Brief:

T' Semroc Space Shuttle is a faithful reproduction o' an old (OOP) Centuri kit that was introduced in 1971. Aye aye! It is a close approximation t' t' original full-scale model. Arrr! Avast, me proud beauty! All fins and rings are precision laser-cut balsa and sturdy fiber. Well, blow me down! Begad! T' plastic nose cones are replaced with much lighter balsa reproductions.

Construction:

T' instructions are well written and easy t' follow with clear drawings for t' most o' t' 53 steps. Ahoy! For a small model this kit can take a lot o' time dependin' on what you want t' do.

All o' t' parts are good quality includin' t' balsa wood. Avast! I decided t' coat all t' balsa fins with CA, me hearties, me bucko, which took time.

A friend had told me that Golden Mediums GAC 100 Multi-Purpose Acrylic Polymer be good for fillin' balsa by spreadin' it on with a stiff piece o' plastic like and old credit card. I tried this material, but I’m nay sure that it helped that much. Aye aye! After paintin' most o' t' balsa grain has disappeared on t' both nose cones and t' orbiter fins, me bucko, me bucko, but some grain can be seen on t' booster wings.

I decided t' hollow out t' nose cones, ya bilge rat, but t' instructions do nay call for this procedure. Aye aye! Begad! I later found t' model t' be unstable in flight, but it is hard t' believe that this amount o' balsa could equal all t' lead weight that I later added. In order for t' pop-pod t' work correctly t' glider nose cone must be glued in.

Conceivably, ya bilge rat, t' nose cone on t' booster could be left unglued for booster flight trimming. I did nay want t' gap t' show, shiver me timbers, so I glued both nose cones t' their body tubes. Avast, me proud beauty! Steps 7 through 10 establish t' location o' t' wood dowels on t' booster for attachin' t' orbiter. Well, blow me down! Follow these steps closely. Avast!

Especially, follow Step 10, me hearties, shiver me timbers, me hearties, which states that t' pieces must be within 1/16” o' t' specified locations. Ahoy! Later, after paintin' I found that I had t' sand and trim some o' theses parts with an X-acto knife t' make them fit properly. Avast, me proud beauty! Avast! I put a small silver mylar adhesive strip on t' aft motor mount tube under t' engine hook. Aye aye! Blimey! This should be done just before Step 18.

Step 19 turned out t' be t' most difficult for me. Arrr! I followed t' directions in Step 19 and put a small amount o' wood glue in t' top end o' t' engine tube and proceeded t' slide t' thrust rin' (motor block) down t' t' engine hook. However, shiver me timbers, t' glue had soaked into t' body tube and t' thrust rin' actually tipped over in t' process and hung up. Ahoy! Avast, me proud beauty! Luckily, I had a long stick available in t' workshop. Blimey! Begad! I put t' stick through t' opposite end o' t' body tube and pushed t' thrust rin' out. Blimey! Needless t' say, me bucko, t' next time I repeated this step, I used a wood dowel and placed t' glue down by t' engine hook before I slid t' thrust rin' into place.

Finishing:

This shuttle concept reminds me o' t' Monogram plastic models that Willy Ley, a German rocket scientist, help advertised back in 1958. Ya scallywag! T' model consisted o' a large winged booster on t' bottom and a winged orbiter vehicle on top.

T' booster had a bright red color. T' Semroc directions show a yellow orbiter on top o' a white booster, which is probably consistent with t' original Centuri configuration. Ahoy! I be taken t' makin' an orange orbiter, probably from me recollection o' seein' some Bell X-1 models painted orange. Blimey! Begad! I used t' old Rustoleum rust colored primer, which was very difficult t' cover with t' new Krylon gloss pumpkin orange that came out about a year ago.

After 5 coats or more I succeeded in coverin' t' primer with t' Krylon orange. T' coverin' power o' t' Krylon be nay good and it had a tendency t' be transparent. T' booster and orbiter weights from t' instructions are listed t' be 1.5 oz. Aye aye! and 0.5 oz., respectively. Avast! My painted and finished booster and glider weights turned out t' be 2.5 oz. Avast! and 0.5 oz., respectively. I did nay use all t' Semroc decals and preferred t' use some different decals that I had in me inventory. Begad!

Flight:

T' first flight with an Estes C6-3 proved t' be unstable and t' Shuttle fishtailed badly without gainin' much altitude. Arrr! Avast! T' altitude be only about 50 feet and t' motor pod ejected on t' ground. Only one fin was broken and it was easily reattached with super glue gel.

T' second flight was again with a C6-3, but this time I epoxied about 0.5 oz o' lead weight behind t' forward bulkhead on t' motor pod. Blimey! Blimey! I bought t' lead weight at a fishin' tackle store. Avast! Arrr! It comes in a coil and is referred t' as No. Avast, me proud beauty! 1 3/16” hollow. Blimey! This time t' shuttle took off t' about at an altitude o' 20 feet and flew vertical t' t' ground. Avast! Arrr! Again, t' motor pod ejected on t' ground and one fin broke off and was easily reattached.

For t' third flight with a C6-3 I added about another 1 oz. Avast, me proud beauty! o' weight. Ya scallywag! Well, blow me down! This time I epoxied a wooden dowel as a boom t' inside o' t' motor pod. Avast! Since I had hollowed out t' nose cone o' t' orbiter, me bucko, I had room t' move t' lead weight forward. Avast, me proud beauty! I also noticed that t' orbiter was a little bit loose on top o' t' booster, matey, so I added some balsa shims that removed t' wobble. Begad! Begad! On this flight t' Shuttle flew straight and had enough altitude about 120 feet t' eject t' motor pod. Avast, me proud beauty! T' booster did glide for a very short distance before landing, but t' orbiter did nay glide very well. Begad!
Care needs t' be taken in flyin' away from spectators, arrr, because t' pod does fall fast. Well, matey, blow me down! I am now plannin' t' attach a small 8” square parachute t' t' pod. Arrr! Begad! Also, matey, I am plannin' t' next launch with an Apogee D10-3, me bucko, which be t' same size as t' Estes C6-3. Well, blow me down! Well, blow me down!