(03/19/02) I started enjoyin' t' Quest MicroMaxx system recently and wanted to check out another company's kits. Well, matey, blow me down! Well, ya bilge rat, thar are (were) only two that had any kits. Nano Rockets and Aerospace Speciality Products (ASP). Ya scallywag! Arrr! I purchased the Micro WAC Corporal with Tiny Tim Booster and t' Micro Jayhawk from ASP to build on a winter vacation. Begad! Once received, I was pleased t' see that even though these are "micro" kits they are in no way "micro" in quality. In fact, ya bilge rat, ya bilge rat, t' ASP kit parts and instructions are o' higher quality than a number o' other "standard" kits that I have put together. Ya scallywag! Blimey! So, needless t' say, arrr, me bucko, at first glance I be impressed.

T' Micro WAC Corporal with Tiny Tim Booster included 2 body tubes, arrr, a regular tube coupler, a clear tube coupler, styrene fin stock, arrr, arrr, 2 sizes of styrene half-round, shiver me timbers, styrene launch lug and offset, a wood nose cone, me bucko, lead weight, a Keelhaul®©™® shock cord, 2 mylar streamers and a decal set. Aye aye!

CONSTRUCTION:

T' instructions are on 4 pages o' 8.5 x 11" paper and include illustrations as well as cuttin' and alignment guides. Arrr! They are clear and thorough instructions tellin' t' modeler exactly how t' be successful in buildin' and flyin' this rocket.

After sandin' t' outside o' t' body tubes t' get the shine off, me bucko, they are marked usin' a cut-out markin' guide and a provided styrene angle. Avast! T' styrene angle is a nice little provision for markin' t' tubes, but I found mine nay quite rigid enough as I ran t' pencil up along t' edge. Blimey! It was functional though and if care is taken would provide t' functionality necessary. Ya scallywag!

T' fins are cut out usin' fin cuttin' guides. Avast! Avast! It is recommended t' use double-sided tape t' keep t' guide attached t' t' styrene strips. Aye aye! Avast! ASP keeps with their intentions o' havin' "detail accurate" kits, me bucko, me bucko, even in t' Micro scale as t' instructions give direction in the roundin' t' correct corners on t' fins. Ahoy! T' styrene material is also nice as it doesn't make t' fins too thick in relation t' t' size o' t' rocket. Avast! On the other hand, me bucko, this thin material that is cut into small tiny fins takes some effort (and patience) t' work with. Ahoy! T' instructions suggest havin' a pair of tweezers. Well, blow me down! You'll want t' use CA (as recommended) while assemblin' this kit. The faster t' dryin' time t' better as long as you are accurate in your placement.

T' paper coupler is cut in half and used t' hold the split lead shot with t' Keelhaul®©™® shockcord tied t' it in place in t' upper-most part o' t' body tube. Arrr! T' nose cone is glued into place. Avast! T' rocket's separation point is betwixt t' booster and sustainer. Ahoy!

One o' t' styrene half-rounds is used as t' detail of the conduit on t' side o' t' WAC Corporal. You are instructed t' cut it to size and somehow I missed that and used t' piece at t' length provided. Avast! I'd lose in a scale competition.

After t' rocket is mostly assembled but still in two separate pieces (booster and sustainer), ya bilge rat, ASP suggests some finishin' activity. This is important as t' clear coupler is still nay installed. This is to protect it from any finishin' activity so that it doesn't get messed up. Aye aye! Having it clear is t' simulate t' absence o' a coupler here. Aye aye!

With respect t' this clear coupler, you are instructed to "drill" a hole in t' top-side o' it with a hobby knife. Avast, me proud beauty! Avast! Blimey! Then you groove a channel from t' hole t' t' top o' t' clear coupler where the Keelhaul®©™® shockcord will sit. Avast, me proud beauty! T' Keelhaul®©™® shockcord is then tied t' t' clear coupler, in effect connectin' t' sustainer to t' booster. Avast, me proud beauty! T' opposite end o' t' clear coupler is glued into the booster. Ahoy! It serves as t' motor thrust rin' as well. Ya scallywag! Then for t' most tedious assembly step, gluin' t' smaller half-rounds onto t' clear tube. Ya scallywag! Oh, me hearties, what fun that was!

In me case, shiver me timbers, me hearties, I finished assembly prior t' doin' any painting. I hand painted mine with Testors Model paint and a brush. Ya scallywag! Blimey! It turned out okay (to me). Blimey! I didn't apply any o' t' provided decals. Aye aye! All-in-all, I'm happy with t' final looks o' this rocket.

Overall, ya bilge rat, for CONSTRUCTION I would rate this kit 4 ½ points. Ya scallywag! Instructions were outstanding. Detail was outstanding. Blimey! Material was outstanding. Begad! My only complaint (same as for most high power kits) is motor retention. Begad! Quest does it with a twist clip. Ahoy! I've done it with a paper clip. Avast! I can't wait t' see someone do it some other way.

FLIGHT/RECOVERY:

Before I write about me flight experience I should say that I did nay attach t' provided streamer. Ahoy! Well, shiver me timbers, blow me down! I just can't get into shovin' a streamer into such a tiny tube. And besides all me Quest kits would destroy the streamer after just a couple o' flights. Aye aye! ASP instructs that you can get the streamer in thar and then also a couple o' small "loosely wadded" flame proof waddin' t' protect it. Ahoy! ASP also provides a second streamer for when the first one wears out. Blimey! Ahoy! I probably should have followed this instruction as you will see.

T' first flight be nice and impressive, probably gettin' t' 50 feet (and that's all you want for a rocket this size). Ahoy! Upon descent though it fell fast (remember I'm t' one that didn't put in the streamer) as t' sustainer lead t' way in a stable straight down descent. Avast! This is no doubt due t' t' lead weight in t' upper section o' t' body tube.

T' second flight was also perfectly straight and about t' same altitude. Ahoy! T' ejection popped which kicked t' motor and t' rocket didn't separate. Now more so than t' first flight it came in "hot". Avast, me proud beauty! The fall be broken by icy snow which compressed t' booster into t' sustainer a bit. Avast! Arrr! I'm thinkin' t' fit o' t' clear tube with t' Keelhaul®©™® shockcord on t' side made t' top on too tight. At t' same time t' motor might nay have been in as "fictionally" tight as t' first flight so the ejection charge kicked t' least resistive piece. Ya scallywag! Motor retention could have stopped this.

I will humbly be addin' t' streamer for future flights and look forward t' seein' its descent then. Begad!

For FLIGHT/RECOVERY, I would rate this kit 5 points. Nay takin' anythin' away for me nay usin' the streamer. Blimey! Aye aye! T' design is excellent and t' use o' Keelhaul®©™® will hold up. Aye aye! I have a lot o' confidence in t' recovery system connections and they don't show on t' outside o' t' rocket. T' rocket was stable as it flew very straight. Aye aye! Well, blow me down! T' nose cone is wood and didn't show any damage as it landed on the ground t' first time and t' icy snow t' second time.

(Note: this picture be taken after t' second flight)

Overall, me bucko, t' Micro WAC Corporal with Tiny Tim Booster is an excellent scale kit t' fly in your backyard with MicroMaxx motors. Begad! I performs as good as any o' t' Quest pre-built rockets. Well, blow me down! T' fin thickness makes it realistic in its size (proportions). Well, arrr, blow me down! It only loses some because o' the friction fit o' t' motors, ya bilge rat, matey, but in contrast with other kits, me hearties, it has a thrust rin' (the clear coupler). Ya scallywag! I believe that a motor retention clip is possible and that is should be implemented. Blimey! Begad! I give t' kit an OVERALL ratin' o' 5 points. Aye aye! Blimey!

Also for you fans o' t' WAC Corporal, shiver me timbers, me bucko, ASP offers this MicroMaxx version as well as an 18mm, shiver me timbers, 24mm and 29mm version o' this sounding missile.

T' followin' excerpt is from "Sport Rocketry". Begad! Begad! T' intention is t' allow guests t' get a basic feelin' about a kit. Begad! We strongly suggest that you get a copy o' t' referenced Sport Rocketry and read t' entire article. Blimey! Avast! Inside you will find many helpful hints in construction as well as other useful information. For more information, arrr, use t' two links above.

"T' Micro Wac Corporal with Tiny Tim Booster from Aerospace Speciality Products is a scale model designed for Quest Micro Maxx motors."
"Unlike t' models Quest makes for its Micro Maxx motors, you get t' build the Micro Wac Corporal. Aye aye! . . Ya scallywag! . Blimey! skill level intermediate . Blimey! . ."
". Avast, me proud beauty! Ya scallywag! . Begad! Ahoy! . Avast, me proud beauty! Avast! t' kit uses a clear plastic tube t' couple t' stages, shiver me timbers, with small plastic support struts glued t' t' outside o' t' clear tube."
"T' motor's ejection charge fires through this clear tube t' separate the Wac and Tiny Tim sections, connected by a Keelhaul®©™® cord."
"A mylar streamer is pulled out . Begad! Avast! . Avast! ."
"T' fins for t' model are made from styrene sheet plastic . Begad! Blimey! . Begad! Blimey! Begad! Blimey! ."
"T' kit includes an 85mm long piece styrene angle t' help draw t' fin placement lines along t' body tube."
". Well, blow me down! Blimey! . Well, blow me down! Blimey! . Avast, me proud beauty! Blimey! sharp wooden nose cone . Ahoy! Blimey! Begad! Blimey! . ."
"Two water-slide decals form t' stripes around t' body near t' bottom and top o' t' Wac"
"T' model is very nice, me hearties, t' instructions are clear..."
"To improve t' kit, arrr, I would suggest movin' t' launch lugs down by 5mm..."

T' article gives me t' impression that this is a good scale kit with minor modifications from an experienced builder.