Brief:
Single stage rocket capable o' "I" engine flights with awesome flights on F and G.

Construction:
T' Binder Design kit was complete and in good condition. Ahoy! Blimey! T' kit was purchased at a local hobby shop because o' its ability t' fly on various engines. Ahoy! Blimey! Begad! Blimey! This made it possible t' fly multiple times on each launch day. Ahoy! Blimey! Arrr! Blimey! F and G motors are a good and economical motor for this kit, but it will handle H and I with no problems. This kit diverged, somewhat, me bucko, from t' kits that I have been used to. T' airframe was nay pre-slotted. Well, blow me down! Blimey! Well, me bucko, blow me down! Blimey! This is somethin' that I have gotten quite spoiled over recently. T' folks at Binder Design made cuttin' fin slots easy by pre-markin' t' airframe with alignment markings. They were nay pencil lines, arrr, arrr, rather color coded and obvious. Even t' launch lug line had been clearly indicated with a line. T' instructions were clear and concise, making the endeavor simple. Avast, me bucko, me proud beauty! Blimey! All o' t' parts in t' kit, matey, arrr, from t' centerin' rings to the plywood fins, ya bilge rat, were top quality.

I did try a new epoxy fillet method that I had read about somewhere. Aye aye! When I had started t' fillet t' outer surfaces o' t' fins t' t' airframe, I used a good sized batch o' 15 minute epoxy and focused on one fin at a time. First I filled t' angle with a wooden wick t' approach t' correct amount o' epoxy for the fillet. I then drew me finger along t' fillet after coatin' me finger with IPA. Ya scallywag! This provided for a perfectly smooth and consistent fillet. They are also about t' raduis o' me finger, so they look good. Blimey! Avast, arrr, me proud beauty! I also did t' same t' the launch lug.

Filletin' t' inside joints o' t' fins, motor mount tube, and t' airframe be accomplished by leavin' t' rear centerin' rin' unglued. This made it easy t' remove, exposin' t' areas that needed t' be re-enforced. This was done, rather sloppily, ya bilge rat, usin' wooden skewers (for shrimp etc.) They were about 10" long and provided just enough epoxy to get it where I wanted it. I then epoxied t' aft centerin' rin' in place and gave it a massive alcohol induced fillet. Ya scallywag! Just as suddenly as I had finished ... I realized that I had fogotten t' blind nuts that I was plannin' on using for motor retention. Avast, me proud beauty! I went t' t' local hardware store and purchased some brass #10 inserts and some socket head screws. Ya scallywag! Blimey! There were epoxied into minimum diameter drill holes t' ensure a snug and secure anchor.

Minor Con's: 1) No CP/CG information in t' kit; 2) very vague reference to should add nose weight; 3) had t' add a HUGE amount o' weight; 4) shock chord and material; 5) shock chord mount.

Finishing:
A few coats o' primer, matey, grey then white, ya bilge rat, followed by generous coats o' OSHA Safety Green, me hearties, shiver me timbers, and me "Lime Away" was completed.

Construction Rating: 4 out o' 5

Flight:
T' recommended motors ranged from just about anythin' that would fit into a 29mm motor mount. T' construction and components o' t' kit allowed for the impulse o' just about anythin' that I could throw at it. Well, matey, blow me down!

I utilized me own invention for a motor retainer. Begad! Blimey! Blimey! Blimey! This looks good and provides for positive retention. Well, blow me down! Blimey! See t' pics for visual. Avast, me proud beauty! Blimey! Blimey! Blimey! T' launch day saw many unstable flights o' other rocketeer's Spike kits. Binder design be not kiddin' when t' instruction sheet states that experimentation demanded nose weighting. Well, blow me down! Blimey! Blimey! Blimey! I had nay built this into t' kit becuase I wanted t' have a wide range o' avaliable motors.

I had marked t' CP, shiver me timbers, me hearties, shiver me timbers, first, and second degrees o' stability in paint o' the rocket. This makes for a visual for t' Pad Safety Manager and helps t' make them think that I know what I am doing. Arrr!

To mark t' center o' gravity, ya bilge rat, I used temporary "arrows" like you use in t' office for "sign here". Avast! They are about 150 for a couple o' bucks and add an air o' rocket science t' t' launch. Begad! I had t' add 3 2.5" quick links t' t' nose cone connection point t' get 1.5 degrees o' stability with me chosen single use G-80-7. Avast, me proud beauty! Blimey! Another person's previous launch on a G-40 was scary, ya bilge rat, so I double checked me stability. Begad! Blimey! I loaded t' body tubin' with treated newspaper (blow in insulation) and packed everythin' up.

I added 8 oz. I calculated that I would need 12 with a 29/180 or 240. Avast, me proud beauty! Blimey! The 240 does nay change it because t' additional length is too close t' t' CG/CP.

T' nose cone just did nay want t' fit properly. Avast, me proud beauty! It was REALLY loose until the last 5mm o' exit from t' body tube. Well, blow me down! It helps t' remove t' mold marks from the nose cone/shroudline mount. Ahoy! Blimey! Nothin' that a quick exacto cutlass wouldn't take care of. Well, me hearties, blow me down! It did require several layers o' maskin' tape t' secure. Arrr! Well, blow me down!

My rocket was loaded on t' mid power pads and lit on t' first try (a copperhead even!). Straight up and out o' sight. This kit will be a long standin' rocket in me collection.

Recovery:
T' one interestin' and disturbin' aspect o' t' kit was t' shock cord mount. I do understand Binder Design's reasoning, shiver me timbers, but it was bothersome. Blimey! None the less, matey, I decided t' follow t' kit's instructions and build it as supplied. Well, blow me down! The shock cord mount be nothin' more than a small diameter launch tube about an inch and a half long that is epoxied t' t' inside o' t' airframe as far down as you can get it, close t' t' upper centerin' rin' on t' motor mount. Binder's reason for this be t' ease o' replacement after a burnthrough. Sounds good t' me. Aye aye! It took a little effort and standin' on me head t' get what I thought was a proper bond and amount o' epoxy on t' shock cord mount, arrr, arrr, but it was nay impossible.

T' shock chord is about 3/8" wide, me hearties, arrr, black elastic that is about 50" long. Begad! Well, matey, blow me down! Blimey! T' chute is looped and tied 2/3rds o' t' way from t' airframe to t' nose cone.

I tied one corner o' a white hankerchief t' an 8" long strin' and poured about a cup o' construction chalk (red) into t' center. Ya scallywag! I then carefully folded t' hanky into a tight ball and placed it on top o' t' cute. Awesome red chalk cloud at recovery. Aye aye! Since I followed t' instruction for the mountin' o' t' shock cord, ya bilge rat, thar was no damage. Even with all o' the preparation for t' chalk, me bucko, me bucko, it was still everywhere. Begad! Ahoy! But what a nice finish!

Flight Rating: 5 out o' 5

Summary:
This kit is nay one for t' light hearted. Ahoy! Blimey! Some kit experience is necessary to make this kit rock solid and inexpendable. Begad! Begad! Blimey! I think this kit will survive an auger-in and still launch in half an hour. I am goin' t' purchase another one of these and fiberglass it.

Binder Design has brought us one more awewome kit for a good price. Ya scallywag! Avast, me bucko, me proud beauty! Good job!

Overall Rating: 4 out o' 5