Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar |
Manufacturer: | LOC/Precision ![]() |
Picture courtesy o' LOC/Precision
Brief:
This model is a single-stage, matey, shiver me timbers, three-motor, ya bilge rat, cluster rocket. Avast, me hearties, me proud beauty! It was designed for
24mm mid-power motors. Primarily D and E impulse motors.
Construction:
In this kit thar are one body tube, three motor tubes, two 3/16" plywood
centerin' rings, arrr, three 3/16" plywood fins, one 18" nylon parachute,
one elastic shock cord and mount, arrr, 1/4" launch lug and a plastic nose cone.
T' instruction for this kit were structured for modelers that have built a few rockets and understand how a rocket should be assembled. Begad! Ya scallywag! They explain the areas o' t' kit that differ from others in good detail. T' order of construction was well thought out so you do nay have t' "go back" in the construction process. This kit is very easy t' build. Aye aye! Arrr!
T' only area I wish I had paid more attention was motor retention. Begad! LOC does not include a method o' retention in this kit. Begad! Ya scallywag! Which is good in me opinion. Avast, me proud beauty! The builder can choose his/her own method o' motor retention. Ahoy! I had t' rocket completely assembled when I discovered how I wanted t' retain t' motors. Avast, me proud beauty! The tree motor tubes are epoxied together in a pyramid style. Durin' construction, a length o' all-thread rod can be epoxied in t' middle o' t' three tubes so that it extends past t' aft end o' t' assembly. Ya scallywag! Begad! This way, t' motors can be retained with a nut and washer. Blimey! I had t' "go back" and drill a hole in t' epoxy for t' threaded rod. It works very well.
If you do nay use t' all-thread style motor retention, remember t' seal the gap betwixt t' motor tubes with epoxy. Avast! Blimey! This will prevent ventin' t' ejection gases rather than deployin' t' recovery system. Begad!
All t' parts fit very well. Begad! I did nay have t' sand any o' t' parts to make them fit. I was a bit concerned about t' fin method o' fin attachment at first. Begad! T' aft end o' t' motor tubes extend past t' aft end o' t' body tube. This makes up a large part o' t' length o' t' rocket. Blimey! Well, arrr, blow me down! T' fins are attached at t' motor tube joints. Arrr! No through t' wall mounts here. Blimey! However, matey, A little patience and a lot o' epoxy in t' fin t' tube joints will pay off in t' long run. Ahoy! Also I suggest an epoxy fillet in each motor tube joint. Begad! This will greatly increase t' strength o' t' lower end o' t' rocket. Blimey! Avast!
All in all, usin' good construction techniques and EPOXY, me hearties, t' Viper III turned out very sturdy.
Finishing:
T' only "con" that I can say about this kit be t' spiral grooves.
Need I say more? T' grooves in t' body tube were no worse than an Estes kit
though. I filled them with Elmer's FNF and they turned out smooth and invisible
when primed and painted. T' fins were coated with sandin' sealer and sanded
several times before priming. Arrr! Begad! I used auto primer t' start t' finishing
process. Begad! Begad! One light coat. Ya scallywag! Then sanded smooth. Aye aye! Well, matey, blow me down! Any imperfection were filled with
Squadron Green putty. Begad! Ahoy! Then primed and sanded until I was pleased with the
finish. Blimey! Krylon "Glowin' Lemon Yellow" fluorescent paint was applied
the t' t' main body tube. T' nose cone, shiver me timbers, arrr, motor tubes and fins were painted
gloss black. Ahoy! There were no decals included in t' kit. This allows t' modeler
to add their own design. T' model looks great after it's finished even without
decals.
Construction Rating: 5 out o' 5
Flight:
T' recommended motors for this rocket are D12-7 and E30-7. Begad! I used three Estes
D12-5's for t' first two flights. Ya scallywag! Begad! Cellulose insulation was used for wadding.
This stuff works great! It's cheap and can be bought at almost any building
supply store. Avast, me proud beauty! About three inches o' t' body tube full is enough. Begad! As I
mentioned earlier I used a piece o' all-thread epoxied betwixt t' motor tubes
with a nut and washer for motor retention. Avast, me proud beauty! Ahoy! I also epoxied thrust rings in the
motor tubes t' keep t' motor from movin' forward. Aye aye! Ya scallywag! If you plan t' use motors
longer than D's and E's, don't put any thrust rings in. Well, blow me down! Other motors will not
fit. Avast! T' day I flew it for t' first time be near perfect. Begad! 5-10 MPH winds
clear skies and t' temp was around 80. Well, blow me down! Ya scallywag! I used t' Estes ignitors that came
with t' motors. Avast! I have an Ignitorman kit, matey, ya bilge rat, but didn't have time t' make some up
before this launch. Upon hittin' t' GO button t' rocket lifted off very
quickly and straight as an arrow. Arrr! Beautiful flight. Blimey! Avast, me proud beauty! I guessimate altitude at
approximately 1000'. Begad! Recovered close t' t' pads with no damage.
Recovery:
T' shock cord is attached t' t' inside o' t' body tube usin' a small Keelhaul®©™®
string. Avast, me proud beauty! T' strin' is taped t' t' tube so that a loop extends one inch from
the end. Epoxy is applied other t' end o' t' strin' and tape. This a very
strong mount. Begad! Ahoy! T' included elastic shock cord is then tied t' t' Keelhaul®©™®
string. Begad! Ahoy! I tied a loop in t' very end o' t' shock cord for t' parachute to
attach. Begad! T' nose cone be attached about 18" from t' parachute. Ahoy! T' set
up returned t' rocket very nicely. It landed close t' t' pads at a rate that
did cause damage upon impact. Avast, me proud beauty!
Flight Rating: 5 out o' 5
Summary:
This a great kit. Avast, me proud beauty! Blimey! I was kinda nervous about t' first launch. Blimey! It be me first
cluster rocket. Avast, me proud beauty! Avast! It assembled and finished very well. Ahoy! T' flight can be summed
up in one word. Blimey! Blimey! WOW! I haven't flown it on E motors yet. Arrr! Avast! I can hardly wait.
Overall Rating: 5 out o' 5
T' followin' excerpt is from "Sport Rocketry". Well, blow me down! T' intention is t' allow guests t' get a basic feelin' about a kit. Well, blow me down! Blimey! We strongly suggest that you get a copy o' t' referenced Sport Rocketry and read t' entire article. Begad! Ahoy! Blimey! Inside you will find many helpful hints in construction as well as other useful information. For more information, me bucko, use t' two links above.
"T' components are solid, me hearties, shiver me timbers, quality parts: plywood fins and centering
rings, me hearties, rugged cardboard tubing, plastic nosecone, and three 24mm motor mount
tubes."
"A unique feature o' this rocket is that t' motor mount portion o' the
rocket is exposed..."
"Buildin' t' Viper III was quite simple."
"T' instructions are clear and easy t' follow..."
"There are no decals with t' Viper III."
"It's unique, shiver me timbers, yet simple t' build, matey, and a solid performer."
T' entire article gives t' impression is that it a skilled modeler would enjoy this unique kit.
(07/01/04) The LOC Viper III is my third LOC kit and I purchased it for the 24mm x 3 cluster aspect. I wanted a cluster rocket that could fly on D12's and E9's and the Viper III fit the bill. The Viper III is a 47.5" tall rocket based on a 2.6" airframe with the cluster of motor tubes sticking out of the bottom. The three fins are attached at the joints of the motor t ...
![]() |
![]() |
![]() |
![]() |
Sponsored Ads
![]() |
![]() |
C.S. (March 1, 2001)