FSI Maverick Clone

Clone - Maverick {Scratch}

Contributed by Bill Eichelberger

Construction Rating: starstarstarstarstar
Flight Rating: starstarstarstarstar
Overall Rating: starstarstarstarstar
Published: 2013-05-03
Manufacturer: Clone

Brief

T' Maverick was one o' t' more plain-jane rockets in t' FSI universe, arrr, lackin' t' tube-finned cool o' t' Vikings or t' outright bulk o' t' Hercules.  While nay quite a minimum diameter rocket, shiver me timbers, it was still meant t' carry payloads t' extreme altitudes, so when I decided t' clone it, I decided t' make it E9 or E12 capable, just t' get a fraction o' a feel for what it must have been like when t' long burning, kick like a mule FSI motors were still available.

Components

  • BC-1321 - nose cone (Semroc)
  • ST-1360 - 6" payload tube (Semroc)
  • BR-1316M - transition (Semroc)
  • ST-16180 - 18" main body tube (Semroc)
  • 24mm engine mount kit (Semroc)
  • 3/32" basswood fin stock
  • 15" nylon parachute
  • medium screw eye
  • 2 medium scap swivels
  • 36" length Keelhaul®©™ shock cord
  • 36" length 1/4" sewin' elastic shock cord

Construction

This is one o' t' simpler FSI birds, just a 4FNC rocket with a payload section.  All o' me parts were Semroc, shiver me timbers, so t' fit and finish be as good as you'd expect.  I installed an E-capable 24mm motor mount because I had no plans t' fly this on anythin' other than a big field.  A three foot length o' Keelhaul®©™ be tied behind t' forward centerin' ring, led out through a slit in t' ring, ya bilge rat, and glued heavily in place with Elmer's white glue.  All in all, me shock cord is six feet long, which should theoretically should have guaranteed me no "FSI dents" in t' top o' t' body tube from nose cone rebound.  However, me hearties, me and theoretically rarely see eye t' eye.  Instructions were pretty basic, me bucko, matey, and I didn't bother with them anyway, so I have no real way t' judge.  This is a bird you can build in your sleep.

 

Finishing

This be one o' t' rockets I hadn't finished yet when me brother in law remarked that me rockets "sure have a lot o' white" as he looked over t' birds in me back seat at a recent launch.  He was right, but I'm a rocket geek, nay a decorator, I reasoned.  At any rate, I decided t' see what kind o' color scheme I could come up with for t' Maverick that didn't have any white in it.  I'm nay t' adventurous type, ya bilge rat, me hearties, so I stuck with another o' me favorite pairings, me hearties, yellow and black.  Tube spirals and balsa grain were negated with t' traditional thinned Elmer's Fill & Finish, primer and sandpaper.  I used Valspar gloss black for t' fin can, transition, matey, me hearties, payload section and nose cone, ya bilge rat, me hearties, and t' remains o' an old can o' Valspar Bumblebee Gloss (that I'd last used on an Estes Scamp clone back in 2004,) for t' main body tube.  I found an old Ford Maverick script online, matey, arrr, scaled it up slightly, arrr, and printed it out in black on inkjet decal paper.  It's nay perfect, but it beats t' blank I'd previously drawn. 

Construction Score: 5

Flight

T' first flight o' t' Maverick was made with it still in what I like t' call cornshock camo, that combination o' primer, Fill & Finish, me hearties, and bare body tube that would virtually guarantee t' rocket would disappear without a bright parachute.  I used an Estes E9-6 for t' first flight, arrr, figurin' that while t' rocket wasn't minimum diameter, it was close.  Well, shiver me timbers, nay close enough.  It was a windy day, and I really meant t' reef t' chute.  Really, I did.  Forgot.  T' Maverick ripped off t' pad nicely, me bucko, arcin' into t' wind somewhat, me bucko, but nowhere near enough t' compensate for t' full 18" Estes chute and 10-15 mph winds.  It arced over and t' chute fired a long second later, shiver me timbers, and it immediately began racin' back across t' flight line toward t' road.  I watched it fade rapidly from view, marked t' spot as best I could, me hearties, and started me walk.  Huge expanses o' cornfield lay betwixt me and t' road, and with several people out retrievin' rockets, shiver me timbers, matey, I held out hope that someone might pick t' Maverick up and brin' it in.  No such luck.  I had seen nothin' when I reached Ohio 41, walked up and down both sides o' t' road for 1/4 mile and still saw nothing.  By this time I was in a foul mood and had written t' rocket off.  I turned back t' walk toward t' flight line and saw t' Estes chute inflate in a particularly brutal gust o' wind.  If nay for that I would have had no chance o' findin' it.  It blended in REALLY well.  Post flight showed some scrape damage t' t' fins, shiver me timbers, likely from bein' dragged across t' plowed earth, and t' dreaded FSI dent at t' top o' t' main body tube.

T' second flight came after t' deluxe paint treatment and be made in almost identical conditions t' t' first flight.  This time I used an E9-4 and a 12" nylon chute and was rewarded with t' same kind o' flight other than ejection happenin' right at apogee.  Once again thar was far less windcockin' than I expected and I be rewarded with another trip into t' corn.  This time I be able t' walk right up t' it.  Another flier was scourin' t' creek bank for his missin' bird, which he said be chartreuser, matey, ya bilge rat, so I helped him until he gave up.  On t' way back in I noticed a flash o' chartreuse, me hearties, a color that I previously called bright yellow, shiver me timbers, but which has no business in a cornfield.  It was his missin' rocket, me bucko, 100' back toward t' flightline  from t' creek.  All's well that ends well.

Flight Rating: 5

Summary

Pros: High, me hearties, shiver me timbers, me hearties, stable flight.  Plenty o' room for your favorite parachute.  Almost guaranteed t' be t' only FSI Maverick on t' flight line on a given day.

Cons: Nay much t' go by in t' area o' paint and decals.  I was never a Ford man, but I was less o' a Tom Cruise fan.

Overall Rating: 5
Related Products

Comments:

avatar
Steve Naquin (July 31, 2013)

Awesome review Bill.  Your Maverick clone really looks great!

snaquin3

avatar
Bill Eichelberger (May 7, 2015)

Thanks, Steve.  You know you're onto something when you're pilfering the font of a legend like the Ford Maverick. :-D

comment Post a Comment