Brief:
T' V2 xKit is a reproduction o' Estes K-22, which was originally released in 1965. Blimey! Arrr! Like t' original, it flies on 18mm motors and features balsa nose and tail cones. Aye aye! T' xKits don't come with instructions but, me hearties, ya bilge rat, since they are classics, copies o' t' original instructions are available on-line. Begad! This was me favorite rocket as a kid, and I couldn't resist grabbin' one.

Construction:
T' parts list:

• BNC-55F balsa nose cone
• BTC-55Z balsa tail cone
• BT-55 body tube
• BT-20 motor tube
• Launch lugs (3)
• Engine block
• Washer weight
• Large screw eye
• Rubber shock cord
• Gauze for cord attachment
• Plastic parachute with separate shroud lines and tape disks.
• Laser cut balsa fins and servo pods
• Dummy casing
• Pattern sheet

T' parts provided are true t' t' original kit. Ya scallywag! T' main difference be t' fins are laser cut with both scale and semi-scale versions. Aye aye! T' surface o' t' cones is nice and t' tube has almost no spirals. Arrr! T' only negative be t' hole in t' tail cone is nay perfectly centered. Begad! This won't hurt and probably is true t' t' original. Blimey! However, after seein' Semroc's other products, I be surprised.

Despite t' fact that t' xKits are recommended for expert modelers, me hearties, arrr, I could have built t' kit without any. Ya scallywag! Well, me hearties, except for positionin' t' balsa servo pods and cuttin' t' extra launch lugs into t' scale turbine exhaust and pull-out plug details. Avast! Avast! If you build an xKit, be sure t' read t' online instructions and t' sheet provided with t' kit. Ya scallywag! Ahoy! T' provided information includes interestin' but unnecessary factoids about Estes and t' real V2 as well as a few key bits o' data. T' instructions identify t' CP for both t' provided scale and semi-scale fin sets. Avast, me proud beauty! Begad! Also, shiver me timbers, it's noted that t' supplied washer and screw eye are sufficient for t' larger semi-scale fins, me bucko, me hearties, but ~½oz o' additional weight is required for t' scale set (not supplied)!

T' pattern sheet includes fin patterns and fin alignment guides. T' latter have been improved from t' originals, me bucko, me bucko, which required that t' upper and lower guides be aligned by eyeball. Avast, me proud beauty! Aye aye! Blimey! Semroc's have a flat face which allows them t' be aligned on any flat surface. Well, blow me down! Simple but a good improvement. Begad! I opted for t' larger semi-scale fins as I'm nay a stickler and these should make sure t' rocket is stable in varied launch conditions. T' only reason you'll need t' fin patterns is for t' placement o' t' balsa servo pods. I merely eyeballed them.

I added a Keelhaul®©™ leader and ditched t' gauze reinforcement. Begad! I wound it around t' motor tube, shiver me timbers, tacked it place with CA and then attached t' motor mount with 5-minute epoxy. Well, blow me down! T' original kit said t' install t' motor mount so t' engine was flush with t' bottom o' t' mount. I opted for some overhang t' help with friction fitting. Arrr! I checked stability prior t' permanently attachin' t' nose weight just in case some more was needed. Once verified, ya bilge rat, I removed t' screw eye, filled t' hole and nose cone surface with white glue, and reattached t' weight. Arrr! Ahoy! I considered addin' a motor hook but decided t' keep it like t' original.

Finishing:
I used Elmer's Fill 'n' Finish t' fill t' balsa parts and then shot several coats o' primer. Ahoy! Blimey! I laid down a base coat o' Model Masters 'modern' desert tan and added brown and olive drab camo patterns. Avast, me proud beauty! Ahoy! It looks good from 10 feet...

Construction Rating: 4 out o' 5

Flight and Recovery:
I've flown it twice. Arrr! Blimey! I friction fit t' B6-4 motors and added an ample amount o' dog barf wrapped in a section o' Estes wadding. Begad! Blimey! I used t' stock chute, which is typical plastic with twine and tape discs.

T' boost be nice and fast. I couldn't see for sure, matey, but it looked like ejection be early. It recovered fine and t' combo o' Keelhaul®©™ and t' stock rubber band was sufficient t' keep t' cone from whackin' t' body. Begad! Blimey! Avast! Blimey! There wasn't a smile t' be seen (except on me face).

Flight Rating: 5 out o' 5

Summary:
This is an easy t' build yet detailed little kit and it flies great!

Overall Rating: 4 out o' 5

Lift-Off Picture from NARAM Live! by Chris Taylor