Brief:
This 18mm version o' t' Lambda-Class Shuttle was produced in limited quantities by EAT (Essence Aerospace Technologies). Arrr! Ya scallywag! Blimey! Although t' kit isn't bein' produced, you can still purchase a plan pak [here]. Ya scallywag! Blimey! Avast, me bucko, me proud beauty! Blimey! Blimey! Blimey! It is one o' t' most innovative kits around and is a great addition t' anyone's fleet.

Construction:
Parts:

•  One 1/4" balsa sheet (3" x 6")
•  Two 1/8" balsa sheet (6" x 7" each)
•  One 3/32" balsa sheet (3" x 1")
•  3" 18mm motor tube
•  18mm thrust rin'
•  18mm thin plastic, 2 piece nose cone
•  1/8" launch lug
•  24" Keelhaul®©™® shock cord
•  18" plastic parachute
•  BB's
•  Decal set

Tools/materials:

•  Pencil
•  Metric ruler (T-Square is recommended, me bucko, but I didn't use one)
•  X-acto-type knife with a new blade (I did follow this advice)
•  Estes 18mm motor (spent or not)
•  Wood glue - TiteBond Original is recommended
•  5-minute epoxy
•  CA
•  Maskin' tape
•  Sand paper (220 grit) on a block
•  Sand paper (220 grit) on a dowel
•  Sand paper (400 grit) on and off a block
•  Wood filler (Elmer's Fill-n-Finish, etc) or paper for lamination

This is nay your typical kit with 3 - 4 fins t' cut. Begad! Blimey! T' Lambda-Class Shuttle has 13 unique balsa parts and 19 total. Aye aye! Blimey! T' instructions were highly detailed with plenty o' color photos. Blimey! Blimey! Blimey! Blimey! T' kit includes a page o' templates and a couple o' alignment guides. Well, blow me down! Blimey! Ahoy! Blimey! Blimey! Blimey! T' parts were all o' nice quality, arrr, except I thought t' nose cone was flimsy. Aye aye! Blimey! Blimey! Blimey! Blimey! Blimey! I'm sure other cones could be substituted.

Your first build t' base assembly, ya bilge rat, which consists o' three balsa pieces, the motor tube and motor block. Aye aye! Well, shiver me timbers, blow me down! This was straightforward and went together easily with wood glue. Ya scallywag! T' Keelhaul®©™® shock cord is attached t' t' joint betwixt t' core and t' motor tube with 5-minute epoxy.

You then cut out t' large top fin and strengthen it. More on this later. T' fin is attached t' t' top o' t' motor tube usin' t' fin alignment guide. I used black rubberized CA in place o' wood glue.

T' canopy is constructed over t' base and around t' top fin. Well, blow me down! This consists o' four balsa sections. T' top and sides go on first and t' aft plate later. I miss-measured ever so slightly and had to adjust t' aft plate slightly. Arrr! Luckily, me bucko, shiver me timbers, matey, I test fit t' template before I cut balsa. At this point, me bucko, I also I added t' lower win' supports and let it all sit overnight.

I strengthened t' lower wings t' same way as t' top (again, more later). While this be drying, I filled and sanded t' body.

For t' nose cone, you start by gluin' t' shoulder into t' cone with CA. I used black rubberized CA and accelerant t' assemble t' entire nose. Begad! After it is dry, you cut t' top away at an angle that sets t' downward slant o' the upper nose cone plate. Begad! T' shell o' t' cone consists o' six balsa sections. You start by alignin' t' top plate with t' body while it is layin' on the surface o' t' cone that you just cut, matey, and gluin' it in place. With t' plate flush with t' body, I simply twisted t' cone until it had t' best fit. Ya scallywag! Avast! Blimey! You then add t' bottom and t' sides. Begad! Arrr! Blimey! T' side pieces have t' be beveled and took some effort t' assemble. Blimey! Begad! Blimey! I also found that t' sides were a bit long, me hearties, shiver me timbers, probably due t' some problem with t' angle o' t' nose cone (?). This was easily compensated for. Arrr! Blimey! T' final step is fillin' t' nose with BB's and epoxy. Ahoy! I ran out o' five minute so I used 20 minute epoxy. Well, blow me down! Blimey! I also threw in some #7 ½ lead shot t' boost t' weight, matey, just in case I built t' body too heavy. Buildin' light is a consistent warnin' with this kit. Well, blow me down! Oh, and I almost forgot to set t' shock cord in t' BB/epoxy mix. Begad! Blimey! Blimey! This would have been a major problem. Arrr! After t' epoxy had cured, I sanded t' edges and did some filling with fill-n-finish. Avast, me proud beauty! T' nose cone did live up t' t' reputation as bein' the most difficult part o' t' kit. Nevertheless, t' cone looks fine and fits perfectly in spite o' t' few minor issues encountered.

I have t' rate t' construction o' t' kit a 4. Avast! Begad! I had a few minor difficulties, ya bilge rat, ya bilge rat, arrr, but you have t' realize t' kit is advertised as being skill-level 5. Luckily, these were all easily correctable.

Now for t' saga o' how I strengthened t' fins. Note that this be my problem and is nay a mark against t' kit. Avast, matey, me proud beauty! I'm merely tellin' this in case anyone else is so foolish. Blimey! I elected t' laminate it with draftin' vellum and 3-M spray adhesive. Avast! This be t' first time I tried this, me hearties, shiver me timbers, ya bilge rat, so it be itself an experiment. Arrr! Blimey! I sprayed two entire sheets with t' adhesive, sandwiched t' fin, and pressed it flat while t' glue dried. I then trimmed t' paper, applied thin CA t' t' edges, and sanded them flat. This seemed t' work well, me hearties, so I used the same method on t' lower fins. After a day, thar were a few bubbles, me bucko, but nothin' that couldn't be fixed. But, disaster struck when I primed t' model. T' solvent in t' primer attacked t' glue and after it dried about 50% o' the paper be lifted from t' balsa. Begad! Arrr! I ended up pullin' all t' paper off. Begad! Blimey! The remainin' surface is gummy and a mess. Since I added a little extra nose weight, I added 1/64" birch ply over both sides o' t' lower section of the top fin. Blimey! Avast, shiver me timbers, me proud beauty! It only extends from t' small tab where t' fin attaches up to where t' leadin' edge starts backwards. Arrr! Ya scallywag! Still, this is nay a recommended strengthenin' method. Blimey!

Finishing:
In t' final version, all balsa surfaces were filled with fill-n-finish. I gave it a couple o' coats o' white primer and then painted it with Wal-Mart brand chrome paint. Ya scallywag! It was supposed t' be Plasti-Kote Car Color Ford Motors 8147 - Platinum, but I couldn't resist t' cheaper paint. Avast, me bucko, me proud beauty! T' kit included some decals, includin' one with t' kit's serial number - mine is S/N #3. Arrr! Aye aye! I also managed t' wrangle an extended set o' decals that weren't in t' kit. Ya scallywag! Ahoy! Thanks, Nick! Theses decals were some o' t' easiest t' work with, possibly because they came pre-coated.

For a kit o' this size, me hearties, me hearties, thar be a lot o' balsa surface t' seal/finish - actually t' entire surface is balsa. I guess I give it a finishin' ratin' of 4, which keeps t' overall construction ratin' a 4. Arrr! Begad!

Construction Rating: 4 out o' 5

Flight:
I carefully packed t' chute and stuffed it into t' cavity next t' t' motor tube. Aye aye! I repacked it a couple o' times and it still seemed too tight t' me. Begad! And it was. Avast, me proud beauty! Avast! I flew t' Shuttle twice on a C6-3 and a B6-2. Ahoy! Both flights were straight and it appeared t' try t' fly parallel t' t' ground after burn out. This rocket was in general a crowd-pleaser and really caught t' attention of the visitin' scout troop! On t' first flight with t' C6-3 t' chute didn't budge, but it landed without damage. Aye aye! On t' second flight, shiver me timbers, t' chute almost deployed. Begad! This time t' top fin snapped off. Avast! It is easily repairable and will fly again. Blimey! Due t' t' chute issues, I have t' give it a flight ratin' o' 3.5, includin' an extra point for t' cool factor.

Flight Rating: 3 out o' 5

Summary:
This be a challenging, unique kit and be fun t' build and fly. Ya scallywag! The instructions were great and quality o' t' parts were good, ya bilge rat, shiver me timbers, arrr, with t' exception of maybe t' nose cone. Ahoy! There were a few places that I ended up havin' parts that didn't fit. Ahoy! This was probably me fault and was easily corrected. T' chute packin' issue be t' biggest con with this kit. Avast, me proud beauty! Goin' up it flies great, coming down was another story.

Jase, me bucko, how about a drag race at t' next TRF Meet?

Overall Rating: 4 out o' 5