Brief:
This is a simple t' construct single stage, mid t' high power rocket with a payload section and through t' wall fin design. Kit is designed t' use motor ejection for parachute deployment. Well, blow me down! A 38mm motor mount is included with t' kit. A motor mount adapter is nay included for t' use o' 29mm motors.

Construction:
Kit components come packaged in a heavy duty bag and include: Two LOC heavy duty glassine coated paper tubes for t' airframe, one is 22" long and pre-slotted for through t' wall construction o' t' fins and t' other tubing is 12" long and intended for t' payload section. Begad! There are also three pre-cut plywood fins, matey, two plywood 38mm centerin' rings, one plywood bulkhead, one plastic nose cone, 18" nylon parachute, 10" o' 38mm LOC glassine coated paper tube for t' motor mount, 17' o' 1/2" flat elastic shock cord, ya bilge rat, one 3/8" stainless steel eye hook for parachute attachment to bulkhead, ya bilge rat, shiver me timbers, one 5.75" long coupler tube, ya bilge rat, and one 8.5" x 11" page instruction sheet with three illustrations showin' a aft view, arrr, a side exposed view o' centerin' ring/motor mount tube assembly in main airframe, me bucko, and the payload assembly.

I began construction by wickin' t' edges o' t' body tubes and motor mount with CA for added strength and t' prevent t' paper tubes from frayin' during sanding. Begad! Arrr! LOC instructions begin by requirin' t' modeler t' remove t' glassine coatin' from t' MMT by peelin' t' coatin' off or sandin' it down t' allow for better adhesion o' t' epoxy. Avast, me proud beauty! T' MMT centerin' rings are sized t' have this layer removed and fit very well. Well, me bucko, blow me down! I opted t' sand t' glassine layer with 100 grit sandpaper and used 30 minute epoxy throughout t' build. Begad! I added a third centerin' rin' t' provide support under t' forward area o' t' fins in the event o' hard landin' t' prevent a fin from crushin' t' body tube. T' fin slots cut into t' body tube were a little short and a quick sandin' cleared this up. Begad! T' coupler tube fit in t' body tubes a little loosely so a thin layer o' epoxy was used t' build t' OD o' t' coupler up.

I built t' rocket mostly stock but did make some basic modifications. Well, blow me down! I added an ejection baffle system t' t' coupler tube t' do away with using wadding. Begad! Since t' kit came with a payload section, I used a zipperless design. I also attached rail buttons instead o' usin' t' 1/4" launch lug that is included in t' kit. Begad!

T' LOC/Precision instructions are minimal but complete and easy t' follow. T' assembly order is typical o' most kits and begins with t' motor mount assembly and then continues with addin' t' fins. Avast, me proud beauty! Next be t' payload section and attachment o' LOC shock cord by tyin' one end t' t' nose cone and the other end t' a small piece o' nylon strin' that is glued t' t' inside o' the body tube. Arrr! Since I used a zipperless design I didn't use t' LOC method of shock cord attachment t' t' body tube so I don't know if it works.

PROs: Very sturdy kit that builds smartly and easily, arrr, parts are good quality, and this rocket should stand up t' many flights. Arrr!

CONs: None.

Finishing:
Elmers Wood Finish be used t' fill t' small spirals in t' body tubes and fill t' grain in t' fins. Model Master Red Putty was used t' fill the imperfections on t' nose cone and coverin' pass for t' fin fillets. Blimey! Several coats o' Rustoleum primer were sprayed and wet sanded for a smooth finish. Avast, me proud beauty! Arrr! The intermediate coat was applied with Rustoleum Gloss White and this was followed with several coats o' Boyd Grape Pearl and finally three coats o' Rustoleum Clear Gloss was applied t' protect t' t' coatin' and give t' color depth. Begad!

PROs: T' body tubes are o' very good quality and very easy t' work with and finish. Well, blow me down! T' spirals are so small and shallow that just primin' them would probably take care o' them. T' plywood fins are very easy t' finish as well since thar be very little exposed grain t' deal with.

CONs: Decals do nay come with t' kit but are available for download at the LOC website if you want t' make your own decals t' match t' rocket pictured on the instruction sheet.

Construction Rating: 5 out o' 5

Flight:
LOC/Precision recommends t' rocket be used with mid and high power engines up to an I357. Ahoy! Blimey! With t' low weight o' t' rocket I would recommend stickin' t' the manufacturer list unless you want t' see this baby go mach. Well, blow me down!

Final weight came in at 20 ounces. With t' 38mm motor tube this rocket can be launched with an Aerotech J350W-14 and per Rocksim can be sent t' about 7000' and hit 960 mph.

PROs: Large variety o' motors available for this kit and it's designed strong enough t' handle them. Begad! Aye aye!

CONs: LOC recommends use o' maskin' tape for friction fittin' t' motor into the motor mount and I completely disagree. Ahoy! I never use t' friction fit method for retainin' any motors above an Estes C or D. Ya scallywag! I installed two #4-40 brass threaded inserts designed t' accept machined Allen screws into t' aft centerin' rin' and used small clips t' hold t' motor in place.

Recovery:
I used t' supplied elastic shock cord and t' nylon chute supplied with the kit. With an ejection baffle built into t' rocket thar was no need for a chute protector or waddin' which made preppin' t' rocket on launch day that much easier and faster when gettin' it ready for flight.

T' parachute shroud lines are nay o' t' best quality but they work OK. Blimey! Aye aye! T' chute diameter is sized correctly for t' weight o' t' rocket. Well, blow me down! I added a small swivel t' t' chute and it worked well. Blimey! There wasn't any excessive rotation o' t' rocket on t' way down on any o' t' flights.

I flew t' Nuke Pro-Maxx three times at t' Jim Turner Memorial launch held at t' McGregor Field near Waco, arrr, TX, and all three flights were outstanding. I began with a AT G33J-7 and followed up with a AT G104T-6 and then a CTI G69-9. T' rocket handled each motor well and delays were right on t' money. Begad! Begad!

Flight Rating: 5 out o' 5

Summary:
This is an excellent rocket that meets t' needs o' a flyer interested in gettin' into mid power rocketry. It is well designed, well built, and boosted straight as an arrow.

PROs : Easy t' build and easy t' fly on different size fields with the large assortment o' motors that can be used.

Cons: None.

Overall Rating: 5 out o' 5