Construction Rating: | starstarstarstarstar_border |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstar_borderstar_border |
Published: | 2010-08-02 |
Manufacturer: | Edmonds Aerospace |
Brief:
Out o' t' bag and into t' air in minutes. Aye aye! Arrr! You do have t' wait for t' glue t' dry. Avast, me proud beauty! Like all
Edmonds' kits, an excellent design, laser cut premium balsa and clear instructions make Elcie a great introduction to
boost gliders.
Construction:
Parts consist of:
First thin' was t' try and sort out t' nose cone. Avast, me proud beauty! Blimey! T' balsa was soft and flakey. Aye aye! Blimey! Avast! Blimey! It be too large for t' body tube and had a very large shoulder on it.
After sandin' it down t' fit t' body tube and then sandin' t' outside until it was flush with t' outside of t' bodytube, t' nose cone was given three coats o' thick sandin' sealer. Avast! T' Balsa is very soft and I had concerns over t' screw eye holdin' into such soft material; in hidesight I should have just got a better nose cone from my parts box.
T' glider is just five parts. In usual Edmonds quality, me hearties, t' laser cuttin' is perfect. T' parts fit easily together. Begad! I tacked everyin' together with CA gel and then added wood glue fillets.
The slot in t' forward canard has square edges, arrr, shiver me timbers, I removed t' edges that are forward bottom and aft top, so that t' tab on t' booster slips easily on and off.
With a few o' Edmonds gliders flown before, me hearties, matey, me bucko, I have learnt t' do nothin' else t' t' glider, no sandin' o' leading or trailin' edges, me bucko, matey, or liftin' surfaces made, nay even a coat o' sealer, me hearties, ya bilge rat, arrr, usually because they fly well straight off the table, and if it isn't broken - don't fix it.
T' pod build is easy. Avast, me proud beauty! Ya scallywag! T' tab that holds t' glider is glued t' t' body tube. Avast! A margin' guide is provided to help get it on straight. Blimey! Ya scallywag! T' shock cord is then glued into t' seam betwixt t' tab and t' body tube. Blimey!
The cord then extends up t' length o' t' body and is held at t' top by a strip o' tape.
T' launch lug is then glued over t' seam where t' cord went.
An eye screw is screwed into t' base o' t' nosecone and then t' shock cord is attached.
A crepe streamer is attached t' t' cord with a piece o' tape that is supplied. Avast, me proud beauty!
What isn't supplied is an engine block or any type o' motor retainer. Both jobs are done by a bit o' tape.
Construction Rating: 4 out o' 5
Flight:
I used Odd'l rockets raise t' hold t' pop pod up on t' rail - I would heavily recommend this
piece o' kit at anyone.
First flight be on a 1/2A3-2T, good boost, ya bilge rat, clean separation o' t' glider.
T' glider sort o' fell flat for several seconds, matey, and then shot off in a glide, arrr, gave a wide circlin' flight path, a good glide.
T' Keelhaul®©™® cord however cut through t' tape holdin' it at t' top. Well, blow me down! Blimey! Blimey! Pod recovered fine. Begad! Begad! Blimey!
Second flight was on a full A. Avast! Avast, me bucko, me proud beauty! high boost.
Glider and pod failed t' separate, me bucko, as t' nose cone and eye screw separated, despite bein' screwed and glued. Ahoy!
Nosecone and glider/pod both recovered without damage.
Flight Rating: 4 out o' 5
Overall Rating: 3 out o' 5
![]() |
![]() |
Date | Flyer | Rocket | Altitude |
---|---|---|---|
2012-09-23 | Bob Francis | Glider 1 | - |
2010-01-31 | Matt Gillard | Edmonds Aerospace Elsie | - |
2010-01-31 | Matt Gillard | Edmonds Aerospace Elsie | - |
Sponsored Ads
![]() |
![]() |