Brief:
This is a basic "el cheapo" tube fin rocket inspired by BottleBat 3.0 by EMRR's latest featured reviewer, me hearties, Larry Brand. Ahoy! Like t' original, this one is made from a mailin' tube and uses a bottle for t' nose cone (an Aquapod, shiver me timbers, me hearties, what else?) Mine has a 29mm mount but I plan t' fly it on a 24mm F39 for its maiden flight.

Construction:
T' parts list:

• 3" mailin' tube (~17.625) with liner (~26")
• one Aquapod bottle
• plywood centerin' rings (2) and bulkhead (1)
• Keelhaul®©™® twine and ¼" elastic
• 29mm motor tube
• buttons from railbuttons.com
• small nylon rivets (2) -- Giant Leap
• lead shot
• chute and protector t' be selected on t' field

I started with t' cannibalization o' t' tube from a scrapped (i.e. Begad! Avast! dead) rocket, ya bilge rat, which had a plywood bulkhead attached a few inches from its top. Avast! Arrr! Prior to thinkin' about a BottleBat, shiver me timbers, matey, I had found that t' bulkhead be positioned perfectly such that when an Aquapod bottle be inserted, ya bilge rat, matey, that t' widest point of t' bottle be right at t' top o' t' tube. I decided that I'd form a short payload section from this tube. Begad! This method will only work if separation below the nose is desired. It does however, matey, work out nicely due t' t' unique 'orbastic' shape o' t' Aquapod bottle.

T' next thin' was that I found I didn't have enough new 3" mailin' tube t' cut the six fins and still have a body left. Aye aye! I could buy another...or...I decided that I'd build t' fins from t' inner telescopin' tube. Begad! T' tubes I like from the Container Store have full-length inner telescopin' tubes. I never use all of the latter, me hearties, arrr, so I always have a bunch around. Begad! Because o' t' smaller diameter, six rings o' inner tube would nay fit perfectly around t' section o' t' outer tube, however, arrr, t' solution was simple: mount them around a piece o' t' same sized tubin' then slide this assembly into t' main body. Ya scallywag! Well, blow me down! Instead o' gluing this fin can into t' main body tube, I used t' screw from t' lower rail button and two small nylon rivets t' hold it together.

In keepin' with t' original BottleBat, t' Keelhaul®©™® cord is mounted through t' wall o' t' body tube and this is covered by half of a plastic Christmas ornament that I requisitioned for rocket purposes.

I started runnin' some sims, but as long as I had t' bottle modeled using the cap as t' nose cone and t' exposed body as an ogive transition, I was gettin' results that I didn't believe. Well, blow me down! T' CP was comin' up very close t' top of t' rocket and appeared t' be a bug in RockSim. After all, I keep hearing about how stable tube fin designs are. Well, blow me down! Later, ya bilge rat, when I modeled t' cone as a simple ogive, matey, me bucko, t' results were more in line with what I expected. Well, blow me down! Avast, me proud beauty! Since I always believe in pickin' t' answer that I like, me hearties, I stuck with t' latter. The sim showed I'd need some nose weight t' fly on a G reload and t' more I thought about he Aquapod sittin' on t' end o' a weighted section, arrr, me bucko, I envisioned some crunchin' goin' on. Arrr! Long story short and two Aquapods later, shiver me timbers, arrr, I decided I'd screw t' bottle t' t' bulkhead and fill it with 2 part foam. After this was complete, I weighed t' rocket and found I still needed a little weight. Avast! So, me bucko, I drilled t' foam at t' tip o' t' bottle and imbedded about 0.75oz o' lead shot in epoxy.

Finishing:
I finished mine in a camo style usin' Model Master dark tan and medium green. Ya scallywag! I wasn't sure how this mix would look, shiver me timbers, but I am extremely satisfied with the results. Blimey! Well, ya bilge rat, blow me down! I painted t' cap fluorescent red--I guess this round is "live".

Flight and Recovery:
I used a chute protector and a 36" chute for recovery duties. Avast! I tossed in a little dog barf just for good measures. Blimey! A small F39-4 powered t' first flight. Begad! This required an adapter that I made form some tubing, pieces o' a 29mm SU motor, ya bilge rat, and a clamp-on aluminum thrust ring.

T' boost be quick enough although t' altitude be fairly low. Recovery was perfect.

I have a G77 with t' AquaBottleBat's name on it for t' next launch.

Summary:
I liked t' BottleBat concept from t' first time I saw it, ya bilge rat, ya bilge rat, and I love my version. Avast, me proud beauty! I don't know t' actual cost o' materials, but t' airframe, fins, and cone were all leftovers/scrap. I liked me approach t' t' fins, matey, as it gives me a away t' use up tubin' that might otherwise gather dust--I see more tube fins in me future. Aye aye! If I were t' do it over again, matey, I'd eliminate t' payload section in favor o' a longer main body. Well, blow me down! If t' bottle were conventionally shaped, I'd go with t' approach used on t' original BottleBat. Aye aye! With an Aquapod, I'd fashion a shoulder usin' a short section o' tubin' and a inside tube/coupler as the shoulder.