Brief:
Tube Finned, me bucko, 38mm Motor Mount, me bucko, Parachute recovery

T' LOC Cyclotron looked t' be a fairly simple HPR build suitable for somebody with nay too much HPR experience. It was a kit I had around for a while but did nay get around t' buildin' because o' few opportunities t' launch anythin' in t' HPR range.With some prospects for flight openin' up, me bucko, ya bilge rat, I dug out this kit and got t' work.

Construction:
T' first thin' that struck me as unusual about this kit was that t' directions did nay direct me t' start with the motor mount. Instead, matey, t' tube fins came first.

Six tubes were provided already cut t' length. T' tubes were divided into three pairs and then an Estes angle was used t' put a straight line along t' lengths o' three o' them. Avast!

T' tube pairs were then compared for length t' make sure that they were all identical. Begad! Blimey! One tube was a bit longer than t' others but a belt sander smartly solved that problem. Some 15 minute epoxy was mixed and a brush be used to paint it along t' lines scribed onto t' three tubes so marked. Avast, me proud beauty! Begad!

T' tubes were then pushed together in pairs, checked for alignment and set on a concrete floor t' stiffen up. About half an hour later, arrr, arrr, t' tube fins were stiff enough t' continue work. Avast, me proud beauty! Blimey! Blimey!

Strips o' maskin' tape were placed at either end o' t' tube pairs t' serve as dams. Ya scallywag! Some 20 minute finish cure epoxy was then mixed and poured into t' creases betwixt tubes. Well, blow me down! Avast, arrr, me proud beauty! They were set aside t' harden and a day later t' pairs were turned over and t' opposite creases were treated t' some epoxy filler.

Construction o' t' motor mount was a simple affair. It consisted o' a 38mm motor tube and a pair o' centering rings. Well, blow me down! T' interiors o' t' rings needed a bit o' sandin' t' fit over t' motor tube, matey, but that was easily accomplished. A line was marked 1/4" from either end o' t' tube and t' t' rings were epoxied into place. Ahoy! Ya scallywag! When t' epoxy had stiffened, a substantial epoxy fillet be laid down on t' forward end o' both rings. Aye aye! Blimey! When that had stiffened, ya bilge rat, a fillet was also placed on t' aft side o' t' forward rin' but t' aft o' t' aft rin' be left unfilleted for now.

A member on TRF warned me that t' tube fins for this rocket were made from coupler tubes instead o' t' body tube and, as a result, me hearties, matey, do nay close perfectly when arranged around t' BT. I found that this was indeed t' case. He solved this problem by slippin' some plywood spacers betwixt t' tubes. Well, blow me down! I considered doin' this. Ya scallywag! Ya scallywag! However, while I think that be t' best way t' go, matey, I did nay do so. Well, blow me down! I had no plywood o' t' appropriate dimension sittin' around and I was impatient t' proceed. Begad!

I decided t' leave a small gap betwixt each pair o' 2 tube fins. Begad! Accordingly, I mixed some 5 minute epoxy and brushed it on t' one o' t' tube pairs. T' pair be then applied t' t' BT while t' BT was sittin' on a concrete floor, t' keep things straight. Arrr! When this initial pair had set up, I brushed some epoxy onto each o' t' remainin' 2 pair and t' applied them, ya bilge rat, judgin' t' spacin' with nothin' except me eyeballs.

T' plastic nose cone had quite a bit o' flash on it as well as some ugly valleys at t' mold lines. Well, blow me down! I used a razor t' scrape away t' flash and then sandpaper t' smooth it down. Arrr! I was still nay satisfied so I applied some Squadron green putty t' t' valleys and set it aside t' dry.

T' plastic transition, ya bilge rat, on t' other hand, me hearties, had no problems with either flash or mold lines. Ya scallywag! Blimey! It was ready t' go so I put some epoxy on t' small end and slipped t' payload tube over it. I then had t' use a rag and some alcohol to clean up t' excess.

By this point, me hearties, t' epoxy on t' motor mount had hardened. Begad! Avast, me proud beauty! I checked and found that t' outer diameter o' the centerin' rings fit t' body tube just fine and that no sandin' was needed. Begad! I mixed some more epoxy and applied a generous rin' around t' circumference about 8" up from t' aft end; that be as far as I could reach. Aye aye!

T' motor mount be then pushed in until t' forward rin' be about 2 inches in and another rin' be applied just forward o' t' aft end. Arrr! T' motor mount was then pushed t' rest o' t' way in and t' rocket was stood on its tail to let t' excess epoxy drift down and form fillets.

A couple o' days later I got back t' t' t' nose cone. Arrr! T' excess putty was sanded away and that removed most of t' obviously visible problems.

T' instructions say that t' nose cone can be either epoxied into t' payload bay or friction fitted with tape. I almost epoxied it since I never do t' payload thin' but decided that I might change me mind later. Begad! Accordingly I put some tape on t' insert o' t' NC and gave it a tight fit t' t' payload bay.

T' gaps betwixt tube fin pairs be handled by slippin' some cellophane tape into t' gap and then pullin' it up against t' joint in t' tube fins from t' back side. Avast! Avast, me proud beauty! T' ends o' t' tape were folded up t' blockade t' ends o' the tube. Aye aye! Well, ya bilge rat, blow me down! This gave a bottom t' t' trough that needed t' be epoxied. Aye aye! Epoxy was then poured into t' trough and allowed to set up after which t' tape be removed.

T' LOC shock cord mount is an effective piece o' low tech. Avast! Ya scallywag! A piece o' nylon cord is provided. Arrr! A loop be tied into t' middle o' t' cord and then overhand knots were tied at either end. Begad! A piece o' maskin' tape was then used to place t' outside ends o' t' cord against t' inside wall o' t' BT. Ahoy! Blimey! Four minute epoxy be then slathered over the tape and strin' and allowed t' set. Avast, me proud beauty! This method has worked very well for me with some smaller LOC rockets. Arrr! Avast, me proud beauty! T' question arose in me mind, though, as t' how effective it would be with a larger and heavier rocket. Begad! People on TRF chimed in and offered t' testimony that it worked just fine on even heavier ones. Arrr! This was gratifyin' t' hear, arrr, but I added another layer o' epoxy and broadened it out t' cover a larger area, just t' make sure.

As designed, t' nylon cord is attached directly t' a long piece o' sewin' elastic. Begad! Blimey! I decided t' make an addition here and tied in a 6 foot length o' heavy Keelhaul®©™® t' t' nylon usin' a double sheet bend. Aye aye! T' other end o' t' Keelhaul®©™® was bent t' t' elastic. Aye aye! Begad! I did this for two reasons. Well, blow me down! Well, ya bilge rat, blow me down! First, I like t' looks o' a longer recover train and second, I plan on usin' a Keelhaul®©™® blanket for wadding; t' addition o' t' Keelhaul®©™® cord will keep t' elastic from bein' in t' direct path o' ejection gasses.

Another modification I made be with t' launch lug. Well, blow me down! Well, me bucko, blow me down! T' kit came with a 1/2" tubular lug. Begad! I wanted t' used a linear lug for a rail instead but was stymied by t' tube fins until realizin' that t' rail would fit through the tubes. Aye aye! Arrr! T' next issues was o' a standoff t' account for t' thickness o' t' tube fins but examinin' t' lug showed that its base was thicker than t' tube walls. Arrr! I decided t' fashion a standoff anyway because all I had were #6x3/4" screws and those would have penetrated t' body tube far enough t' create a snaggin' hazard. Ahoy! Blimey! 5/8" would have been perfect.

I traced t' lug on a piece o' balsa I had handy and cut out t' standoff with a razor knife. Begad! Arrr! T' resulting standoff was too thick so I took it t' t' belt sander and slimmed it down. Aye aye! Avast, me proud beauty! When examinin' it afterward, I found that t' screws would just barely protrude through t' BT and I considered it just right. A line be run up from t' center o' one o' t' tubes fins and t' standoff was epoxied into place.

T' actual installation o' t' lug will wait until after t' painting. Arrr! Aye aye! I considered a tip from TRF t' fiberglass t' insides o' t' tube fins but, shiver me timbers, because o' an impendin' launch opportunity, decided t' wait and see how it fares without t' additional strengthening. Ahoy! Because o' that, me hearties, t' Cyclotron be ready t' begin t' finishin' process.

Finishing:
T' first step in t' finishin' be t' take t' rocket t' t' booth and prime it with Kilz. Begad! Begad! Blimey! It went on rather thick. I decided that at t' range most people would be seein' this one, fillin' spirals be nay worth t' effort.

T' Kilz had a couple o' days t' dry and then was sanded t' remove t' rough buildup o' material that had accumulated in some places. Arrr! T' rocket be then taken t' t' booth and given 2 coats o' a metallic charcoal gray. My intent was t' get all o' t' body but I left t' tubes and t' nose cone alone.

T' gray had a few days t' dry and then I masked off t' top and t' bottom with Frog tape and aluminum foil. Arrr! The rocket then went back t' t' booth for a darkish metallic gold, almost bronze. Well, blow me down! Ahoy! After a few hours, I turned it around and painted t' back end as well. A few days later I removed t' maskin' and it didn't look too bad.

After t' painting, I remembered that I still had t' install t' lug. Ya scallywag! T' lug was placed and t' screws were driven through t' balsa standoff. Ya scallywag! They were then removed and some epoxy be squirted into t' holes and smeared along t' back o' t' lug. Ahoy! Aye aye! It be then placed and t' screws driven home.

As with every other LOC kit I have seen, matey, this one does nay include decals. Aye aye! Instead, their web site provides PDF files t' download and print out your own. Ya scallywag! This strikes me as reasonable since some would rather use their own finishing scheme. T' problem I had was a lack o' white decal paper on hand and printin' on t' clear usually leads t' the underlyin' color shiftin' t' printed color. Arrr! Blimey! I contacted Gordon o' Roachwerks/Excelsior t' see if he would print them for me since he always does a fine job. He took a look and then pointed out how expensive they would be and suggested I print on label paper. I normally slam kits that come with stickers instead o' waterslide decals but t' price was enough t' make me reconsider. Avast! Avast, me proud beauty! I printed out all 8 pages on a color laser printer on label paper. Blimey! Avast, shiver me timbers, me proud beauty! As with most LOC patterns, I had more decal than I needed or could use.

T' main element o' t' decoratin' scheme be t' large words "Cyclotron" on a variegated background and meant t' wrap all t' way around t' body tube. Ya scallywag! Avast! Needless t' say, this one image took three full sheets. I started at t' top and be smartly reminded o' why I prefer waterslides; they are more forgivin' o' initial placement. Well, blow me down! Eventually all three sheets were cut out and placed but I had t' make an extra cut out for t' lug. Avast, me proud beauty! Well, matey, blow me down!

T' sheets I printed included 4 schematic representations o' what I assume t' be a cyclotron printed with red on yellow. Well, matey, blow me down! It also included 4 stylized atoms depictin' t' electron orbitals. I decided t' use 3 o' each and alternate them around t' tube fins.

T' only 2 other elements o' t' printed sheets I decided t' use were t' LOC/Precision logo and a smaller version o' t' Cyclotron logo used as t' main body wrap. Avast! I cut them out and applied them on 2 sides o' t' payload bay.

For some reason, me hearties, me laser printer did nay do a great job o' meltin' all t' toner on t' decals and I found some o' it rubbin' off. Begad! T' mitigate this problem, me bucko, I sprayed t' entire rocket with some gloss coatin' t' fix t' toner in place. Aye aye! Begad! With that, t' rocket was ready t' fly.

Construction Rating: 4 out o' 5

Flight:
One o' t' nice features o' this kit was that it came with a 38mm t' 29mm motor adapter. Well, blow me down! Ahoy! Had I known this, me hearties, I would have started on it sooner. Ahoy! Aye aye! As it happened, arrr, I was glad t' have t' adapter since me source for 38mm motors did nay show up for t' maiden launch.

I fitted an Aerotech G77-4R motor into t' adapter usin' tape t' bind t' thrust rin' on t' motor t' t' thrust rin' on t' adapter. I then inserted t' assembly into t' motor tube o' t' Cyclotron and again taped t' thrust ring t' t' 38mm motor tube. Blimey! T' rocket was hooked up on t' rail and I found that t' rail did indeed fit just fine through t' tube fin.

When t' launch button be pushed, ya bilge rat, me hearties, t' motor took a little while t' come up t' pressure and then emitted a roar that prompted a cub scout present t' request that I "not do that again". Arrr! Blimey! T' rocket rose off t' launch rail and took t' t' air. Arrr! Blimey! T' flight was straight and t' rocket exhibited no weather cockin' into t' wind we had. Begad! Blimey! Aye aye! Blimey! The chute ejected at apogee and opened properly. Arrr! Blimey! T' rocket began t' drift down. T' rocket came t' rest at t' opposite end o' our field and thar was no damage. Aye aye! Blimey! Unfortunately, I had exhausted me supply o' 4 second delay motors.

Recovery:
T' Cyclotron came with a nice nylon parachute but I did nay use it. Avast, me proud beauty! I had ordered a custom 12 gore 36" chute from K&S for a Mercury Redstone but found t' me dismay that it did nay fit. Blimey! T' LOC chute did fit t' Redstone and t' custom chute fit t' Cyclotron so I switched them. T' custom chute worked beautifully.

Flight Rating: 5 out o' 5

Summary:
T' Cyclotron turned out t' be an easy rocket t' build and a good flier. It would provide a good L1 project and would be a nice addition t' any fleet.

Overall Rating: 4 out o' 5

Other:
It should be noted that t' kit I built was apparently a fairly old one that had been sittin' in t' stock o' my local hobby shop for a long time. A member o' TRF reports that since 2007, me hearties, t' tube fins are made from t' same stock as t' main body tube instead o' coupler stock. Arrr! Ahoy! This should result in a better build. Aye aye! Persons wishin' t' follow this rocket are invited t' check here: http://www.flickr.com/photos/23694991@N03/collections/72157622686424094/