Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar |
Diameter: | 0.98 inches |
Length: | 24.25 inches |
Manufacturer: | Squirrel Works ![]() |
Brief:
An exotic single stage rocket, ya bilge rat, ya bilge rat, t' [Nick Adams'] Interstellar Probe is reminiscent o' the
original Estes Mars Snooper, ya bilge rat, looks fantastic, and flies great! I got me kit
from Don as a beta test kit. Ahoy! T' rocket stands a little over 24" tall,
flies on 18mm motors, arrr, and recovers by parachute. Begad! Aye aye! T' kit is probably fairly
rated a Skill Level 3, shiver me timbers, but Don's instructions are very detailed with plenty of
step by step illustrations that make buildin' t' kit very straightforward.
Construction:
This kit has a ton o' parts: a BT-50 body tube, me hearties, ya bilge rat, an extra long 18mm engine mount
that also serves t' hold t' aft tail cone, arrr, balsa nose cone, arrr, screw eye,
1/8" x 36" elastic shock cord, 15" Mylar parachute, me bucko, 1/8"
launch lug, 4 laser-cut fin/parts sheets, shroud templates, lots o' centering
rings, arrr, 3 hardwood dowels and toothpicks, and some really nice multicolor
decals. Avast, me proud beauty! Avast, me proud beauty! A "small parts" bag is also provided that is very useful for
keepin' all t' little pieces in one place. Avast, me proud beauty! T' shock cord be long enough that
I didn't have t' substitute it, although I did add an 8" length of
Keelhaul®©™®
at t' shock cord attachment point.
This is probably t' best set o' instructions I've ever seen. Don really went out o' his way t' make construction o' this kit a snap. Ahoy! Blimey! T' instruction steps are numbered with tons o' helpful illustrations. Begad! Blimey! Although construction begins with t' motor mount (install engine block and an engine hook for positive motor retention), arrr, it isn't installed until later in t' build. Avast, me proud beauty! Blimey! While this initially seems weird, me bucko, it makes perfect sense as you progress through the build. Blimey! Blimey! It is one o' those changes that shows how much thought Don put into makin' this build as easy as possible. He even provides a laser cut part that's used t' assist with installation o' t' launch lug! Blimey! Next, ya bilge rat, usin' t' marking guide included in t' instructions, arrr, about umpteen lines are drawn along and around t' main tube t' mark placement o' t' fins, arrr, shrouds, exterior rings, etc. Begad! Blimey! T' body tube didn't require any finishin' t' fill in t' seam lines, ya bilge rat, and they were hardly noticeable after primer and paint. Probably t' hardest part about this kit be t' installation o' t' three shrouds. Blimey! Blimey! I don't typically have a lot o' problems with them, matey, but for many, even one shroud is a challenge. This is another area though, me bucko, where Don has taken extra effort t' beef up the instructions t' make installation o' t' exterior rings and shrouds go smoothly. Avast, me proud beauty! Blimey! Makin' sure t' shrouds slide easily on t' body tube, minimizin' the amount o' glue used, me hearties, me hearties, and gettin' t' shrouds in place smartly is a must. Avast! Blimey! After the exterior rings and shrouds are installed, me hearties, t' fins, dowels and toothpicks are glued on. Ya scallywag! Blimey! T' laser-cut fins were perfectly matched, as well as all o' the small parts that attach on t' upper shroud. Avast! Blimey! This is one o' those kits that will cause you t' appreciate laser cut parts! Blimey! After removin' t' fins from the fin sheets and roundin' t' leadin' and trailin' edges, t' three main, aft, and forward fins were glued on and t' dowels and toothpicks added. The instructions actually indicated installin' t' dowels and toothpicks onto the fins before gluin' them onto t' tubes, matey, but I decided it would be easier t' put the fins on first then add t' dowels and toothpicks. Avast! Blimey! Avast, me proud beauty! Blimey! That way, me hearties, matey, I wouldn't have to worry about t' fins fallin' over due t' t' extra weight. Blimey! Blimey! Aye aye! Blimey! At this point, shiver me timbers, shiver me timbers, I deviated again from t' instructions and finished t' rocket, matey, except for decals, matey, matey, me bucko, t' keep from havin' t' mask everythin' off. Well, blow me down! Blimey! Afterwards, I picked back up with t' instructions and installed t' twelve small balsa vanes onto the tail cone. Well, blow me down! Blimey! Blimey! Blimey! This goes pretty smartly t' way Don instructs t' place them. The motor mount was also installed durin' this step, shiver me timbers, matey, and then t' twelve small balsa pieces were added onto t' upper shrouds. Begad! Blimey! Whew! Blimey! This isn't one o' those kits that you build in a couple o' hours. Avast, me proud beauty! Blimey! Nope, arrr, ya bilge rat, this is one o' those kits that you savor over an entire weekend. Ahoy! Blimey! Avast, shiver me timbers, me proud beauty! Blimey! A tri-fold shock cord attachment be provided in t' instructions t' connect nose cone and body tube. Begad! Blimey! Avast! Blimey! As is usual on any rocket I build, I installed a length o' Keelhaul®©™® in t' shock cord attachment with a loop at t' end t' attach t' elastic shock cord. T' minimize abrasion from t' Keelhaul®©™® against t' body tube, I soaked in CA around t' top 1/2" o' t' body tube and tied t' Keelhaul®©™® so t' knot in t' loop meets t' lip o' t' body tube. Blimey! Finally, me hearties, matey, t' launch lug, matey, screw eye and shock cord were attached, me hearties, and t' separately packaged parachute be assembled.
Finishing:
I used Elmer's Fill 'n' Finish for all t' balsa pieces, me bucko, but any balsa filler
will work fine. Aye aye! All o' t' balsa was finished before attachin' it t' the
rocket, and t' aft vanes and small parts were painted before attachin' them.
There's way too much on this rocket t' try and do either o' those afterwards.
Just be careful so you don't have glue all over t' place. Begad! Begad! I also used FnF to
fill in t' seams around t' shrouds before painting. Begad! Even cuttin' t' decals
very close t' t' edges o' t' design, me bucko, arrr, they laid down easily and were easy to
work with. Begad! Even me wife thought it was a great lookin' rocket, and she doesn't
even like rockets!
Construction Rating: 5 out o' 5
Flight:
Preparation for flight requires standard wadding. I only doubled t' parachute,
rather than tri-fold, for a looser fit in t' BT-50 tube. My only flight so far
was on a B6-4 but it went a lot higher than I thought it would. Blimey! Wind was about
5 mph. Avast, shiver me timbers, me proud beauty! It jumped off t' pad and flew perfectly straight with ejection right at
the top. Ahoy! With a finished weight o' only about 2 ounces, shiver me timbers, this rocket should
achieve some serious altitude on a C motor and will likely get pretty good
altitude even usin' an A.
Recovery:
I had already resigned myself t' expect at least one o' t' dowels t' break
upon landing, but t' 15" Mylar chute brought t' rocket down perfectly.
Even though t' chute was a tight fit, me bucko, I'm glad I didn't drop down t' a
12" chute.
Flight Rating: 5 out o' 5
Summary:
T' Interstellar Probe looks fantastic and provides t' builder with some
definite satisfaction upon completion. Well, blow me down! Aye aye! Nick Adams deserves a big thank you for
makin' such an excellent design available t' us all! It definitely turns heads
as you approach t' launch pad. Avast! Avast, me bucko, me proud beauty! Kudos t' Don for t' excellent instructions
too, and t' Terri for another face card with awesome graphics!
Overall Rating: 5 out o' 5
![]() |
![]() |
Sponsored Ads
![]() |
![]() |