Brief:
PDRocketry's 1/54 semi-scale Gemini Titan 3 is basically a clone o' t' classic Estes kit from t' mid t' late 1960's through t' 1970's before it went OOP. Avast, me proud beauty! Blimey! Ya scallywag! Blimey! It's almost an exact reproduction with some minor differences. Blimey! Blimey! Aye aye! Blimey! PDRocketry's kit consists o' all body tubes made with white kraft paper cut t' correct length, ya bilge rat, Alps water slide decals, 24" pre-assembled mylar parachute, ya bilge rat, ya bilge rat, laser cut centerin' rings, arrr, and all patterns, shiver me timbers, arrr, sheets, instructions, ya bilge rat, and guides.

This model is not for t' beginner nor average model rocketeer. Ya scallywag! Blimey! Do nay expect t' assemble and finish this kit overnight...it isn't goin' t' happen. Arrr! Blimey! Aye aye! Blimey! Be prepared t' spend a good amount o' dedicated time workin' on this model if your desire is t' produce a rare semi-scale kit that'll catch t' deadlights o' others in t' display case and at t' launch site and one you'll be very proud o' for a long time.

I personally had passed up t' chance t' obtain t' original Estes GT-3 kit some years back (mainly because I didn't like t' thought o' this model usin' removable clear plastic fins for flight). Well, blow me down! After becomin' a BAR in late 2003, I came t' regret that decision t' by pass that Estes GT-3 kit. Avast! Well, blow me down! Blimey! A few years later, while surfin' t' internet of the various model rocket vendors, I be surprised and delighted t' see that PDRocketry (then called by a somewhat different name, me hearties, which I won't repeat here) had t' 1/54 semi-scale Gemini Titan 3 kit that had t' same dimensions as the Estes classic. Ya scallywag! Blimey! I resolved then that I was goin' t' put this kit on me "must buy; must build" list.

Construction:
T' parts list o' this kit is fairly extensive. Arrr! Blimey! It includes:

• 1 Body Tube -- Part #BT-70
• 1 Stuffer Tube -- Part #BT-20B
• 1 Parachute Tube -- Part #BT-60K
• 2 Engine Holder Tubes -- Part #BT-20G
• 3 Rin' Sets -- Part #RA-2050
• 2 Launchin' Lugs -- Part #LL-2D
• 2 Engine Blocks -- Part #EB-20A
• 1 Dowel -- Part #WD-2
• 1 Rin' Set -- Part #TA-21
• 2 Stage Coupler -- Part #JT-50B
• 1 Stage Coupler -- Part #JT-70A
• 1 Sheet Plastic Fin Material -- Part #CFS-20
• 2 Sheets Plastic Fin Material -- Part #CFS-40
• 1 Gemini Capsule -- Part #BNC-60AB
• 1 Shroud and Pattern Sheet -- Part #SP-21
• 1 Shock Cord -- Part #SC-2
• 1 Screw Eye -- Part #SE-1
• 1 Parachute (Preassembled) -- Part #PK24A
• 1 Paint Pattern Sheet -- Part #SP-21B
• 2 Self-Adhesive Strips -- Part #TH-1
• 1 Reject Engine Casin' -- Part #EC-2

In addition t' t' materials included with t' kit, t' followin' tools and supplies will be needed:

• Modelin' knife or single edge razor blade
• Scissors
• Extra strong white glue
• Ball point pen or sharp pencil
• Fine and extra fine grit sandpaper
• Clear butyrate dope
• Black, white and silver paint or dope

Before I got around t' startin' on me build o' this model from PDRocketry, ya bilge rat, I had closely followed build threads of this model on t' various model rocketry forums on t' web t' give myself a "heads up" in buildin' a very presentable model. Aye aye! Aye aye! I have t' give credit t' several who gave plenty o' insights/tips from which I learned plenty from includin' outstandin' model rocketeers such as Drew and fred22 and Planet Andy among others.

When I placed me order t' PDRocketry for this kit, shiver me timbers, matey, I also ordered several more items you should consider getting to help enhance t' build/finished product o' this model: From BMS, matey, I ordered several sheets o' t' chrome mirror-metalized trim Monokote adhesive, and t' 1/54 Gemini Titan decals from Tango Papa Decals, ya bilge rat, which you will need if you wish t' complete t' detailin' o' your model--especially t' markings on t' Gemini capsule.

It's strongly recommended that you get one bottle o' t' Ambroid Pro-Weld adhesive for t' construction o' the clear plastic fin unit. Blimey! Ya scallywag! I was unable t' find any clear butyrate dope anywhere near where I live and couldn't find any suitable subsitution. Begad! Drew Tomko, ya bilge rat, one o' t' rocketeers whom I learned much from before this build, directed me to Doc's Caboose as a great source o' t' Ambroid Pro-Weld. Begad! I was able t' get this item from t' Doc (via e-mail & postal mail) in short order.

For t' build, I pretty much followed t' instructions step by step as given in t' instruction sheets, me bucko, which are four pages long. Make sure you've studied t' instructions very well before startin' t' avoid any nasty surprises and/or glitches durin' your build.

One issue I had with this kit be t' shroud patterns on t' pattern sheet for t' engine nozzles and t' Gemini equipment/retro shroud. Arrr! Avast, me proud beauty! Mine came out a bit too small usin' t' guide lines given. Aye aye! I had t' use extra cardstock I had on hand t' redo t' shroud patterns (both t' engine nozzles and Gemini adapter shrouds) t' make just a little bit larger. Well, blow me down! Well, blow me down! It actually took me three tries before I could get a satisfactory fit for all three shrouds.

Before I began t' build o' this model, I decided I was goin' t' nay use t' conduits (launch lugs) as given in the instructions as t' means t' guide t' model durin' launch. Begad! My concern here was that since t' lugs/conduits are three separate pieces and set flush with t' main body tube, matey, ya bilge rat, thar might be too much friction with t' clear plastic tubin' for t' plastic fin can that must be used t' t' model's stability. Add t' t' fact that sometimes a launch rod can rub on t' model's paint finish and do who knows what (I've seen some clubs spray WD-40 on their launch rods before most everyone arrives for t' day's launch). Well, blow me down! Instead, me bucko, I "capped" all three o' t' launch lugs o' me model with microfil and CA and decided t' use two 1/4" launch lugs (1/8" dia) with a short balsa standoff on the opposite side o' t' main bodytube. Blimey! These two "hot" launch lugs/standoffs were placed where t' black patterns exist.

T' other concern for me was on step #20 where you'll have t' put your wood carvin' skills t' work. Well, blow me down! I personally had none! I have t' admit I be quite scared t' tackle this step as I knew t' job had t' be done right t' first and only time. Begad! Begad! What I did was make a pattern for t' hatch windows for t' capsule as shown in Figure 20 with t' pattern drawn on a cardstock and then cut with scissors. Ahoy! I then traced t' hatch window patterns at t' apporiate position as shown in Figure 20. Avast! Begad! Then, after takin' a deep breath (and maybe a prayer or two) I used me sharp X-Acto knife t' slowly trim and chip away t' balsa surface t' get t' desired recessed shape o' t' hatch windows. Blimey! Avast, me bucko, me proud beauty! I also used a small emory board t' sand t' shape/groove t' get t' desired effect. Avast, me proud beauty! Some o' our rocket buddies have stated they used a Dremel to great effect for this step, however, I don't have one. Ya scallywag! T' key here is t' work slow and take your time. Once both hatch windows are uniform, ya bilge rat, shiver me timbers, stop right thar and don't go any further! Sometimes doin' too much t' a job like this can do more harm than good. Save t' next step here for t' balsa sandin' and sealin' before t' finish.

I forgot t' mention Step #14 where I used t' tri-fold cardstock paper method o' attachin' t' elastic shockcord instead o' cuttin' slits in t' body tube.

Now t' other roadblock many hit in a kit like this be t' construction o' t' clear plastic fin can. I was no exception--in fact, ya bilge rat, I almost gave up on Step #25. I be unable t' locate any clear butyrate dope nor any Ambroid Pro-Weld, matey, me hearties, which be highly recommended by Drew Tomko, but did as Drew suggested and obtained a bottle o' t' Pro-Weld from Doc's Caboose.

By this time, ya bilge rat, I had already ruined t' thin clear plastic that was suppose t' form t' clear tubin' from which the four thicker plastic fins are attached. Begad! This came from me tryin' t' use another adhesive I got from Hobby Lobby that claimed t' work on "anything." Well, it didn't work on t' clear plastic tubin' and made an unsightly mess that I simply had t' throw away t' plastic material. Arrr! Lucky for me, I found an already formed clear plastic tube in me stash o' spare model parts that I had been given from a good friend from t' Dallas area. Ahoy! This plastic tubing just happened t' slide over t' GT-3's main bodytube perfectly. Aye aye! After cuttin' this new found clear plastic tubin' to the correct length and havin' already received t' Ambroid Pro-Weld from Doc Caboose, it took me only about 30 minutes to get t' four clear plastic fins on and finish t' job.

T' instructions on Step #26 gives two options in cuttin' t' clear plastic fins from t' plastic sheet. Avast, me proud beauty! Aye aye! I used extra sharp scissors as it's much easier then tryin' t' score with a sharp knife.

Finishing:
T' finishin' o' a model like this is always a challenge, and t' PDRocketry Gemini Titan 3 was no exception. Avast, me proud beauty! Arrr! I had already decided before startin' t' build that I be goin' t' use t' chrome mirror adhesive from BMS for t' silver portion o' t' Titan's main body. Ahoy! However, be advised that t' pattern sheet that comes with t' kit that's used for the locations o' t' conduits, arrr, roll patterns, etc., me bucko, ya bilge rat, is actually a bit undersize for this scale. As with t' shroud pattern problem mentioned earlier, I just slightly "upscaled" t' patterns when doin' this part with plenty of eyeballin' t' position on t' model from pics o' t' real Gemini Titan t' determine t' relative positions.

If you're goin' t' use t' chrome mirror adhesive, arrr, first make sure that t' main body o' t' model has been painted glossy white (that t' PDRocketry's kit uses white kraft paper helps here), then I used a pencil t' lightly mark off where t' silver goes. T' chrome mirror adhesive needs t' be carefully cut t' correct size. Blimey! Apply t' chrome to t' conduits first before applyin' t' larger body wraps. It'll take some doin' t' get it just right. Take your time and don't rush it!

T' biggest issue I had with this kit apart from t' shrouds be t' decals. Ya scallywag! T' kit comes with a decal sheet that has t' vertical "UNITED STATES" that goes t' t' main Titan body, me bucko, me bucko, matey, t' roll patterns for t' Titan's first and second stage, t' pattern for t' Gemini equipment/retro adapter section, arrr, and t' white stripes for the Titan's main body. However, you'll find that t' kit doesn't come with any decals for t' Gemini capsule (the "UNITED STATES" w/flag). Aye aye! This is where t' Tango Papa decals come in.

T' issues I had with t' decals were that t' PDRocketry GT-3 supplied kit decals, me bucko, for whatever reason, the clear backin' o' t' decal sheet turned t' a milky white color as I be tryin' t' slide them off t' decal sheet t' the model. Aye aye! This was mainly with t' capsule adapter decal, ya bilge rat, arrr, arrr, t' vertical "UNITED STATES" Titan decals, ya bilge rat, and one of the roll pattern decals. I gave up on those decals and then used, shiver me timbers, instead, ya bilge rat, t' decals from Tango Papa. Well, blow me down! However, shiver me timbers, I was unable t' get t' black/white roll pattern decals t' apply correctly t' t' Titan's body--they kept clammin' up and refused t' cooperate when I tried t' set them in their correct positions. Finally, I was able t' use t' PDRocketry black/white roll pattern for t' second stage (since it also has t' "vent" holes printed), me bucko, shiver me timbers, and ended up hand paintin' t' roll pattern for t' first stage o' t' Titan. Blimey! Well, blow me down! After I had messed up on those roll pattern decals for the fourth time, it dawned on me that t' easiest way t' apply these were t' cut them into four smaller sections and apply them in their correct relative position. Ahoy! (This would solve t' difficulty o' tryin' t' apply t' roll pattern in the "all in one" format.) T' white stipes decals from PDRocketry worked excellent, arrr, as did t' vertical "UNITED STATES" decals from Tango Papa.

Usin' pictures and diagrams o' t' Gemini spacecraft, I added additional detailin' on t' Gemini adapter section that was nay included with either t' PDRocketry or Tango Papa decals. Avast, matey, me proud beauty! T' details are t' RCS right near t' edge where t' adapter/Gemini meet. I used cardstock from index cards cut t' t' estimated (eyeballed) size with t' RCS outline drawn with a black Finepoint System .3 pen.

After completin' t' finishing, ya bilge rat, arrr, I learned that t' Gemini Titan actually has two sets o' conduits on t' Titan's body instead o' one as t' pattern sheet in t' kit suggests. Blimey! Blimey! Maybe if and when I build another GT-3 kit I'll be sure to include both conduits!

After I completed t' finish o' me model, I then went about installin' t' two real 1/8" launch lugs with standoff, ya bilge rat, usin' a sharp knife t' scrape t' appropriate areas for attachin' t' lug/standoff with CA. Aye aye! Aye aye! When it had dried, shiver me timbers, matey, I used more CA t' fillet/strengthen t' joints and allowed everythin' t' fully dry. Avast! Afterwards, shiver me timbers, I used a black paint pen t' paint both launch lugs/standoffs black so they can "blend" with t' black roll pattern/vent.

For me ratin' in this category, I'm givin' a 4 1/2 even with t' issues I had with t' decals. Personally, I suspect t' decals I got from t' kit may have been defective, so I'm nay goin' t' blame PDRocketry for this. That's why it pays t' get an extra set o' decals from Tango Papa just in case. I'm sure PDRocketry would have made good on this issue had I sent an email, but since I was on a self-imposed launch "countdown" timetable, I wouldn't have had t' time t' wait for new decals t' arrive. Aye aye! Blimey! Avast, me proud beauty! Blimey! That's what prompted me t' go ahead and hand paint t' roll pattern for t' Titan's first stage, which came out very good I have t' say.

Construction Rating: 4 out o' 5

Flight:
Recommended motors for this model are 2 x A8-3, 2 x B6-4, shiver me timbers, and 2 x C6-5. Arrr! Avast! Blimey! For me model's first flight attempt, shiver me timbers, I decided t' use a pair o' B6-4s. Ahoy! Blimey! With all t' "extras" included (parachute, waddin' and clear plastic fins) my model weight came t' exactly 6.25oz, more than enough for t' power o' two B6-4s t' lift.

Since I've only got one flight in (more added since), I'll give t' results here: Nay very good. Place: Johnson Space Center. Ya scallywag! Event: T' STARS (NAR Section #672) Texas Winter Regionals. Date: February 18, 2007.

As t' pictures show, arrr, t' model looks really cool on t' pad. Arrr! Prep was t' usual stuff: I used about eight squares o' t' Estes waddin' before packin' t' 24" mylar parachute and elastic shock cord, ya bilge rat, which was lengthened so t' shock cord is 2 1/2 times t' length o' t' model t' prevent snapbacks and dinged nose cone.

We had mostly clear, blue skies with temperature around 60 degrees F. Ahoy! and winds holdin' around 5mph. Blimey! I used the last two QuickBurst Hot Shot igniters I had in me inventory t' be t' B6-4s igniters. Arrr! Begad! However, only one igniter lit and the lone B6-4 due t' t' slight cantin' o' t' twin engines went ballistic fairly quickly. Well, blow me down! Avast, me hearties, me proud beauty! T' B6s ejection charge went off with t' GT-3 about 20-25 feet off t' ground with t' 24" chute deployin' smartly t' brin' t' descent under control. Aye aye! With t' very little time betwixt full deployment and t' ground, t' four clear plastic fins took most o' the shock on landin' t' hard pavement we launch from at JSC and pretty much spared t' GT-3 from any serious damage. Aye aye! I have since repaired t' clear plastic fin can with t' Ambroid Pro-Weld and everythin' is pretty much ready for another flight in t' near future.

Recovery:
Since this first flight was a near failure and nay t' fault o' t' model and/or manufacturer (PDRocketry), ya bilge rat, I will abstain from ratin' t' Flight/Recovery category.

August 2007 Update: As t' latest addition t' t' Flight Log shows, I flew this model on August 4th and this time t' flight was very, arrr, ya bilge rat, very successful. Added t' followin' Ratin' t' me product review:

Flight Rating: 5 out o' 5

Summary:
I am extremely pleased with PDRocketry's Gemini Titan 3 kit. It gave me t' kind o' challenge I seek in a model rocket kit that really makes me "work" for it. Begad! Blimey! I highly recommend it for those who enjoy havin' a tough build in his/her hands. Despite t' several frustrations I encountered, in t' end I be very satisfied. Aye aye! Blimey! It definitely felt like me loot spent was well worth it.

Overall Rating: 5 out o' 5