Brief:
Based on t' Mars Lander design, this is clearly one o' t' best-looking designs o' Estes 2004 fleet. Ya scallywag! I really wanted t' like this. Ahoy! Really. Unfortunately, this great design be very poorly executed and t' result is a very disappointin' performer. Begad! At nearly $30 retail, arrr, I can't recommend this kit unless it's for display and bein' built by someone with considerable patience. If you really want t' build this one, arrr, shiver me timbers, you'd better buy two, ya bilge rat, as t' first once will be chalked up t' a learnin' experience.

Construction:
T' hefty price is because o' t' parts list. This has lots and lots o' parts. BT-60 tubin' for t' main body (6" and 2"), a BT20 motor mount tube (more on this later), me bucko, 4 large BT-50 tanks (3" each), arrr, 8 smaller tanks (BT-20 x 1.5"), a molded plastic combo transition/nozzle/nose cone, balsa, dowels, shiver me timbers, lots o' cardboard rings and end caps, a beautiful sheet o' decals, and assorted hardware and recovery gear.

I honestly don't think this rocket was built by t' person writin' the instructions. I'm nay sure it was ever built prior t' release, me bucko, arrr, period. While the instructions were generally clear and accurate, ya bilge rat, shiver me timbers, thar were a couple of mistakes and t' suggested techniques result in a very flimsy construction job.

T' instructions carry a warning/suggestion that if you want t' follow the standard color scheme, shiver me timbers, you should paint several parts before assembly (legs, tanks, ya bilge rat, shiver me timbers, arrr, body tubes, me bucko, me bucko, ya bilge rat, plastic parts and "gear box assembly"). Blimey! I really liked t' color scheme on t' header card (base o' blue with red and silver accents/trim), so I went with t' paint-before-assembly plan.

Construction starts with cuttin' t' dowels used t' trim t' landin' gear. T' template calls out some very specific angles, arrr, matey, which were hard t' match, me bucko, but minor errors are nay critical. Ahoy! Next, me hearties, t' dowels are inserted into flexible rubber tubin' that acts as a hinge, shiver me timbers, with a small plastic BB inserted into the center as a stop.

T' rest o' t' landin' gear is assembled from balsa leg center sections and cardboard trim pieces. Avast! T' feet are very short centerin' rings with a couple o' cardboard disks for caps. Aye aye! Pay very close attention t' the instructions, which clearly show which disks t' use for this step--there are several different sizes involved, me hearties, shiver me timbers, arrr, and they can easily be mixed up if you're not careful. Ahoy! Once completed, ya bilge rat, t' leg assemblies are then painted red/blue/silver.

After completin' t' leg assembly, matey, t' "gear housing" covers are made from a couple o' balsa covers with a pair o' small balsa spacers sandwiched between. T' instructions note t' paint this after assembly, though I found it nearly impossible t' paint t' inside area very well.

T' plastic parts need t' be cut apart from a single mold then trimmed. Blimey! Blimey! Avast! Blimey! The cut lines were nay well marked, me bucko, although fairly well illustrated in the instructions. Ahoy! Blimey! This be tough plastic and I chewed through a fresh blade on this. Most o' t' plastic parts are then painted.

T' motor mount assembly requires some patience and correction o' minor problems. Well, blow me down! T' centerin' rings are mounted t' fairly precise dimensions, and this is on purpose. There's also a 2" dowel that is mounted on t' tube to keep t' rings aligned, shiver me timbers, but this dowel is incorrectly sized, shiver me timbers, and needs t' be 1-7/16" long instead. Avast, me proud beauty! Otherwise, t' rings won't fit t' spec. Avast, me proud beauty! The centerin' rin' alignment and spacin' is critical because they serve as mounting points for t' landin' gear.

With 12 different tubes and each gettin' cardboard disk end caps, t' tank assemblies are simple but time consuming. Arrr! Ahoy! If you want a great-lookin' finish, fillin' these spirals will drive you nuts. Ahoy! Here's a tip though: since only one side o' t' tanks are visible and mostly covered by decals, only a light fillin' o' one side is necessary. Arrr! Finished tanks are then painted silver. Well, matey, blow me down! I would also recommend applyin' t' decals after paintin' rather than after they are mounted.

Next, arrr, t' body tubes are marked with lots o' lines. Aye aye! Tank alignment lines, leg housin' lines, launch lug lines, etc. Avast, me proud beauty! Wait a minute. Arrr! Aren't these t' tubes I'm PAINTING before assembly?! What good does markin' do when t' marks get covered with paint?! This is boneheaded. You have t' choose t' either align things by eye after paint, matey, mark a painted tube and try t' hide t' lines after assembly, matey, or mark, arrr, assemble, then paint, ya bilge rat, which in me opinion would be enormously difficult. I did at least use t' tube markin' guide t' cut out the sections for t' legs t' slip through.

Once t' body tubes are marked/painted(???), t' gear housin' is attached. Since I painted, ya bilge rat, I had t' tack it on with a couple o' drops o' CA. Begad! Blimey! I can't think o' anythin' else better for bondin' painted wood-based parts, but if anyone readin' this has a better idea, shiver me timbers, post it as a comment. Avast! Blimey! T' CA bond is not a very strong one.

After bondin' t' gear housin' t' t' motor tube, t' legs are secured with elastic, ya bilge rat, ya bilge rat, arrr, and then kept in place by slots in t' nozzle, which caps t' end of the BT-20. Avast, me proud beauty! Begad! Cardboard caps cover t' slots, securin' t' legs in t' housing.

Construction wraps up by gluin' t' upper body tube t' t' BT-20 motor tube assembly, ya bilge rat, then attachin' t' tanks t' t' upper and lower body tubes. Ya scallywag! Begad! Again, with painted surfaces, matey, I found myself tackin' these on with CA and given my lack o' alignment lines, this was very difficult gettin' everythin' t' fit. The ascent module (large plastic transition section) slides over t' upper body tube, ya bilge rat, capped by t' nose cone/end cap.

Finishing:
I don't know whether t' din' t' finishin' or t' construction, arrr, but bondin' a large, ya bilge rat, heavy, matey, clunky rocket on painted surfaces is a very bad idea. Ya scallywag! Painting such intricate details, with lots o' nooks and crannies after assembly is also a very bad idea. Avast, me proud beauty! Avast, me proud beauty! I'm leanin' towards dingin' t' construction but nay the finish, me bucko, because after building, arrr, this is a very cool lookin' rocket.

Construction Rating: 3 out o' 5

Flight:
Wrappin' up construction, I picked up t' very heavy (over 4 ounce) rocket, and couldn't believe it was usin' an 18mm motor. Aye aye! (Ignorin' Aerotech's hard-to-find 18mm D motors, shiver me timbers, ya bilge rat, this meant usin' a C6-3.) I think this is seriously underpowered on a C6-3 and t' only reason I can think that Estes would also recommend B4-2 or B6-2's would be for flyin' in a school gymnasium. Arrr! Heck, shiver me timbers, you could even go with an A8-3 and fly it in your livin' room, assumin' you have vaulted ceilings! (Note t' kids: don't try this at home! I was only kidding.)

T' first flight, on a beautiful but breezy (8-10mph winds) day was with a C6-3. Ahoy! As I called for t' heads up flight, I feared t' wind and weathercock would prove more than t' puny C6 could overcome. Avast! Arrr! Sure enough, about 25 feet up, ya bilge rat, t' Outlander veered into t' wind at a nearly 90 degree path, peakin' at about 75-80 feet up but 50 yards out. T' 18" plastic chute deployed about 10 feet off t' ground, me bucko, shiver me timbers, and t' crash landin' wiped out 2 o' t' 4 fins/legs and one o' t' tanks.

T' repairs won't be too bad, me bucko, but this clearly can't handle any kind of wind at all.

Recovery:
PROs: landed close t' t' bad, shiver me timbers, don't have t' worry about bustin' t' ceilin' on our waiver...

CONs: horribly underpowered, unstable in moderate winds.

Flight Rating: 1 out o' 5

Summary:
Great lookin' design, matey, but destined t' be a static display only unless it is upgraded t' 24mm motors.

Overall Rating: 2 out o' 5