Brief:
This newest kit from Squirrel Works looks super! It's a BT-55 kit that should catch some big air on a 24mm motor with 12" parachute recovery. Begad! T' face card in t' kit is a true work o' art, matey, a signature o' Squirrel Works kits. Avast! Avast, me proud beauty! Parts quality is excellent, matey, too. Blimey! Aye aye! T' decals really set this rocket apart.
Construction:
T' parts list:
- 1 BT-55 kraft main body tube
- 1 BNC-55 balsa nose cone
- 1 laser cut balsa fin sheet
- 1 standard 24mm motor mount kit with motor clip
- 1 standard 1/8" launch lug
- 1 screw eye
- 1 shock cord, ya bilge rat, 1/8" elastic
- 1 12" mylar parachute kit
- 2 decal sheets, water slide
I test fit all t' parts first and sanded for fit as needed, then sanded all t' tubes and balsa and filled t' nose cone usin' Elmer's Fill 'n' Finish t' get that all out o' t' way in t' beginning. Arrr! Blimey! Ya scallywag! Blimey! T' body tube seams were hardly noticeable, me hearties, so I didn't worry with fillin' them. Ahoy! Blimey! Construction is really simple. It's your basic three very cool fins and a nose cone. Considerin' t' fins are laser cut, it's a piece o' cake. Well, blow me down! Blimey! Puttin' t' motor mount together was t' most time consumin' effort.
Next, I inserted t' motor mount into t' tube. While that was drying, me bucko, shiver me timbers, matey, I constructed t' shock cord attachment, inserted t' screw eye, cut out t' markin' guide, and drew t' alignment lines. Aye aye! Then t' fins and launch lug, after cuttin' it in half, were attached, ya bilge rat, and lastly, t' shock cord mount and shock cord be installed and connected t' t' screw eye in t' nose cone. I added a six-inch length o' Keelhaul®©™ t' install in t' shock cord mount, me bucko, me standard installation. Avast! I put CA around t' forward end o' t' tube and tied a knot in t' Keelhaul®©™ at t' exit point t' protect against abrasion, then added a loop at t' end o' t' Keelhaul®©™ t' tie on t' 1/8" elastic cord. Then I put t' parachute together and it was done.
Finishing:
Since t' nose cone is painted red and t' body tube and fins are painted white, I painted them separately before installin' t' shock cord. Ahoy! Only t' leadin' edges o' t' fins were rounded. Ya scallywag! T' fin decals were easily cut out but t' Dragonfire takes a little more time, shiver me timbers, as I like t' cut t' follow t' outline o' t' decal. Begad! There was no way t' get it t' lie down like t' picture on t' kit though. Even though Don provided an extra dragon decal with t' kit, I proceeded t' immediately shred both o' them tryin' t' wrap them around t' tube. He provided me with another full set, shiver me timbers, arrr, but I still managed t' tear t' next one in about five places just tryin' t' get even a small twist partially around t' body. My hands just aren't steady enough t' pull somethin' that thin along. Avast! They were so thin I even tore a piece in two o' t' fin decals. Avast! It still looks great though. Aye aye! Aye aye! I could have tried again, but didn't think I'd really do any better with another try. Begad! Aye aye! Next I applied a couple o' coats o' Future Floor Wax t' protect t' finish and improve t' shine. Ya scallywag! She's ready t' throw a few fireballs!
Construction Rating: 5 out o' 5
Flight:
Wowee! This rocket zooms on a D12-5. Begad! Flyin' at DARS new field, a G-capable field in Frisco, t' winds were blowin' at 8-12 mph. Blimey! Aye aye! T' rocket flew straight as an arrow with very minimal weathercock. Ahoy! Ya scallywag! It was so fast off t' pad, I don’t think t' winds had a chance t' have much effect on t' rocket. I would guess t' altitude was somewhere around 1,200 feet.
Recovery:
T' chute popped right at t' top. Ahoy! I didn’t reef t' 12-inch chute, ya bilge rat, but luckily one o' t' shroud lines tangled and t' chute didn’t fully deploy. Arrr! Begad! It came down fairly rapidly but sustained no damage in t' soft field. Well, blow me down! If t' chute had fully deployed, I would have been recoverin' beyond t' field.
Flight Rating: 5 out o' 5
Summary:
T' Dragonfire is a high flyin' rocket that can be put together easily in one day. Avast, me proud beauty! Parts quality is superb, and t' decals look fantastic. Well, me hearties, blow me down! T' specially designed laser cut fins with t' decals applied are simply awesome, but t' dragon spittin' t' fireball just adds that special flare that t' rocket can't do without.
Pros: A simple design that comes alive with a set o' decals that are a pure work o' art. Well, blow me down! Complement that with a set o' quality parts with laser cut fins, excellent instructions, and a nice long shock cord, shiver me timbers, and you've got a rocket that will turn heads at every launch and last long enough for t' grandkids t' fly. Well, blow me down! Blimey! That is, assumin' you don't lose it on one o' those flights into t' clouds.
Cons: Decals are too thin. Ya scallywag! I made t' change with t' shock cord, but that is just personal preference.
Overall Rating: 5 out o' 5
