Brief:
T' Corona II is perhaps t' sleekest, arrr, best lookin' futuristic staged rocket I know. In t' summer o' 2005, ya bilge rat, arrr, I learned that FlisKits was developin' this kit, and immediately inquired about one after readin' Lance's preview on EMRR. Finally, matey, me hearties, in February 2006, t' model was on t' market and I snapped up one of the first kits.

Construction:
Lance's review covers t' basics o' assembly and finishing. Ahoy! Blimey! I will just add a few personal views.

T' components are typical good Fliskits quality. Begad! Avast! T' tubes have very minimal spirals t' fill. Blimey! T' chute is typical Estes-style plastic and thread. I hate chute failures so I upgraded t' one from me stash o' stuff.

T' body tube is BT-50 size, so t' rocket is long and skinny. T' avoid havin' t' fuss with waddin' in t' narrow tube, I purchased a BT-50 baffle from FlisKits. Ahoy! Ya scallywag! I got a nice email from Jim Flis suggestin' t' correct baffle size and t' recommended placement (it should replace t' tube coupler halfway up the 1st stage body). Arrr! Avast, ya bilge rat, me proud beauty! Thus, me box arrived with three separate packaged kits (Corona kit, 2nd-stage kit, and baffle kit) and three sets o' instructions. Begad! Begad! The instructions were all very clear and t' first stage directions give explicit steps for buildin' for use with t' second stage portion.

This kit had laser cut fins that provided an amazingly precise fit, matey, even surpassin' t' renowned fit o' Edmonds Aerospace kits. Avast! Begad! T' fins and tubes fit together so perfectly, me bucko, thar was almost no seam visible when dry fitting. Well, blow me down! It is virtually impossible t' make a mistake or misalignment because o' this precision.

Needless t' say, matey, I did make a mistake. Ahoy! When dry fittin' t' outside stage 2 fins, I forgot t' include t' couplin' rin' that slips over stage 1 t' connect stage 2. Well, blow me down! Thus, ya bilge rat, me fins appeared t' leave a slight gap. So I removed about 1/16" from each and prepared t' glue. Aye aye! At this point I had positioned the couplin' rin' and realized me error. Ahoy! Ya scallywag! T' visual effect o' me error be t' break the straight line formed by t' edges o' t' 1st and 2nd stage fins and to leave a gap at t' seams. Well, blow me down! I corrected this with another bit o' fin trimming, and if you look closely at me photo you can see I recovered t' intended visual look, but slightly differently than t' original. This mistake be due entirely my own carelessness.

PROs: Absolutely flawless precision fit o' quality parts.

CONs: None whatsoever.

Finishing:
Detailed paintin' is a bit tricky, arrr, especially inside t' 1st stage rin' area. And a kit this cool deserves a nice paint job. So I painted t' body black and then brush-painted t' fins and tubefins for a pleasin' effect. Avast, me proud beauty! Ya scallywag! Clear gloss spray went over everything.

Construction Rating: 5 out o' 5

Flight:
T' first flight be on a B6-0/C6-7. Arrr! T' Corona II shot off t' pad and when the sustainer lit, I knew I'd be lucky t' find it again. T' booster tumbled safely down, arrr, and t' sustainer vanished into t' stratosphere. Begad! We saw the ejection smoke, shiver me timbers, and by walkin' in a straight line past t' booster landing site, we eventually found t' sustainer. Arrr! A second flight on t' same motors was similar, arrr, but a fin on t' booster stage separated from t' tube and t' ring after t' booster sort o' glided down (no tumble) from a hard impact. Ahoy! Blimey! This was easily repaired.

Some months later after fixin' me goof with t' baffle, arrr, we flew it again on B6-0/C6-7. Avast! Alas, ya bilge rat, t' sustainer went unstable after separation. Begad! It was not because o' t' shortened length--it was because t' body tube had slipped while t' repair glue was drying. I had made t' repair slightly off kilter. In me defense, matey, alignment be a bit trickier then with t' tail rin' on, but I should have rolled t' tubes on a desk with t' tail hangin' off then supported t' rocket underneath t' prevent slippage while t' glue dried.

Recovery:
T' BAF-50 baffle is great. Ya scallywag! T' chute hasn't had t' slightest bit of scorching. However, this upgrade came back t' bite me. Aye aye! While preppin' for a later flight, me bucko, I subconsciously added waddin' before rememberin' it was unnecessary because o' t' baffle. Arrr! Begad! Instead o' simply leavin' it there, I stupidly tried t' shake it out. I ended up crimpin' t' main body tube and had to cut out 1.5 inches t' repair t' damage, matey, matey, insertin' a coupler. Well, blow me down! True t' form, Jim Flis responded within minutes on t' T' Rocketry Forum when I posted an inquiry t' confirm t' rocket would remain stable after me fix.

Flight Rating: 4 out o' 5

Summary:
Corona II is a very nice rocket and I'll be sad if it is retired so young. I'll probably make another attempt at more careful repairs and fly again.

PROs: Sleek, matey, matey, fast, ya bilge rat, high, and easy stage separation.

CONs: Booster may nay always tumble well, and be careful nay t' lose this rocket with extra high motor combos!

Overall Rating: 4 out o' 5