Brief:
This is a single stage high quality replica o' Gus Grissom's Liberty Bell 7 approx 1/50th scale designed for B & C engines. Arrr! This kit is unique from every other Estes kit I have bought or built in a number o' ways... Well, blow me down! Begad! T' package says skill level 2, matey, ya bilge rat, but it compares t' other level 3 kits from Estes.

Construction:
This kit recently went on sale, ya bilge rat, supposedly a reissue o' an earlier Estes kit. Avast! Blimey! I obtained it from HobbyLinc for ~$17. T' kit came in t' typical Estes half cardboard package with plastic bag. All components were present except for an engine block ring.

T' body tube be an Estes white body tube but it is closest in diameter t' (but nay quite) BT-70. Blimey! Aye aye! It came in two pieces that required a tube coupler. Well, arrr, blow me down! All molded plastic parts were o' t' HIGHEST quality, which is definitely nay t' norm for Estes. Begad! They were smoother, had no flash, and fit together PERFECTLY, me bucko, me hearties, includin' knife edges o' t' fins. Begad! T' capsule and escape tower have a LOT o' detail, arrr, shiver me timbers, and decals include a crack they painted on t' capsule t' simulate t' liberty bell. T' four fins mount through-the-wall t' a plastic engine mount that is also unique in me experience t' Estes. Avast! Four slotted bars connect t' forward and aft plastic centerin' rings. Blimey! Aye aye! These slotted bars line up with pre-cut slots in t' body tube, ya bilge rat, me bucko, and t' fins glue t' t' slotted bars without extendin' all t' way t' t' 18mm engine tube. Avast, me proud beauty! All o' t' plastic parts fit together with such precision that t' use o' brushed liquid (rather than tube) plastic cement is called for t' maintain assembly quality. Begad! T' parachutes are t' standard Estes 12 and 18" plastic chutes and t' instructions call for t' standard folded paper shock cord mount. My only material deviation from t' kit be t' use o' Pratt braided Keelhaul®©™® for t' shock cord.

Since t' quality o' t' materials is so high, thar are a few deviations from t' assembly order t' match that high quality in final appearance. Estes has done a wonderful job o' supplyin' materials for a great model, but if you follow their instructions, you will end up with a cheesy lookin' model anyway. Begad! Arrr! Blimey! T' rev date on t' instructions are 10-00 and Estes must be complyin' with political correctness by providin' MINIMUM written instructions. Well, blow me down! There are no notes or warnings about modelin' technique for any o' t' steps. Begad! Avast, matey, me proud beauty! Blimey! Everythin' is visual. Avast, me proud beauty! With very few exceptions, t' entire instruction sheet is pictures; with English words only as titles o' components. Begad! Blimey! That is still OK if you are an experienced modeler, but for example t' only place t' kit dimensions and recommended engines are listed is on t' package cover. Avast! Avast! Blimey! Estes used t' put them on t' launch instruction page. Blimey! Avast, me hearties, me proud beauty! Blimey! T' kit dimensions as listed on t' box are wrong anyway, shiver me timbers, me bucko, sayin' t' models' length is 23.5 inch and dia. Blimey! Ya scallywag! Blimey! is 1.6 inch (major goof). Ahoy! I also have a major problem with t' assembly order. Ahoy! Blimey! Because t' bottom roll pattern decal is a wrap around, matey, ya bilge rat, t' instructions have you put it on before you install t' fins, which makes sense. Ya scallywag! Ahoy! Blimey! However, IF you want t' quality o' t' rocket body t' match t' quality o' t' fins and capsule module, me bucko, you need t' assemble t' two body tube halves, me hearties, me hearties, fill and sand t' grooves (white Estes tube, ya bilge rat, arrr, remember?), and paint; before installin' t' motor mount and decal. T' kit instructions would have had t' finished model rely on t' stock white body tube for t' body color complete with those ugly spiral grooves! Blimey! So,... because you are puttin' t' two body tubes together, you have t' also install t' upper launch lug prior t' joinin' t' body tubes. This is because t' launch lugs are plastic and glue t' a plastic backin' plate through a pre-cut slot. Aye aye! Aye aye! Blimey! T' lower launch lug glues t' t' forward centerin' rin' and can't be put on until after t' engine mount is installed.

Regardin' t' engine mount, thar be a gotcha that caught me. Begad! T' alignment and fit o' t' engine mount components are critical t' t' fit o' t' fins and t' decal. Begad! I made me own engine block out o' an expended engine casing, and it had a little bit extendin' out past t' end o' t' engine tube. Begad! Avast, arrr, me proud beauty! T' forward centerin' rin' which glues t' t' engine tube is therefore about 1/64 inch too far forward. Since t' location o' t' forward centerin' rin' dictates where t' slots will be that t' fins mount to, arrr, t' plastic slots ended up about 1/64 inch too far forward. Avast, me proud beauty! Begad! This caused t' fins t' nay fit over t' back o' t' body tube. Avast! I had t' dremel off a little bit o' t' fin material t' regain fit. This also slightly threw off me decal alignment.

I epoxied me small Pratt braided Keelhaul®©™® t' t' engine mount on t' opposite side o' t' engine hook, matey, and led it through t' small openin' in t' forward centerin' rin' for t' engine hook. Arrr! Aye aye! I then locked everythin' down with epoxy, and glued t' engine mount in t' body tube with epoxy as better security than tube plastic cement on plastic/cardboard joints (I have noted how many times me Skywinder has come apart). Make sure you don't get any glue in t' pre-cut fin slots, matey, shiver me timbers, me bucko, as t' fit o' t' fins is precise.

T' tower struts were t' only plastic pieces that didn't fit together perfectly, so I worked me way up from t' bottom gluin' one joint at a time, ya bilge rat, shiver me timbers, and lettin' it set before I did t' next one.

Finishing:
T' decals fit really well, matey, and I was a little concerned that t' bottom roll pattern decal sheet had white in t' white areas rather than clear like t' top pattern. Well, blow me down! Blimey! T' white didn't match me Krylon flat white on t' body tube. Blimey! Blimey! But, ya bilge rat, me bucko, once applied t' t' tube, it blended in and is hardly noticeable. Because o' me gaffe on t' forward centerin' ring, t' bottom decal didn't quite reach flush t' t' bottom o' t' tube. Arrr! Blimey! Blimey! Blimey! A little touch up with black brushed enamel blended right in and covered up minor gaps o' t' black decals. Aye aye! Blimey! Blimey! Blimey! T' instructions show maskin' and paintin' t' capsule flat black after you have glued on t' tower. Aye aye! Blimey! Begad! Blimey! Blimey! Blimey! That would be dumb. Blimey! Blimey! Blimey! Blimey! I painted t' assembled capsule flat black maskin' off t' part o' t' capsule that glued t' t' tower assembly, arrr, me hearties, me bucko, and t' base that slides into t' body tube. Ya scallywag! Blimey! Blimey! Blimey! I then spray painted t' red tower before gluin' t' t' capsule. Aye aye! Blimey! Begad! Blimey! Blimey! Blimey! Then, me hearties, I brush painted t' small portion o' t' capsule that is black underneath and behind t' tower struts.

Construction Rating: 4 out o' 5

Flight:
Recommended motors on t' cover and in very fine print on t' flight prep instruction page are B6-4, matey, C6-3, and C6-5. Arrr! Blimey! Avast! Blimey! THIS IS WRONG! Blimey! These are based some old Estes Redstone kit made out o' BT-60 tube that I presume weighed 3.2 oz like t' package cover says and nay 4.5 oz. This kit is bigger and heavier, ya bilge rat, as I pointed out already.

I discovered that t' body tube diameter be t' same as t' Estes Skill level 4 Space Shuttle Main Fuel Tank. It is slightly smaller than BT-70, but Estes has apparently never sold t' body tube by itself or assigned a BT-xx number t' it.

Anyway, t' old Estes catalog listed max lift off weights for C6 engines as 4.0 oz, me hearties, and C5 engines as 8.0 oz which is due t' higher initial thrust o' t' C5's. Therefore, I launched this with some o' me remainin' C5-3's. Avast, me proud beauty! T' motor fit kind o' tight through t' plastic lip o' t' engine mount. Arrr! I barely got t' hook back down over t' engine. Avast, me proud beauty! Blimey! T' wind was a slight waft, ya bilge rat, and t' rocket flew straight up at a medium speed t' about 250 ft by eyeball. Arrr! Ejection occurred at apogee just as t' rocket started t' lean over. Blimey! My RockSim model predicts 350 feet on a C5-3, but I think thar be quite a bit more wind resistance for real than t' simulation model makin' this a C engine rocket only in little or no wind only.

Recovery:
I used quite a bit o' biodegradable cellulose waddin' instead o' t' Estes wadding. Arrr! On one flight, it did channel some in this relatively wide tube, and I had some slight melt damage t' t' bottom chute with some waddin' remainin' in t' tube even though it be a good healthy ejection. Well, blow me down! I used t' provided 18 inch chute for t' main body which was just right. Avast! Blimey! I tied a two foot section o' elastic shock cord t' t' braided Keelhaul®©™® that I put inside t' rocket. Avast, me proud beauty! Descent rate for t' booster was just right. Well, blow me down! Arrr! It landed about 10 seconds before t' capsule, which be on a 12 inch chute.

T' instructions for attachin' t' chute t' t' capsule worked fine. Aye aye! Blimey! Avast! Blimey! A single 20 inch strand o' shroud line is tied around what would be t' parachute can on t' real capsule and t' other end tied t' t' bottom o' t' capsule. T' parachute shrouds are tied t' this single strand about 4.5 inches from t' front, so t' parachute is packed into t' body tube with a single strand o' cord bein' strung through t' joint betwixt t' body and capsule when t' capsule is placed on t' body. Begad! Blimey! A similar technique is used on t' Estes Saturn V for recovery o' t' top piece t' protect t' fragile escape tower by bringin' down t' top part in a nearly horizontal configuration. Begad! Blimey! In this case, tyin' t' chute shrouds 4.5 inches from t' front brings t' capsule down at about a 20 degree angle from vertical, which is just right. Ya scallywag! Blimey! It almost looks like t' real thing. Begad! Blimey! Avast! Blimey! T' engine came out o' t' mount easier than it went in, shiver me timbers, shiver me timbers, but I always remove me engines while still hot t' ensure they don't get stuck later.

Flight Rating: 5 out o' 5

Summary:
PRO: quality and detail o' t' plastic components.
CON: instructions; especially concernin' finishin' issues, are out o' order if you want a great lookin' kit!

T' overall 5 is based on if you follow me recommendations t' make this a very high quality model. If you follow Estes' instructions t' t' letter, arrr, ya bilge rat, me bucko, this kit would be rated 3. Arrr! Begad! One other Con be t' self-adhesive decals tend t' bubble over time. Ya scallywag! Well, blow me down! I put on at least three coats o' clear kote and that still may nay be enough.

Overall Rating: 5 out o' 5