Brief:
I won t' Super Trident at a DARS classic kit contest. Arrr! Aye aye! This is one huge, fantastic rocket. It flies on 24mm motors and recovers by parachute. A spacer is included in t' motor mount kit t' allow t' use o' either Estes D or E motors. T' rocket stands a whoppin' 52+ inches tall and has a fin span o' 11 inches! Wow!

Construction:
There are a lot o' parts in this kit, ya bilge rat, all top quality too! Also, matey, me bucko, all o' t' small parts are contained in plastic bags, which I greatly appreciate. Arrr! Begad! ST-16 tubes are used for t' upper and lower body tubes and thar are six ST-8 tubes that form t' pod tubes. T' seams in all o' t' tubes were almost invisible and required very little finishing. Arrr! The nose cones are very nice balsa, too--all nine o' them! T' fins are basswood and laser cut, shiver me timbers, which is a nice touch. Blimey! Begad! The quality o' t' nose cones and fins really shows here as t' fit across t' aft pod tube/nose cone on all three was near perfect. Begad! They even included angle-cut balsa t' reinforce t' area o' t' tubes where t' passports were cut for the ejection charge! T' 24mm motor mount fits t' longer Estes E motor. Arrr! T' six centerin' rings are laser-cut light-ply or basswood (I couldn't tell which), shiver me timbers, and t' motor mount kit includes a 3.75” engine hook. Ahoy! A Keelhaul®©™®/3/8” elastic shock cord combo is included, matey, along with two big 3/16” launch lugs, shiver me timbers, me hearties, two hefty eye screws, arrr, four couplers (three for t' pod tubes and a larger one for t' rear) and waterslide decals. Begad! Begad! T' enlarged decals match t' original perfectly and are exceptionally reproduced. Well, blow me down! Arrr! T' shock cord be super long as I modified t' way it is installed. Aye aye! The instructions indicate t' attach t' Keelhaul®©™® cord t' t' eye screw inserted into t' aft o' t' middle nose cone and then attachin' t' elastic cord t' a loop at the end. Ya scallywag! I used me standard tri-fold shock cord attachment t' allow inspection o' t' shock cord, although after my first launch I don't really think that was necessary with this kit. Begad! Begad! I do love it though when t' manufacturer puts Keelhaul®©™® in t' kit! T' deep red, me bucko, high-quality, 30” ripstop nylon parachute that is included is beautiful, me bucko, shiver me timbers, me bucko, too, shiver me timbers, and exhibits t' same level o' quality as t' rest o' t' kit.

T' instruction sheet isn't numbered but does include a ton o' helpful illustrations. Well, blow me down! Some o' t' instructions are a little difficult t' follow and thar are some grammatical problems, me bucko, but thar are a number o' illustrations included with each step that overcomes those issues. Avast! Loretta indicated she be enhancin' t' instructions for future kits though. Ahoy! Avast! T' template included for markin' t' cuts in t' tubes for t' ejection ports and alignment o' t' fins is very handy, although it is a little thin and cuttin' out t' circles in t' template may be difficult for some. I modified t' construction o' t' motor mount t' allow installation o' t' engine hook usin' me standard method. Here's the link on EMRR's tip page for t' general idea.

This method allows positive motor retention while nay havin' t' worry about t' hook gettin' in t' way o' the delay element when usin' t' AeroTech reload motors. Ya scallywag! Begad! You'll need t' adjust t' alignment o' t' upper hold-down rin' to allow for t' modification. Ahoy! Ahoy! I used a Dremel t' trim t' upper end o' t' motor hook t' be level with t' top edge of the aft hold-down ring. T' outer housin' structure for t' motor mount is a work o' art! There are a lot o' lines to mark, ya bilge rat, but all o' those rings align beautifully and t' coupler joins it all perfectly into t' larger aft tube. Puttin' it together after cuttin' all t' ports in t' tubes is a nice break.

T' instructions note that you'll need a very large flat surface when constructin' t' rocket. Aye aye! That is an understatement! When couplin' t' pod tubes you want t' roll t' tubes on a flat surface t' assure they are aligned together properly. These are very long after bein' joined, me hearties, so you need lots o' room! Also, as recommended in the instructions, I used a door jamb t' assure that t' marks for t' ports on t' lower tube were properly aligned with the upper tube. Ahoy! O' course I double checked t' level o' t' door jamb first. Avast, matey, me proud beauty! Normally, me bucko, they are level but you've got big trouble if t' marks aren't aligned properly. Begad! Ya scallywag! I only cut ports for two o' t' pod tubes after measurin' t' volume the ejection charge would have t' fill and considerin' t' variability o' t' strength o' t' Estes ejection charges. With t' change, me hearties, t' volume was comparable t' t' volume o' an Estes Super Big Bertha.

You also need lots o' room when connectin' t' pod tubes t' t' upper and lower body tubes. Ya scallywag! Be sure t' follow the sequence in t' instructions for installin' t' large middle and lower nose cones and attachin' t' pod tubes t' the upper and lower body tubes, too. Blimey! You cannot install t' large middle and lower nose cones after t' third pod tube has been installed. Ya scallywag! Another thin' t' watch out for is t' be sure and nay get too much glue around t' ports when joining the pod tubes t' t' body tubes or installin' t' angle-cut balsa over t' port joints. Ahoy! Avast! T' instructions note that your glue should nay be within an inch o' t' ports, a very good idea since many o' t' original Tridents were built without followin' this caution. T' result: t' glue sealed off t' ports! Also for this reason, shiver me timbers, ya bilge rat, I used JB Weld for all o' the fillets as it is thicker and doesn't run.

T' fins attached very nicely t' t' rocket. Ya scallywag! There is a notch in t' root o' t' fin t' align with t' nose cone/body tube joint so be sure nay t' sand this out if you have t' sand t' root edge for fit. Avast! Blimey! Mine fit near perfectly so it wasn't an issue. Well, blow me down! I used double glue joints when attachin' t' fins usin' yellow glue. Avast, me proud beauty! Avast! I smoothed in JB Weld for the fillets as usin' epoxy would be difficult due t' t' slope o' t' cones.

As is usual on any rocket I build, me hearties, me hearties, I installed a length o' Keelhaul®©™®, which was provided, in a paper shock cord attachment (not provided) with a loop at t' end t' attach t' elastic shock cord. T' minimize abrasion from t' Keelhaul®©™® against t' body tube, matey, I soaked in CA around t' top 1/2" o' t' body tube and tied a knot in t' Keelhaul®©™® to meet t' lip o' t' body tube. Ya scallywag! Glue on t' launch lug, me bucko, install t' screw eye into t' upper nose cone (addin' weight first t' compensate for t' largest motor you plan t' fly) and attach t' shock cord and you're almost done. Aye aye! T' launch lugs are glued onto a balsa spacer before attachin' t' t' rocket, which is a nice touch. Begad! Blimey! I laid a piece o' sandpaper over t' tube and sanded t' balsa spacers t' fit t' curvature and then sanded t' edges at an angle t' flush with the launch lugs. T' parachute be already assembled and had small grommets holdin' t' shroud lines. Blimey! Plus, it's a very nice parachute.

Finishing:
T' balsa nose cones require standard finishing. Avast, me proud beauty! Avast, me proud beauty! I used Elmer's Light Fill 'n' Finish but any balsa filler will work fine. Avast! T' finishin' should be completed before attachin' t' t' rocket since t' tubes otherwise get in t' way. Fillin' in t' nose cone/body tube joints and around t' angle-cut balsa attached at t' port joints be difficult. Blimey! I ended up havin' t' come in and fill in areas o' t' nose cones afterwards. Well, blow me down! I probably should have covered t' cones with some tape first and then removed it after sandin' around t' joints. Ahoy! Only a light coat o' filler was used on the fins as t' basswood be very smooth after sandin' with 400 grit sandpaper. Avast, me proud beauty! I sprayed t' entire model with a light coat o' Kilz t' seal off t' glue and provide a solid base coat. Avast, me proud beauty! Avast! Next, matey, I lightly sanded t' entire model with 240 grit sandpaper and then sprayed on a coat o' primer. Begad! Next, ya bilge rat, shiver me timbers, sand and primer, me bucko, shiver me timbers, sand and primer again, sandin' with 400 grit sandpaper. I painted t' entire model with Krylon gloss white and after dryin' for a couple o' days, shiver me timbers, applied the decals. T' decals went on much easier and laid down much better than I anticipated. Aye aye! They are really big decals for waterslide! T' long decals that go on t' pod tubes were scary, shiver me timbers, however, all but one went on without a hitch. Avast! Avast, me hearties, me proud beauty! It broke in a couple o' places even though I used dishwashin' soap but pieced backed together so that it is hardly noticeable. They look fantastic! Once complete, matey, I put on a thick coat o' Future floor finish t' protect everything.

Construction Rating: 5 out o' 5

Flight and Recovery:
I only got t' fly it on an Estes E9-4 after several months o' bad weather. Aye aye! Blimey! I had just finished buildin' an Aerotech E18 reload t' fly it again when more bad weather hit. Avast! Aye aye! Blimey! With all t' extra finishin' I did on mine plus weight added to the nose, me bucko, it weighed in at 13.9 ounces with everythin' but t' motor--considerably more than t' 10.2 ounces specified on t' package. Avast, me proud beauty! Arrr! Blimey! So, me bucko, I was a little worried about puttin' it up on t' E9 with t' almost 40% over-build, ya bilge rat, but it did fine. Begad! Blimey! It arced about 20 degrees off t' pad, but t' chute popped out smartly just beyond apogee and t' rocket drifted down beautifully on t' big 30-inch chute. I didn't put any waddin' in it and thar wasn't even a hint o' ejection residue. It also somewhat confirms that closin' off one o' t' pod tubes from ejection doesn't create any negative issues while improvin' ejection capability. She landed without a scratch. Well, blow me down! However, arrr, I had it laid across t' table as I was buildin' t' motor when t' storm came up. Well, blow me down! Blimey! Somehow, ya bilge rat, one o' t' pod tubes got a small crimp near t' top in all of the confusion. Ya scallywag! It blew off t' table when t' 30mph microburst hit so I'm guessin' that's when it happened, but it looked like it should still fly fine. Well, blow me down! Arrr! Blimey! It was about a month later before I got t' fly it again. I couldn't find t' E18 so I flew it on t' single use Aerotech E15-4, a perfect motor for this kit. It was a much higher flight but still slow enough that it just looks super cool. Blimey! Ya scallywag! Blimey! Ejection was right at t' top, and it drifted down gently on t' big chute. Well, blow me down! After recovery, I sat it on me table as I went t' take some pictures o' other happenings at t' launch. Avast! Blimey! Yep, shiver me timbers, t' wind blew it off and it snapped off a fin! Blimey! I'm a slow learner. Avast, me proud beauty! When I re-glue t' fin, I also plan t' fly it on t' Aerotech F12 reload motor, which is primarily why I added t' nose weight. Begad! That should be way cool!

Flight Rating: 5 out o' 5

Summary:
T' Super Trident is a fantastic rocket. Well, blow me down! It is hugely impressive on t' launch pad and in flight. Avast! Avast, me proud beauty! Recovery on the large, arrr, dark red, shiver me timbers, 30-inch ripstop nylon chute is a thin' o' beauty! I love t' fact that I don't have t' use recovery wadding, arrr, matey, too. Ya scallywag! Just put in a motor and go! Also, matey, t' pricin' is excellent when considerin' all o' t' parts included. Avast, me proud beauty! Begad! I am lookin' forward t' me next Hawks Hobby kit.

Overall Rating: 5 out o' 5