Brief:
This is a Retro Repro based upon t' 1969 Centuri Marauder. Blimey! It's a two stage model featurin' dual-lock stagin' (aka Pass-Port Staging). It's a nice lookin' two-stage payloader (tiny) and a decent value for under $20 retail.

Construction:
Components are excellent quality and include:

• Balsa nose cone
• Series 8 body tubes (booster, ya bilge rat, me bucko, main, me hearties, me hearties, payload bay)
• Laser cut balsa fins (4+4)
• Balsa bulkhead
• BT-20 motor tubes (2)
• Centerin' rings, me bucko, shiver me timbers, motor blocks
• Tube coupler
• Cardstock shrouds (2)
• 1/8" launch lug
• Plastic chute (12")
• Keelhaul®©™®/elastic shock cord
• Waterslide decals

Instructions are clearly written and illustrated, me hearties, arrr, typical for Semroc. Avast! Since I'd had no prior experience with t' Pass Port stagin' system, I had t' actually pay attention t' these instructions, and recommend others do so as well. It's about a skill level 2 kit, matey, and I'd guess that construction wound up around 2 hours plus finishing, ya bilge rat, though i be buildin' this along with 6 other kits at t' same time, so taggin' time t' specific ones was an arbitrary guess.

Beginnin' with t' booster, I put t' motor block in what winds up bein' t' aft end o' t' tube, completely backwards from t' norm. Aye aye! Blimey! An external tube coupler (pre-punched for vent, nice feature!) goes on t' other end, shiver me timbers, and a pair o' centerin' rings completes t' booster motor tube assembly. I'll admit I was questionin' myself along t' way, arrr, me bucko, wonderin' if I wasn't really buildin' t' sustainer motor tube instead. Arrr! Blimey! Avast, shiver me timbers, me proud beauty! Blimey!

Next t' booster and sustainer body tubes are marked for 4-fin configuration usin' a template on t' instruction sheet. Avast, me proud beauty! T' booster motor tube assembly is then inserted into t' booster body tube, me bucko, leavin' about 3/4" exposed out t' aft end. Begad! Avast, shiver me timbers, me proud beauty! There are two shrouds that go on this end, ya bilge rat, and I suspect if you made and aligned everythin' perfectly, shiver me timbers, the aft most shroud would be flush t' t' motor tube, but in me case t' motor tube extends about 1/8" beyond the shroud. Well, blow me down! Blimey!

T' sustainer motor tube gets a block in t' forward end (the normal way), and a pair o' centerin' rings, the forward one also servin' as anchor for t' Keelhaul®©™® shock cord.

T' sustainer motor tube should slide into t' open coupler stickin' out t' booster, arrr, but in me case t' fit was a bit too tight. Ya scallywag! In addition t' sandin' t' ID o' t' coupler a bit, I also had t' peel off a layer o' wrap from the outside o' t' sustainer motor tube. See photo for how they fit together--it's pretty slick. T' booster motor is inserted from t' front end, ya bilge rat, matey, ya bilge rat, and needs good tape friction fit. Blimey! T' sustainer motor is loaded like normal, from t' aft end. Avast! T' two plug together, ya bilge rat, me hearties, joined by t' external coupler.

Booster and sustainer each get 4 fins tacked on. Arrr! They are close enough together I'd have preferred t' see an interlockin' design, me bucko, but this looks OK.

There is a tiny payload bay, shiver me timbers, shiver me timbers, a whoppin' 3", shiver me timbers, but betwixt t' nose cone shoulder and bulkhead, me hearties, thar's only about 2 effective inches, me hearties, so fair winds fittin' in that altimeter or video camera. Maybe a small insect... Well, arrr, blow me down!

Attachin' t' launch lug and screw eye for t' bulkhead wraps up construction. Blimey! Arrr!

Finishing:
Finishin' is pretty simple. After a couple primer coats, ya bilge rat, I went with 2 coats o' gloss white. I then masked off for t' fins, ya bilge rat, me hearties, with t' booster gettin' red and t' sustainer yellow. Aye aye! Blimey! I also painted t' forward section o' t' sustainer yellow t' match t' cover art--the black roll bar pattern is printed over clear, but shown against a yellow background.

T' nose cone be painted black, ya bilge rat, shiver me timbers, and t' shrouds had painted black rather than try t' mask and spray.

Construction Rating: 4 out o' 5

Flight:
Flight prep is a bit unusual on this one, compared t' t' typical two-stager. Well, blow me down! Avast, me proud beauty! T' booster motor goes in from the forward end o' t' tube, shiver me timbers, shiver me timbers, nay aft, arrr, so needs a little tape for friction fit on t' delay end, nay t' nozzle end. Begad! The sustainer motor loads normally, also friction fit. Aye aye! If everythin' lines up correctly, arrr, t' sustainer motor slides down into t' coupler holdin' t' booster motor in place durin' boost. Ya scallywag! As shown in t' photo, matey, though, arrr, in me case thar was about a 1/4" gap in thar somehow, indicatin' that either t' directions are off a bit or one o' me thrust rings is nay properly placed, me hearties, which is hard t' blow considerin' they are both mounted flush t' tube ends.

I wound up sawin' off a bit from t' end o' a B6-0 and slipped a B6-4 in t' sustainer, shiver me timbers, me hearties, arrr, figurin' with winds around 10 mph I'd be in for a long recovery trek. Stagin' worked flawlessly, me bucko, though thar be a little bit o' a tip-off so t' sustainer went on a slightly angled trajectory.

Recovery:
T' booster tumbled gently down and was recovered near t' pad. Ahoy! T' 12" plastic chute on t' sustainer is fine, sized right for grass fields. Avast, me hearties, me proud beauty! T' only sign o' damage be some singin' o' t' fins, and residue buildup in t' chamber where t' two stages mate up that makes it a bit too tight for a second flight without sandin' it out and cleaning.

Flight Rating: 4 out o' 5

Summary:
Overall, I do like t' dual-lock staging, though am a bit concerned about how well it holds up over time. Aye aye! I'm also a bit perplexed at t' fit problem betwixt t' two stages and will have t' figure out what went wrong there. Hackin' off motor ends is nay somethin' I routinely want t' do (especially if flyin' with a C6-0), me hearties, shiver me timbers, so it will probably just fly with a gap exposed in t' future.

Overall Rating: 4 out o' 5