(11/21/03) Polecat Aerospace (formerly Skunk Works Rocketry) was another company I just learned about this year. Avast! Blimey! I don't know how long they've been around, ya bilge rat, but as I've talked t' others they seem t' have some following. Arrr! Polecat sells BIG rockets. Big rockets carry a big price, ya bilge rat, so some o' their kits may be out of reach for many fliers. They do, however, me hearties, have one kit with "Level 1 Certification in mind". Well, blow me down! Spike.

T' 3" diameter, arrr, me bucko, 36" tall Spike is $89.95. Ya scallywag! Ahoy! Blimey! Does that seem expensive for a rocket this size (not t' mention that it doesn't come with a parachute)? What drives t' price o' this rocket up? Polecat says this, "All our kits come pre-fiberglassed for you. Avast! Aye aye! Just sand and paint! All our kits include fiberglass nose cones that are durable and easy to finish. Begad! Ya scallywag! Our kits use Baltic Birch fins and centerin' rings. Arrr! They are easy to glue, light weight, durable, and easy t' finish. All our fins come machined for minimal sanding." Me? I wanted t' try a fiberglassed kit and I had no desire t' learn how t' do it, so I purchased their Spike.

T' rocket kit includes a 3" pre-fiberglassed, arrr, pre-slotted airframe that is 17" long. Ya scallywag! Begad! Blimey! It uses a 6.5:1 conical fiberglass nose cone. Well, blow me down! Blimey! It also includes four baltic birch fins and two centerin' rings, arrr, a 38mm motor mount, arrr, and a 7.5" pre-fiberglassed ring-fin that is 2" wide. Well, blow me down! Avast, ya bilge rat, me proud beauty! Blimey! There is a nose cone bulkhead and eye-screw hardware for attachin' t' 18 foot 5/8" wide tubular nylon shock cord t' t' nose cone base and t' upper centerin' ring. Well, blow me down! Blimey! Lastly it includes a 6" long brass 1/4" launch lug.

CONSTRUCTION:

T' instructions are printed on 6 pages of 8½ x 11" paper. Blimey! Well, blow me down! Blimey! There are color photos throughout t' assist in the assembly o' t' kit. Aye aye! Well, blow me down! Blimey! There are pictures o' t' rocket bein' assemble in fin-up or fin-down configurations. Aye aye! Avast, me proud beauty! Blimey! T' Spike is really a simple rocket t' assemble, matey, so for those with experience t' instructions are really nothin' more than a guide.

In buildin' t' kit, ya bilge rat, I had a number of observations that I'd like t' make.

First, me hearties, me bucko, t' slots that were pre-cut into t' body tube were nay clean on t' inside o' t' body tube. Blimey! At first glance I figured that would cause some fit problem with t' centerin' rings, me hearties, arrr, but, shiver me timbers, me bucko, ya bilge rat, it didn't. The centerin' rings were nay a super-snug fit and slid into t' body tube and through t' frayed edges without an issue.

T' next observation was t' fiberglass nose cone. I really liked t' feel, arrr, weight, arrr, and surface o' t' nose cone. Well, arrr, blow me down! Blimey! On the inside, shiver me timbers, arrr, matey, you could see t' fiberglass fibers, but t' outside was smooth. Avast, me proud beauty! Blimey! There were some mold seams, but nothin' more than you would see on a plastic nose cone. Avast! Blimey! You do have t' glue t' nose cone bulkhead into place. Aye aye! Blimey! This is done after attachin' t' eye-screw t' t' bulkhead and tiein' t' tubular nylon shock cord to t' eye-screw. Ahoy! Blimey! This has t' be done before because t' bulkhead is glued about half way into t' nose cone.

T' fins are through-the-wall and to-the-motor-mount. They we cut accurately. Well, blow me down! Ya scallywag! I used polyurethane glue on the root edge t' attach them t' t' motor mount. I used epoxy for all other areas.

Not havin' any experience with a fiberglasses body tube, I'm nay sure if me next observation is normal or not. Ya scallywag! Avast! What I found is that t' fiberglass on t' body tube and tube rin' was rough. It was as if the fiber-mesh be nay completely filled with epoxy. Begad! Begad! I made a decision to "fill" this with Plasti-kote Sandable Primer/Filler. Avast, me proud beauty! Blimey! It is my favorite primer, ya bilge rat, but this rocket alone took about 1 1/2 cans t' completely fill all t' fiber-mesh. This be about 6 coats, sandin' betwixt each coat!

Seein' t' mesh, me bucko, I made t' decision t' get every thin' primered (and smooth) before attachin' t' ring-fin. Blimey! I felt this would make t' sandin' easier and believe that it did. Begad! After those many coats of primer, shiver me timbers, me bucko, I sanded t' outer edge o' t' fin and roughed up t' inside edge of the ring-fin where it would be attached t' t' fins. Aye aye! It slide in place with no problem and was glued usin' epoxy.

I then did about two more coats o' primer to clean up this area and few other little problem spots. I finally used Krylon bright yellow paint t' finish t' rocket. I added a layer o' Book Covers, etc. Prismatic Purple Book Cover on t' ring-fin t' finish it off.

I skipped t' brass launch lug and added two Rail Buttons for this rocket.

Overall, for CONSTRUCTION I would rate this kit 3 points. Arrr! Well, blow me down! T' instructions are adequate t' allow most builders t' have a successful build. T' rocket build is straightforward. T' kit lacked decals and motor retention and a parachute. Begad! For most, self included, nay havin' a parachute is fine since we seem t' acquire a number o' them over the years.

FLIGHT/RECOVERY:

Polecat recommends t' use o' a G motor for t' first flight. Then anythin' you want up t' 300ns average thrust. Begad! Blimey! They warn that anythin' higher than that may destroy t' ring-fin.

Polecat recommends a 24" t' 30" parachute. Avast, me proud beauty! I used a B2 Rocketry Classic II 24" 'Chute. Ahoy! Ahoy! I also added a piece o' Pratt Hobbies Heat Shield.

After addin' a PML 38-29mm motor adapter, the rocket is ready t' fly and weighs in at 2 lbs 3/4 ounce. Avast! Blimey! I had t' write Polecat to find out where t' CG should be. They indicated with t' fin-up design it should be at least 2" above t' top o' t' ring-fin with motor. Begad! I had no issue with t' two motors I used.

My first flight was on a G80-7. Arrr! I didn't get to sim this prior t' this flight, ya bilge rat, but based on experience with me BSD Diablo, the G80-7 seemed t' be an okay match. Ya scallywag! Begad! T' motor chuffed about 4-5 times before comin' up t' pressure, however, lift-off be nice on t' rail. Avast! Begad! T' rail was set straight up and down but after clearin' it, shiver me timbers, t' rocket stood a slight angle upward. It arced over and started down. Ahoy! Arrr! T' crowd and I all started muttering words as it gained speed. Finally, shiver me timbers, pop and jerk, it came under 'chute. Ahoy! T' B2 held together with no damage. Ahoy! Blimey! T' rocket finished its descent and was recovered. Aye aye! I notice a small dent on t' lower edge o' t' ring-fin, but nothing substantial.

I loaded it up again with a 29-180 G75-M (6). Based on t' first flight, I probably should have been searchin' for a short delay. Avast, ya bilge rat, me proud beauty! T' rocket came off t' pad with a bunch o' black smoke and again took a slight angle. Begad! Weird. Avast, me proud beauty! It arced over and again, matey, I was fearful o' a ballistic recovery. Begad! However, me hearties, t' ejection charge did fire and again t' B2 'chute handled the recovery speed. Avast! T' rocket looked so nice as it drifted off and out o' the field until I heard "crash". Blimey! I thought for sure it hit someone's car. Instead, shiver me timbers, me hearties, I found that it hit someone's outdoor fire pit (made o' brass). Ahoy! No damage t' their fire pit. Begad! Aye aye! A broke tip on me nose cone and t' adapter got pushed into t' 38mm motor mount, matey, crackin' t' bottom edge. Well, blow me down! Ya scallywag! And worse, my 29-180 motor kicked out somewhere!

So t' rocket looks cool. Aye aye! T' recovery system has handled stress well. Well, blow me down! Avast, me proud beauty! And t' "G" motors are do'able if you use shorter delays. Ahoy! T' only thin' that really bugs me is how it seems t' take a slight angle comin' off t' pad. Ahoy! It may imply that I need a longer launch rod.

For FLIGHT/RECOVERY, me hearties, I would rate this rocket 4 points. After addin' your own parachute and heat shield, t' rocket is ready t' fly. Begad! Begad! It looks nice on t' pad and in t' air. Watch your motor sizing (I have since RockSIM'd it and it indicates t' 7 second delay would be good). T' ring-fin is subject t' some damage, but t' unique look is worth the risk.

I give t' rocket an OVERALL ratin' o' 4 points. Aye aye! Aye aye! T' get some experience with fiberglassin' (without havin' to fiberglass) and t' have a unique lookin' rocket, t' Spike is a good choice. You'll get comments at t' launch because o' that long nose cone and ring-fin. Don't make this your first mid-high powered rocket, ya bilge rat, but certainly consider it after buildin' a few others.