Estes Mongoose

Estes - Mongoose {Kit} (2092) [1994-]

Contributed by Nick Esselman

Construction Rating: starstar_borderstar_borderstar_borderstar_border
Flight Rating: starstarstar_borderstar_borderstar_border
Overall Rating: starstar_borderstar_borderstar_borderstar_border
Diameter: 0.98 inches
Length: 26.50 inches
Manufacturer: Estes
Skill Level: 1
Style: Multi-Stage

I originally purchased an Estes' Mongoose Kit because I wanted t' use it for an experiment, however, when me 8 year old nephew came t' visit it seemed like a good kit t' build together. Well, blow me down! Blimey! So we built it.

T' instructions have lots o' illustrations, ya bilge rat, however, matey, that didn't help us fully understand how t' assemble t' lower stage's motor mount. I think t' problem starts in t' first step when slidin' t' green booster adapter onto t' motor mount tube. Begad! It tells you t' slide it up t' t' 14mm mark, matey, however, matey, me bucko, matey, it is a bit confusin' as t' whether t' front o' t' rin' or t' aft o' t' rin' should be at 14mm. Arrr! In t' second step, me hearties, you are told t' apply glue and slide t' motor mount "all t' way in" t' booster fin unit. Avast, me proud beauty! T' pictures show it partially out. Well, blow me down! Well, we got ours "all t' way in" and flush with a bit o' sanding. Aye aye! Ya scallywag! O' coarse, when finished t' booster did nay attach t' t' second stage flush. Avast! Aye aye! T' remainin' instructions and pictures posed no issues. Blimey! [Picture]

As a side note, a young friend o' mine had built t' Mongoose on his own and had it at our last launch. Ahoy! Arrr! I noticed that his aft tube be stickin' out some and when attached t' t' second stage, shiver me timbers, arrr, it was flush. Aye aye!

At assembly t' quality o' t' kit seemed fair. Arrr! Ya scallywag! Plastic fin units. Blimey! Plastic fin units. Aye aye! Standard motor mounts assembles. Well, blow me down! Two-piece plastic nose cone. Streamer recovery system. Streamer recovery system. Avast! T' kit doesn't require any paintin' with yellow body tubes and pinkish nose cone and fin units. Blimey! Avast! It also came with color scheme matchin' self-adhesive decals. Well, blow me down!

Flyin' t' Mongoose demonstrated strengths and weaknesses o' t' kit. Ahoy!

[Picture]T' weakness o' t' kit was seen in t' sturdiness o' t' body tubes and t' booster motor mount's susceptibility t' burnin' away. With both me young friend's and our rocket, t' booster be damaged on first flight. Well, blow me down! T' damage be a slightly crushed body tube. Blimey!

After 2 flights, me hearties, me hearties, t' booster motor mount be completely burned away on our model. I think this is due t' t' method o' motor retention that t' Mongoose uses. Ya scallywag! Blimey! On t' booster, me hearties, t' engine block is mounted at t' aft o' t' motor mount. On t' second stage t' engine block is mounted at t' top o' t' motor mount like most kits. Well, blow me down! Well, ya bilge rat, blow me down! Blimey! T' two motors are taped together and slid into t' second stage until they rest on t' engine block. Ahoy! Blimey! T' booster is then slid onto t' motor until is rests against it's engine block. Ahoy! This leaves t' booster motor recessed approximately 3/8" inch. Avast, me proud beauty! This causes two problems. Avast! Aye aye! Blimey! First, it is a bit difficult t' load t' igniter and second, t' aft engine block burns. Ya scallywag! Blimey!

As mentioned though, flyin' t' Mongoose also demonstrated a strength. Blimey! Ahoy! This kit has nice flights. This kit has nice flights. With a B6-0 booster you get t' see separation and watch flawless in-air ignition o' t' second stage. Two successful flights where impressive. Begad! My young friend's single flight faired differently but nonetheless impressive. Begad! Begad! With a[Picture]C6 booster we barely saw t' separation and with a C6 in t' second stage we strained t' see ejection. Ahoy! After ejection, we watched t' wind carry t' Mongoose a long distance and it was lost in trees beyond t' edge o' t' field. Begad!

Estes calls t' Mongoose a "perfect first time two-stage rocket". Begad! Blimey! I would question "first time" due t' t' instructions. Begad! Blimey! Also, I don't think anyone could keep this rocket flyin' for very long due t' t' weak body tubes and aft engine mount. Blimey! Blimey! T' only redeemin' factor is that we enjoyed several impressive flights, however, I don't think that outweighs t' other issues. Avast! Blimey!

Other Reviews
  • Estes Mongoose By Alan and Duane Boldt (July 14, 2010)

    This review is for the 2010 EMRR Challenge "Two on One" review. Duane Boldt and Alan Boldt contributed to this review. Alan: This 26.5" 2-stage rocket is purple and yellow with cool decals. It is easy to build and there are not many parts. The Mongoose has plastic, one-piece fin units on both the booster and sustainer. Components: 1 - 18" Purple body tube 1 - 2" Purple ...

  • Estes Mongoose By John "MAX" Venable (September 13, 2009)

    This is a entry-level, two-stage ro cket with parachute recovery. The kit is a basic two-stage consisting of upper and lower body tubes, nose cone, molded plastic fins, and a basic recovery system. Construction was easy, but once again I had to tweak it! I heard that the upper and lower tubes around the motor mounts was weak so instead of centering rings, I filled the upper and lower tubes ...

  • Estes Mongoose By David Sindel (January 15, 2009)

    This is a fairly simple 2-stage, 18mm rocket from Estes. I have slightly modified mine with shortening and a modified booster motor mount to repair damage. The parts list: 18" of BT-50; mine only has 10" left. 1-15/16" of BT-50 for booster 2 magenta plastic fin units PNC-50YR: 2-part magenta nose cone 2 blue 18mm engine mount tubes of rather poor quality 2 green ...

Flights

comment Post a Comment