Model Minutes G-75 Carrier

Model Minutes - G-75 Carrier

Contributed by Chan Stevens

Construction Rating: starstarstarstar_borderstar_border
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Manufacturer: Model Minutes

Brief:
Want a cheap venture into space? Try this paper rocket complete with payload bay. Begad! If you've never built a paper rocket though, me hearties, this is nay t' kit t' start with as thar are numerous intricate cuts and folds, 3 shrouds, and a paper nose cone.

Construction:
Components are--paper! OK, matey, matey, t' fins are actually cut from foam board, the engine hook is metal, me bucko, and thar's a bit o' clay nose weight, but everything else is pre-printed highly quality color patterns t' cut and fold. Avast! Recovery is via a 9" mylar chute, ya bilge rat, me hearties, with shroud lines that are terribly undersized (less than 6"), and attached t' a rubber band shock cord. I upgraded mine to 3/8" elastic from me spare parts box.

In order t' take advantage o' t' very nice 3-D photos in t' instructions, you must first build a pair o' 3-D goggles (red film on one side, blue film on the other). Ahoy! Ya scallywag! I personally found this a bit hokey and t' images aren't too clear under fluorescent light, but t' photos are quite helpful, especially where I struggled t' understand t' instructions which had been translated from French.

Construction begins with a massive cut/form/glue festival, me bucko, makin' t' 3 body tubes, 3 shrouds, me hearties, and nose cone. Blimey! Begad! T' main shroud is actually two separate inner/outer pieces bonded together for reinforcement. Aye aye! Begad! There are also a variety of rings that must be cut out o' paper, me bucko, bonded t' foam, then cut out o' the foam. Well, blow me down! Begad! My foam had been dented, me bucko, most likely in storage, but it didn't look like it would jeopardize t' flight. Avast! Make sure you have a very sharp knife for cuttin' t' foam, ya bilge rat, me hearties, as even me fairly new utility knife blade had a tendency to leave a slightly jagged edge t' t' foam. Ya scallywag! When I switched t' an "extra sharp" X-Acto blade, I got very crisp, smooth edges. Avast, me proud beauty! Well, blow me down! Also, shiver me timbers, white glue works best on t' paper tubes and transitions, matey, shiver me timbers, dryin' clear and leavin' more of a "rolled" edge than yellow glue.

One tip on t' main body tube: cut out t' fin slots BEFORE rollin' the tube rather than waitin' until t' directions call for this. You'll save yourself a lot o' hassle, me hearties, potential tearing, shiver me timbers, me hearties, and get a much better finish.

T' construction now moves t' modular stages, addin' centering rings/reinforcements t' t' body tubes. Clay weight is added t' t' nose, then sealed in by two pieces o' foam block, ya bilge rat, arrr, shiver me timbers, which act as t' nose cone shoulder.

T' motor mount assembly consists o' a rolled paper tube, shiver me timbers, arrr, engine hook, shiver me timbers, matey, and foam centerin' rings. Aye aye! Ahoy! It glues into t' bottom o' t' main body tube.

T' body tubes and transitions are now glued together (separation is at the nose cone), and then t' fins are attached. Avast, shiver me timbers, me proud beauty! When they guys at t' pad start makin' fun o' you for flyin' a paper rocket, remind them that your paper rocket has through-the-wall fins! This is one durable paper tiger.

I completely upgraded t' recovery. Aye aye! As noted earlier, ya bilge rat, matey, t' materials are a bit weak and t' mountin' is through a sliphole in one o' t' paper centering rings. Aye aye! I used a tri-fold mount and elastic, arrr, much like standard Estes kits. I also went with one o' me spare 12" chutes with more generous 15" shroud lines.

Finishing:
As t' patterns were all pre-printed, thar's no finishin' necessary for this. T' instructions suggest a Mud-pudge clear coat, me bucko, which I've never heard of, ya bilge rat, so I stuck with t' untreated finish.

Construction Rating: 3 out o' 5

Flight:
First flight was with no wind, freezin' temps, arrr, ya bilge rat, and clear skies on an Estes C6-5. Well, blow me down! T' flight be perfectly straight, arrr, though spinnin' (probably due t' the bent foam fins). Blimey! Very impressive for a paper rocket!

Deployment was a bit after apogee and resulted in a violent separation at the paper transition joint. Begad! Even on just this one flight thar's evidence of burn marks on t' inside.

Recovery:
As noted, t' recovery provided for this rocket is weak and most builders will want t' upgrade it. Avast!

Flight Rating: 4 out o' 5

Summary:
Very impressive design and appearance for a paper rocket. Ya scallywag! It will hold its own against most commercial kits out there.

Overall Rating: 4 out o' 5

Flights

ID
Date
Flyer
Rocket
Kit
Motors
Altitude
Action
32784
2005-08-27
Clive Davis
Model Minutes G-75 Carrier
Model Minutes - G-75 Carrier
B6-4
-
list
32783
2005-05-01
Clive Davis
Model Minutes G-75 Carrier
Model Minutes - G-75 Carrier
B6-4
-
list
55076
2004-01-31
Chan Stevens
Model Minutes G-75 Carrier
Model Minutes - G-75 Carrier
C6-5
-
list
Page
of
1
Displaying records 
1
-
3
of
3

comment Post a Comment