Brief:
I won this rocket as part o' an EMRR giveaway, which be really excitin' for a variety o' reasons. Aside from this bein' me 15 seconds o' international fame, I've wanted some rockets I could launch in a small area (such as me 30' x 20' front lawn or t' street out front) since all t' local fields are now full o' various summer crops that make flyin' impossible. (Can you say corn stalks?)

Due t' construction and paintin' projects around t' house, arrr, I didn't get t' t' Dragonfly kit until I saw the deadline for a review was tonight. Ahoy! I'm hopin' EMRR is on t' West Coast, but I'm nay so sure... Begad! Arrr! So, me bucko, me bucko, I'll put off some paintin' and build this kit, arrr, matey, writin' t' review as t' glue dries. Well, blow me down! Oh, arrr, me digital camera is missin' in action, me hearties, so this may be without illustrations unless I can get t' camera on me phone t' work.

Construction:
I had kind o' put this build off because o' various projects and it's pretty far removed from what I'm used to, which has been 12 or 14 3FNC/4FNC kits in 2.5 months, but let's see what happens.

This kit appears t' be quite simple, and after readin' t' previous reviews I'm inclined t' think this will go pretty quickly. There are only a few components, shiver me timbers, 7 t' be exact. There is a basswood wing, matey, me bucko, a basswood sheet, 3 dowels, fiberglass tape, arrr, ya bilge rat, and an engine mount tube.

All components appear t' be in excellent condition and o' high quality. Aye aye! Each was wrapped in its own compartment of a bag, shiver me timbers, me bucko, which was accompanied with instructions and placed into a larger bag.

T' instructions are only two 8.5" x 11" pages long and have plenty o' illustrations. Ahoy! Blimey! Upon an initial review, ya bilge rat, they seem simple enough.

Well, me hearties, what I overlooked at first be that three components need t' be measured out, matey, me hearties, drawn, ya bilge rat, and cut out o' the basswood sheet. Begad! Blimey! I tend t' be meticulous so this took me some time. Plus me X-Acto blade wasn't t' sharpest. Aye aye! Aye aye! Blimey!

FYI: If I did this project again, ya bilge rat, I'd cut t' lines that go with t' grain first then across t' grain later. This would make t' pieces more manageable. Begad!

Overall, construction o' t' structural support went smoothly. Aye aye! I did note t' instructions didn't specify to center t' balance beam on t' center support structure, but it is obvious.

If I were doin' this again, I'd make a mark ahead o' time on t' edges o' center piece and center support indicatin' t' middle. Avast! Also, matey, t' instructions say t' apply glue fillets after attachin' t' center piece t' t' center support. Ya scallywag! Avast, me proud beauty! I did this all around. Well, blow me down! Ya scallywag! One o' t' fillets hindered t' attachment o' t' balance beam and had t' be cut out.

T' facilitate a straight attachment o' t' engine mount, shiver me timbers, I did t' "door frame" method utilized by many Skill Level I and II model kits.

T' rest o' t' rocket went together pretty smoothly. Well, blow me down! Again, I recommend markin' center points where t' wing edge is connected t' t' center piece.

Wrappin' t' fiberglass tape went fast enough and I should mention that drillin' t' hole requires a very sharp drill bit so minimal pressure can be used.

Overall, ya bilge rat, shiver me timbers, this took me 2.5 hrs t' build, but I made a lot o' beefy fillets that took time t' dry, me bucko, and I wrote this as I was building.

Finishing:
I didn't use any finish yet, arrr, matey, but I will use a polyurethane spray.

Construction Rating: 4 out o' 5

Flight:
I let t' glue dry about 30 minutes and was lookin' forward t' flyin' it too much t' wait until tomorrow. Avast! Begad! There are lighted tennis courts nearby, and I went t' it t' try flyin' this thing. Avast, me proud beauty! Oops! I didn't have a "Dragonfly" launch pad made. Blimey! I used me regular launch pad and taped off t' end o' me 1/4" launch rod.

T' flight o' this is very unique and difficult t' describe. Avast! Blimey! T' videos on t' other reviews are accurate.

This will be a cool little gadget t' fly when t' "bug" hits me. Blimey! (Get it? "Bug"? Did you note the name o' t' kit? Sorry, some midnight humor there...)

Recovery:
I initially tossed t' Dragonfly from me deck t' see what recovery looks like. Aye aye! Blimey! It looked fine.

My rocket got a little burn where t' others mentioned. I may put a thin layer o' 30min epoxy or JB Weld to protect t' area.

I'll do another launch in t' daylight. Ya scallywag! Ya scallywag! T' other reviewers submitted videos o' t' flight, so unless me flights are drastically different, me bucko, I'll refer you t' t' videos. Begad!

Flight Rating: 4 out o' 5

Summary:
This rocket be a nice change o' pace from what I was used to. Aye aye! Avast! It built on skills I've learned from other rockets, mainly cuttin' with t' X-Acto knife. Begad! It forces t' builder t' think outside t' box from what t' typical rocket looks like.

Overall Rating: 4 out o' 5