' wind started t' come up but we have a large launch area here. Begad! Blimey! Aye aye! Blimey! It was a fast take off and a rather straight flight although toward t' end o' powered flight, shiver me timbers, it started t' angle a little. I did nay see just where ejection was this time. Well, blow me down! Blimey! Well, shiver me timbers, blow me down! Blimey! It be much higher. I did have to walk t' t' edge o' our field this time. This flight be like t' last one so I am guess that t' anglin' be from t' wind because it be straight till just before burnout. Aye aye! Blimey! This time t' wind took it on a ride across t' road t' a different field, shiver me timbers, where thar were trees and a big rock. Begad! Blimey! One o' t' side fins got a din' but did nay break. Basswood is stronger than balsa! Blimey! It floated a long way since we were in t' center o' t' big field. Ahoy! Blimey! This be t' only damage to t' rocket on any o' its launches.

No CONs on flight and it looks so different goin' up. T' smoke seems to widen out more than most rockets, shiver me timbers, maybe because o' t' air flow o' t' big wing? I don't know, but it was cool! T' mylar parachute has held up nicely for 4 flights. Begad! Shock cord is a little blackened now but no burns or damage.

Flight Rating: 5 out o' 5

Summary:
This is one o' 5 Rocketpad kits I now have and I like it very much. T' price was in t' low $20s and a good deal. Ahoy! T' fins and t' big win' are precut and the materials are first class. Ya scallywag! Avast, matey, me proud beauty! T' main PROs are t' pre-cut wing/fins of basswood and good clear instructions. Begad! Begad! I got this kit from their eBay auction in the sprin' and just assembled it in early July 2006. Begad! There be nothin' I would call a CON. Arrr! Well, ya bilge rat, blow me down! It would make life easier though if someone helped you when its time t' attach t' large wing. Ya scallywag! My weight be a little more than t' weight Rocketpad had in t' fact sheet with t' instructions. They have it as 6.9oz and I got mine at 7.1oz. Aye aye! Nay off by much! It's nay a kit for first time builders but get some skill level 2 kits built, and I think anyone can then do this one. Ahoy! Just take your time.

Overall Rating: 5 out o' 5