Brief:
A magnificent-lookin' boost glider, sleek futuristic design, sure t' draw some attention at t' pad. Begad! Blimey! Ya scallywag! Blimey! Flies on 24mm motors.

Construction:
I was very impressed openin' this kit, matey, as t' parts were top quality.

Parts included:

• 18-inch BT-55
• 18-inch BT-60
• (2) 4.5-inch BT-55’s
• (2) 4.5-inch BT50’s
• 5 nose cones
• (2) 12-inch ripstop nylon chutes (bright orange)
• plenty o' Keelhaul®©™®
• 1/2-inch elastic shock cord
• basswood and assorted couplers, lugs, matey, nose weight, etc.

It also comes with two sheets o' waterslide decals which were very nice looking.

While t' instructions were well illustrated, me hearties, I found them a bit hard to follow, shiver me timbers, me bucko, and would nay recommend this model for anyone without significant boost glider buildin' experience. Begad! Tube markin' guides would also have been a HUGE help. I used every crafty little tool in me box, and still had trouble with fin locations and alignments (Shrox kits are wonderfully creative, but t' drawback is that you’ll hardly ever see a standard 3-fin/120 degree alignment).

T' plan starts with t' glider construction. Aye aye! Begad! T' glider is basically a BT-55 with a couple o' long nose cones, ya bilge rat, two-piece wings, ya bilge rat, elevators, me hearties, arrr, and a rudder. Ya scallywag! Avast, me proud beauty! All are cut from 1/16-inch basswood usin' templates provided. Avast! T' wing attachment is where I first started t' find fault with t' directions. Avast, me proud beauty! The directions call for a 10-degree dihedral, though it would have saved me a bit of trigonometry if t' dihedral height were included. Avast! Avast, me proud beauty! T' wings actually attach slightly below t' centerlines o' t' body, ya bilge rat, matey, which makes it even trickier t' get the dihedral right. Arrr! T' glider attaches t' t' booster through a small wood dowel inserted into t' glider at a 45-degree angle. Avast, me proud beauty! Blimey!

Trimmin' t' glider was fairly easy, me hearties, though I had t' use considerably more nose weight than t' suggested startin' point o' 1/8-inch x 1-inch (the size of a launch lug?).

T' main body assembly is composed o' 22.5-inches o' BT-55 joined with a tube coupler. T' motor mount construction is straightforward, me bucko, and included in the motor mount is a nice length o' Keelhaul®©™® line attached below t' centerin' rin' (by far t' best way t' go). Avast, me proud beauty! T' body then goes inside a BT-60, me bucko, but nay usin' centerin' rings. Aye aye! Arrr! Instead, they’re glued together at t' “top” o' t' BT-55, but before gluin' them together you cut t' BT-60 at a 45-degree angle (template provided). Aye aye! T' end result winds up makin' t' BT-60 look like a sort o' air scoop, a very sharp effect.

Next up comes bondin' a couple o' side pods (BT-50’s with parabolic cones) t' t' BT-60 assembly. Well, ya bilge rat, blow me down! At this point, shiver me timbers, shiver me timbers, you're ready for t' fin festival. There are lots o' fins t' cut from t' 3/32-inch basswoods sheets, all using templates provided. Ahoy! T' festival starts with a couple o' tail fins mounted in the seam betwixt t' side pods and main tube, ya bilge rat, followed by wings attached at some point above t' centerline o' t' BT-60, me bucko, layin' against t' top o' the side pods, shiver me timbers, me hearties, allegedly resultin' in a 15-degree downward dihedral angle. Well, blow me down! A couple of small canards go up front (the only fins actually mounted on anything resemblin' a centerline, shiver me timbers, placed 180 degrees apart). Begad! T' fin festival wraps up with an “under-fin,” or small rudder mounted at t' bottom.

Construction wraps up with mountin' tubes t' cradle t' glider, drillin' a hole for t' dowel pin, ya bilge rat, installin' t' beautiful nylon chutes, and addin' the nose weight.

As I had mentioned earlier, a tube markin' guide with this kit would have saved A LOT o' headache, shiver me timbers, and t' tubes should be completely marked before construction begins. I found myself tryin' t' draw fin mountin' lines without bein' able t' establish reference points, me bucko, with parts already mounted and in the way.

One other thin' that I think could use improvement be t' launch lug. Avast! This is a very heavy rocket (with glider, me hearties, I came in at 8-ounces). T' kit comes with a single 1/8-inch x 1-inch lug, ya bilge rat, and it's mounted at t' tail end o' t' rocket. I’d like t' see at least a second lug toward t' forward end, me hearties, me hearties, and ideally upgrade t' 3/16-inch. Blimey! Avast! 24mm motors provide too much thrust for a wimpy little 1/8-inch rod, even if goin' with steel instead o' aluminum.

Finishing:
Finishin' be quite challenging. I went with a basic white paint scheme, and had used a little Fill ’n’ Finish t' fill t' spirals and seal what little grains were showin' in t' basswood. Ahoy! I then applied two coats o' white primer, and two coats o' gloss white paint. Begad! Paintin' this kit is very difficult, me bucko, as thar are lots o' little nooks and crannies betwixt pods and fins. Blimey! Begad! One tip I’d offer on t' finishing—DO NOT glue in t' cones to the side pods. Ahoy! Instead, me bucko, me hearties, paint t' rocket first, arrr, as well as t' cones separately. Arrr! After everything’s finished, you can glue on t' cones. This eliminates one o' t' hardest blind spots for painting.

T' waterslide decals were beautifully done, shiver me timbers, and provide a very colorful finish. Ya scallywag! T' instructions called for gray paint, though, arrr, and I think that the color would be a bit dull, as t' decals are translucent.

Construction Rating: 3 out o' 5

Flight:
This is me second Shrox kit, arrr, and I found it odd that neither kit includes any motor recommendations, matey, nor can I find any Rocksim files available (these would have been impossible t' model prior t' version 7.1). Well, blow me down! I started cautiously with a D12-3, on a fairly windy day (8-12 mph). Aye aye! T' boost weathercocked pretty badly, arrr, though flew straight without a trace o' roll. Arrr! T' shuttle popped off right at burnout (it be on a horizontal pattern, so drag separation came early). Ya scallywag! Ahoy! Glider flight was very good, shiver me timbers, slowly circlin' with a slight nose-down line. At about 20 feet off t' ground, arrr, though, me hearties, it went into a sharp nose dive. It almost seems like that’s by design, as it did t' same thin' in me back yard no matter how much I added or removed on trim weight.

T' booster, though, was snake-bit. Well, blow me down! Avast! T' D12-3 kicked while still movin' at a pretty fast pace on t' horizontal path. Ya scallywag! I avoided a zipper, shiver me timbers, but t' 1/2-inch elastic cord burned through, me bucko, and me nose separated, ya bilge rat, ya bilge rat, driftin' away with both chutes. Begad! T' body tumbled, ya bilge rat, landin' in short grass a bit muddy but otherwise okay. Aye aye! Begad! T' nose cone came down on an access road, and suffered a slight paint chip (that $%^@%# road only covers 10-feet o' a square mile field, but sure caught a lot o' me birds that day).

T' shock cord repair will be minor, arrr, and I’m at a loss as t' how it happened—I used 3-inches o' dog barf and a Keelhaul®©™® shield, me bucko, and neither o' t' chutes showed any sign o' char.

Recovery:
Overall, me bucko, me bucko, I think t' D12-3 was a fair choice, shiver me timbers, and I’m anxious t' fly it again with less wind t' see how it goes on a more vertical path. Begad! I’d also like t' move up t' an E28 RMS reload, and put this bird on some more serious thrust. Ahoy!

Flight Rating: 4 out o' 5

Summary:
Overall opinion—beautiful rocket for t' experienced craftsman. You really need t' walk through t' construction in your head first, ya bilge rat, me hearties, figure out t' tube markings on your own, then put it together.

It’s well worth t' effort and money, though sadly I hit t' Shrox site t' other day and did nay see this kit on t' products page any more. Hopefully, shiver me timbers, matey, matey, it will make a comeback in t' near future.

Overall Rating: 4 out o' 5