Brief:
This rocket is based on plans from http://www.lansbergen.net. Aye aye! Well, blow me down! Blimey! Philippus Lansbergen has some really cool paper model plans o' scale model rockets, fantasy rockets, gliders, and UFOs. They are nay flight-worthy rockets, shiver me timbers, me bucko, but with a little modification they can be made t' fly off a launch rod. Avast! Blimey! I be attracted t' t' Ranger Ray's rocket because it be so clumsy and campy. Avast, me proud beauty! Ahoy! Blimey! I thought it would be a fun conversion. Begad! In order t' find t' plans, ya bilge rat, ya bilge rat, you have t' click on t' "Modelbouw" link on his site.

Construction:
Here is what you need t' make your own Ranger Ray Rocket:

• Cardstock
• Keelhaul®©™ shock cord material
• Shock cord and streamer
• Screw eye for nose cone
• Clay or BBs for nose weight
• 13mm body tube (BT-5)
• Engine block

T' instructions are pretty minimal (mostly illustrations with some Dutch and some English), but t' rocket goes together pretty quickly. Ya scallywag! T' rocket consists o' three different body tube shrouds because o' t' different diameters. Ya scallywag! Each connectin' section o' t' shroud has an additional transition part that sits inside t' main body shroud. Begad! Begad! I designed me version t' have t' upper most shroud be t' nose cone. T' fins fold together easily and are quick t' attach t' t' side o' t' rocket. Ya scallywag! Creatin' nose cones out o' paper can be difficult, matey, but with practice, it becomes easier and easier.

Next, arrr, I cut some space in t' bottom nozzle/bulkhead o' t' plans t' make room for t' 13mm motor mount. Arrr! After makin' a few test fittings, matey, I glued t' nozzle together and let it dry. Begad! After t' nozzle unit be dry, shiver me timbers, arrr, I glued t' 13mm motor mount t' t' nozzle, along with a small centerin' ring, arrr, and fit t' motor mount into t' rocket from t' bottom. I made sure t' motor mount was long enough t' make it t' t' top o' t' second shroud. Arrr! Avast! Once dry, shiver me timbers, I could glue t' engine block with Keelhaul®©™ into t' motor mount.

Lastly, I added weight t' t' nose cone (nose cone weighs about 5 grams) and used some extra card stock t' roll a plug that would sit within t' motor mount tube. Blimey! T' plug would act as t' shoulder o' t' nose cone, arrr, ya bilge rat, keepin' both parts o' t' rocket together for t' flight. I plugged t' shoulder with some glue and tissue paper, arrr, let it dry, shiver me timbers, ya bilge rat, shiver me timbers, and then put in t' screw eye with CA for t' shock cord. Avast! All I had t' do was tie t' shock cord t' t' screw eye and attach t' streamer.

PROs: Cheap rocket, cool design, matey, quick t' build, matey, and parts easily replaced.

CONs: Paper construction can be fragile. Arrr! T' cardstock I used be very wimpy and me fins turned out a little leathery at t' end. They have a tendency t' curl when I place t' rocket upright.

Finishing:
Since all t' detail is printed on t' paper, me bucko, thar be really no paintin' required.

I have built numerous paper rockets, and am always thinkin' about how t' strengthen t' paper for launching. Avast! Well, blow me down! I used ModPodge (MP) on Ranger Ray's Rocket, shiver me timbers, shiver me timbers, and if you look closely at t' photos, me bucko, you can see t' built-up gloss that MP leaves. Aye aye! Avast! I am nay entirely convinced that MP be t' way t' go since it does have t' tendency t' cause t' ink t' run a bit. Aye aye! Next time I will try an acrylic spray coat first and then add t' MP. Avast! Also, ya bilge rat, I added about 3 or 4 layers o' t' MP t' get a nice build-up/coatin' on t' rocket.

PROs: No paintin' required and no decals need t' be applied.

CONs: You need a color printer for best results.

Construction Rating: 4 out o' 5

Flight:
I flew t' rocket twice, once usin' an A3-4T, and a 1/2A3-4T. Blimey! Interestingly, matey, t' 1/2A3-4T had just t' perfect delay. Well, blow me down! T' rocket really reached a nice high altitude on t' A3-4T. Begad! T' 1/2A3 flight be nice t' watch but nowhere near as exciting. Aye aye! T' model is easy t' prep. Ahoy! I used waddin' and tape t' friction fit t' motor since thar be no engine hook.

Since t' nose cone weighs more than t' rest o' t' rocket, me bucko, matey, shiver me timbers, it came down pointy end first both times. Aye aye! T' nose cone is slightly damaged (a little rip), shiver me timbers, me hearties, ya bilge rat, but I think that it can easily be repaired. Ya scallywag! I now have a better sense o' how t' build stronger paper nose cones, shiver me timbers, me bucko, which is by buildin' up t' insides with additional card stock and wood glue.

Recovery:
Pros: It only costs a few cents t' build another rocket if anythin' gets slightly damaged on recovery!

Cons: T' 13mm motor mount is very small, so t' streamer that fits inside cannot be very large. T' rocket flies surprisingly straight and is fun t' build and fly. Ya scallywag! Well, ya bilge rat, blow me down! If a larger streamer could be put inside t' rocket, perhaps t' nose cone wouldn't suffer dings t' readily.

Flight Rating: 4 out o' 5

Summary:
PROs: Cheap, fun, matey, goofy rocket. Considerin' t' plans are free, me hearties, ya bilge rat, it's a great build. Blimey! T' rocket is very stable (make sure you don't forget nose weight!) and flies well.

CONs: Dealin' with paper is always a problem. Well, blow me down! First, with creatin' paper shrouds thar are always goin' t' be seams. Avast, me proud beauty! If you don't like t' deal with visible seams, ya bilge rat, then don't get involved with paper rocketry. Well, blow me down! Also, arrr, ya bilge rat, arrr, If you want t' build a solid rocket, shiver me timbers, then you will have t' find a way o' beefin' up t' strength o' t' paper.

Overall Rating: 4 out o' 5