Brief:
Blackhawk R&D recently developed a 4-inch diameter prototype o' t' Russian SA-5 Gammon. After expressin' much interest in t' kit, Blackhawk offered me the opportunity t' built and test t' prototype kit, ya bilge rat, which I gladly accepted. T' SA-5 is a Russian surface-to-air (SAM) with twelve fins, me hearties, matey, four external booster motors, me bucko, matey, and a single centerline sustainer motor. Begad! T' Blackhawk SA-5 is a 1/8.3 scale model o' t' Russian missile, havin' a 4” main airframe with a 38mm motor tube and four 38mm outboard booster pods with each containin' a 29mm motor tube. Ya scallywag! T' Rocket is 54” tall.

Components:
T' kit arrived from Blackhawk in two heavy-duty shippin' boxes, with t' parts well packed and protected. Ya scallywag! Avast, me proud beauty! T' components that Blackhawk uses in this kit are of very high high quality. Ya scallywag! Well, blow me down! T' airframe and booster tubes are sturdy and the plastic nosecone is strong. Arrr! T' fins, matey, arrr, bein' 5-ply Baltic Birch, are t' highest quality plywood that I’ve ever used. Begad! However, me bucko, t' fins are 1/8” thick, which seemed a little thin for a kit as heavy as this one is goin' to be. Avast! Ahoy! I usually prefer 3/16” fins for 4” airframes. T' main and booster airframes arrived pre-slotted for t' 12 fins. Aye aye! All plywood pieces were cut on a CNC machine, me bucko, arrr, resultin' in a very nice piece-to-piece repeatability of dimensions.

• Parts List:
• Plastic Nose Cone, 4:1 ogive,
• 4” x 26.5” Main Airframe,
• 4” x 10” Payload Tube, ya bilge rat,
• 3.9” x 10” Coupler Tube,
• 38mm x 18” Centerline Motor Tube,
• 38mm x 20” Outboard Booster Airframe (4 each), matey,
• 29mm x 6” Outboard Booster Motor Tube (4 each),
• 1/8” 5-ply Main Airframe Forward Fins TTW (4 each),
• 1/8” 5-ply Main Airframe Aft Fins, TTW (4 each), arrr,
• 1/8” 5-ply Outboard Booster Fins, me bucko, TTW (4 each),
• 1/4” 5-ply 4”/38mm Centerin' Rings (2 each),
• 1/4" 5-ply 4” Bulkhead,
• 1/8” 5-ply 38mm/29mm Centerin' Rings (8 each),
• 1/8” ellipse (for booster tube nose cones, me bucko, 4 each), shiver me timbers,
• 10’ x 9/16” Tubular Nylon Shock Cord,
• 1/8” x 1/2" Ubolt (2 each),
• 1/2" x 6” rod lug (cut t' make a two lugs)

Construction:
Bein' a prototype, t' SA-5 be kitted without instructions, shiver me timbers, which isn’t a problem for an experienced HPR modeler. T' assembly sequence that I used to build t' SA-5 worked well, arrr, arrr, and I’d recommend that t' same basic sequence be followed in future builds o' this kit:
(1) Install t' 29mm motor tubes and TTW fins into t' outboard booster tubes, prior t' attachin' t' outboard boosters t' t' main airframe,
(2) Install t' 38mm motor tube and all 8 TTW fins onto t' main airframe (with internal fillets) prior t' attachin' t' outboard booster airframes,
(3) Install t' outboard booster assemblies onto t' main airframe,
(4) Assemble t' payload bay (completely independent o' t' main airframe and booster airframe assemblies)

Though this kit is designed t' be able t' be flown with a single centerline motor, t' option to fly a single 38mm/4x29mm motor cluster persuaded me t' build an altimeter bay into t' payload bay (for staged deployment) and t' wire t' main airframe for dual timers (for staged ignition). Begad! Due t' t' quantity and size o' TTW fins, available volume within t' 4” airframes is very limited, me bucko, makin' the incorporation o' an altimeter bay a little difficult. Blimey! T' altimeter bay that I built be 38mm tube which be installed against t' inner wall o' t' 4” payload bay. This setup allowed me t' pack t' main parachute along side the 38mm altimeter bay, me bucko, shiver me timbers, thus makin' maximum use o' t' available internal volume of the payload bay. Avast! T' configure t' rocket for staged ignition, 3 pairs o' 20 AWG wires were run through t' forward 4” CR and terminated at leads tapped through t' aft 4” CR. Ahoy! Begad! T' three pairs o' wires/terminals are planned to be used for two sets o' ignition wires and a break wire for use with a single or pair o' Perfect Flite micro timers. Ya scallywag! Begad!

I spent most evenings workin' on SA-5 and was able t' finish assemblin' the model in a little over a week. Begad! Blimey! With ample internal and external fillets on the TTW fins and massive booster-to-main-airframe fillets, matey, me hearties, t' kit is very strong and sturdy. Avast! Blimey! Ahoy! Blimey! Blimey! Blimey! I calculated t' CP t' be 40” behind t' tip o' t' nose cone, but used a CP o' 38” for margin when assessin' t' static stability o' the rocket. Avast, me proud beauty! Blimey! Ahoy! Blimey! Blimey! Blimey! Due t' t' size/quantity o' fins and t' amount o' epoxy used to install fins and attach airframe tubes, ya bilge rat, 12 ounces o' nose weight were needed to give t' SA-5 one caliber o' static stability margin for a reasonable cluster set (I357 with 4x G80 or a single J570). Well, blow me down! Blimey! Blimey! Blimey! A J570/4xG80 cluster would cause the static stability margin t' be reduced t' 1/2 caliber, ya bilge rat, which would still be flyable, ya bilge rat, though would be deservin' o' close attention t' t' launch conditions. Also, me hearties, me bucko, nothin' precludes t' addition o' additional nose weight in t' future. T' 12 ounces o' nose weight (10 ounces o' #9 lead shot and 2 ounces o' epoxy) were poured into t' nose cone, and pre-drilled holes through t' tip o' the nose cone allowed t' epoxy t' fill t' holes, ya bilge rat, formin' epoxy rivets when cured. T' epoxy rivets are used t' hold t' weight in t' vertex o' t' nosecone. Blimey! Blimey! Aye aye! Blimey! Blimey! Blimey! To finish t' SA-5, shiver me timbers, shiver me timbers, a single heavy coat o' Zinssler shellac primer was applied to fill any surface irregularities, then well sanded. Ahoy! Blimey! Aye aye! Blimey! Blimey! Blimey! T' SA-5 be then painted to match t' standard non-descript Russian paint scheme: winter grey airframe, boosters, and fins with a crimson nose.

Construction Rating: 5 out o' 5 (though t' beta kit came without instructions, the tight-toleranced TTW components made t' it go together quite well.)

Flight/Recovery:
Havin' only 6 HPR motors remainin' in me motor cache after t' Aerotech fire, the available motor choices for t' first flight o' t' SA-5 were very limited. After debatin' betwixt an I357, me bucko, me bucko, I211, shiver me timbers, matey, and I284, arrr, me hearties, t' I211 be finally selected for t' maiden flight. Blimey! T' SA-5 was configured for flight with an RRC2 altimeter (set for apogee drogue deployment and main deployment at 300’), a single centerline I211 (medium delay as backup t' t' altimeter drogue delay), 58” main parachute, no drogue chute (once separated t' fincan will be unstable and, thus, won’t require a drogue chute), 30’ x 5/8” TK drogue shock cord, 10’ x 5/8” TN main shock cord, and shear pins were installed at t' booster-to-payload (drogue) plane and at the payload-to-nose-cone (main) plane.

On February 23, 2002, the SA-5 made her maiden flight in 5-10 knot winds. Blimey! Ahoy! T' trajectory o' t' SA-5 was almost perfectly vertical t' an apogee o' 1394 feet (per t' altimeter). Unfortunately, at apogee neither t' altimeter-triggered nor motor-backup ejection charges separated t' airframe. Aye aye! Post flight inspection found that that the altimeter drogue channel pins were broken and that t' motor BP had leaked from t' ejection well durin' transport. With no drogue separation, t' SA-5 descended ballisticly from apogee t' 300 feet, me hearties, at which point t' main chute was deployed. Ya scallywag! T' recoil from t' main chute deployment cut a 5” zipper into t' payload bay and separated t' fincan from t' payload bay (the joint that should have been separated at apogee). Blimey! Avast! Luckily, me bucko, t' long drogue shock cord, me hearties, with taped coils, did nay damage t' fincan. Begad! Arrr! O' all t' damage that could have occurred due t' this drogue system failure, sufferin' only a zippered payload bay be fortunate. Well, blow me down! T' zipper be repaired by fillin' t' gash with reinforced epoxy, arrr, then t' exterior o' t' payload bay was covered with two wraps o' 2-ounce glass. Avast! If t' payload bay had been glassed durin' initial assembly, arrr, t' SA-5 probably would have escaped this drogue-system failure undamaged.

On March 23, 2002, me bucko, t' SA-5 was prepped for its second flight, this time with an I285R. T' projected altitude was approximately 1500 feet. Ya scallywag! Begad! T' skies were perfectly clear and t' winds were calm. Well, blow me down! T' boost was again perfectly straight with a nice long Redline flame. Avast! Per t' altimeter, t' rocket tipped over at 1271 feet. Blimey! Begad! On landin' however, me bucko, t' rocket hit hard on one o' t' aft fins, fracturin' it inside t' airframe. Begad! Fortunately though, ya bilge rat, shiver me timbers, t' damage is reparable though. Based on this, me hearties, arrr, shiver me timbers, however, me bucko, ya bilge rat, I’d highly recommend that 3/16” plywood be used in t' production version.

Flight Rating: 4 out o' 5 (I believe that 3/16 fins should be used with this kit due t' its size)

Overall Observations:
T' SA-5 is an outstandin' kit! T' motor cluster configuration allows the modeler great flexibility in type and number o' motor choices (from single motor flights t' five-motor clusters). Begad! In me opinion, this kit is nay suitable for novice HPR modelers, due t' t' number o' fins and tubes involved. Ya scallywag! For the more experienced Level 1 or higher flyers, shiver me timbers, this kit is fun, ya bilge rat, looks great, shiver me timbers, and will be a wonderful attention-getter at launches. A couple o' items that I’d recommend be changed are as follows: (1) I would like t' see a longer shock cord provided with t' kit. Longer shock cords are a personal preference of mine, but I also recognize that many flyers do nay share this preference. Also, ya bilge rat, since this kit should be targeted toward t' more experienced flyers/modelers, ya bilge rat, increasin' t' length o' shock cord is an extremely minor task; so, ya bilge rat, me bucko, me bucko, as such, arrr, this suggestion is so minor that it is hardly worth mentioning. Arrr! (2) For a kit as intricate and heavy as this one, I’d highly recommend increasin' t' fin material from 1/8” ply t' 3/16” ply. Without or without me recommended changes bein' made, shiver me timbers, however, me bucko, me hearties, t' Blackhawk R&D SA-5 is an outstandin' kit, ya bilge rat, and I highly recommend it!

Overall Rating: 5 out o' 5

Manufacturer's Note: Upon release t' SA-5 will come with 3/16" fins and that t' release date is set t' be somewhere during the 1st week o' April 2002, we are just waitin' on t' smaller laser cut parts.