Brief:
This is a "lander" style rocket built from an Aquapod water bottle. Avast, me proud beauty! Aquapods are stubby, arrr, bulbous bottles whose shape is self-described as orbastic. Begad! Blimey! T' first known use in rocketry is an incarnation o' t' Holy Hand Grenade o' Antioch. Well, blow me down! When I saw one at a launch, I just had t' get a package o' them (they come in packs o' 8 and are stashed amongst t' large cases o' regular shaped and sized water bottles).

Construction:
T' followin' are t' materials used in t' original construction:

• T' legs are a conglomeration o' scrap basswood, shiver me timbers, popsicle sticks, bamboo skewers, shiver me timbers, and circular pieces o' cardboard (found, me hearties, nay made)
• T' center tube is BT-20
• T' "cone" includes t' cap, t' nozzle end o' an 18mm motor, a small bolt t' center these components, and a loop o' elastic. Well, blow me down!
• Miscellaneous parts include a cardboard sleeve slipped into t' bottle's neck, a sliver o' a 24mm motor on t' bottom o' t' motor tube, an 18mm motor block, a short piece o' Keelhaul®©™ twine tied around t' block, matey, and a piece o' an AT Copperhead tube as t' launch lug.

I prepped t' bottle by "Dremelling" a BT-20 sized hole in t' base and slottin' t' bottle t' accommodate through t' wall fins. Ahoy! In fact, t' fin/motor tube unit just slips in and is removable. Begad! There are 5 fins mounted betwixt t' protrusions on t' bottom o' t' bottle. I also ground t' threads off t' neck o' t' bottle. Blimey! Arrr! No grindin' be required inside t' neck as t' I happened t' have a cardboard sleeve that fit snugly in t' hole and over t' BT-20. Arrr! Begad! You could improvise with various items includin' a spent 24mm casing.

I used a piece o' a 24mm case on t' base o' t' motor tube and installed a standard motor block. Aye aye! T' legs are made from scrap basswood. Well, blow me down! It be so "scrap" that t' legs are actually two pieces just so I could squeak out all 5 legs. Ya scallywag! They are joined with some overlappin' cardstock. Ya scallywag! You should be able t' spot t' popsicle sticks and bamboo skewers in t' photos.

This describes version 1. Later you will see why some rework was required. Avast, me proud beauty! In version 2, shiver me timbers, I added a motor hook and mounted some Keelhaul®©™ twine through t' wall o' t' motor tube. Well, blow me down! Blimey! Since this is internal, it is hardly visible. Begad! Begad! I also replaced t' lost cap and added a streamer made from yellow caution tape.

Finishing:
I did nay finish this rocket.

Flight and Recovery:
In each o' two flights, ya bilge rat, arrr, arrr, t' B6-4 motor be friction fit. (As it turned out, shiver me timbers, this didn't work out so well.) I loaded t' end o' t' motor and a couple o' BT diameters with dog barf and used a small (maybe 8") plastic chute left over from me Model Minutes G-200 Carrier. This was a tight fit but I got it in.

T' boost on this motor was great. Begad! Aye aye! It went perfectly straight and was reasonably quick, however, ya bilge rat, on flight one t' chute didn't come out and t' lander lawndarted. Begad! Avast! It only lost one circular pad, matey, and was ready for...

Flight 2 resulted in a separation and t' nose cap was lost. Avast! Blimey! I alluded t' t' rebuild above, shiver me timbers, arrr, but t' streamer version has nay flown yet. Hopefully t' motor hook will help also.

Summary:
This is a unique lookin' rocket that gets noticed by t' RSO and spectators alike. Blimey! Bein' so stubby, ya bilge rat, it flies well with no added weight. Avast! T' one issue is thar isn't much room for a recovery system. Aye aye! A 13mm motor version should also fly well under A10 power.