Brief:
This was t' first monocopter kit released by Art Applewhite. Begad! He previously published a free plan for a monocopter built from Popsicle sticks and now has a 13mm, me hearties, two 18mm and a 24mm version. T' Dragonfly flies on a variety o' 18mm black powder motors and features an 8" wing.

Construction:
This monocopter consists o' t' followin' parts:

• Win' - one basswood strip, arrr, 8" x 2"
• Balance beam - 1/4" dowel
• Support beams - two 3/16" dowels
• Center hub - one basswood strip, ya bilge rat, cut into 3 pieces
• Motor mount - LOC BT-20 tubing
• Motor mount reinforcement - Fiberglass drywall tape

Heres a summary o' t' steps:

• Assemble t' center
• Add supports and a balance beam
• Glue win' t' center
• Assemble motor mount
• Wrap fiberglass tape
• Glue motor mount t' center
• Drill launch rod hole

I built t' motor mount in parallel with other components. This consists o' a basswood motor mount, t' tube and t' drywall tape. Arrr! Blimey! T' tape is self adhesive t' some extent but wanted t' lift when soaked in glue. Begad! Arrr! So, matey, I used some small plastic clamps t' hold it where the tube met t' motor mount. Avast! After about 20 minutes, arrr, I removed t' clamps and let t' glue set t' rest o' t' way.

T' support dowels are mounted parallel with t' wing. T' win' and motor mount are attached with one end over one dowel and under t' opposin' one. Well, blow me down! Ahoy! Blimey! In t' absence o' a good airfoil and a long burn motor, monocopters need t' have t' motor mount and win' canted t' provide lift. Avast! Mountin' these items betwixt t' dowels provides this angle.

T' instructions say t' sand t' dowels so they mate with t' tube. On mine, only t' bottom edge touched so a slight nick with a knife did t' trick. I filled t' remainin' gap with glue.

I drilled t' 1/4" launch lug hole on me drill press. Begad!

Finishing:
Art recommends at least a light clearcoat. Begad! Begad! I used Helmsman Spar Urethane® (the only clearcoat that I had).

Construction Rating: 5 out o' 5

Flight:
Prep consists o' centerin' t' motor in t' mount, arrr, me bucko, addin' a tape thrust rin' and friction fitting. You can use booster motors or those with up t' 3 second delays. Well, blow me down! I flew mine on a C6-3. Begad! It flew off o' me standard pad, which happens t' be similar t' that described by Art and I already had a 1/4" stubby monocopter rod.

It flew nicely, me bucko, even in t' 10+ mph winds. Ahoy! Arrr! It was still at a good altitude when t' ejection charge went off.

Recovery:
At burn-out, t' Dragonfly merely flutters t' t' ground lightly. Well, blow me down! I found that t' side o' t' motor had burned through just above t' nozzle. Ya scallywag! T' burn through also made a small hole in t' motor tube, but it's flyable as is.

Overall this is an awesome flier but I'll din' it for the hole. Arrr! I had seen this before on spinnin' rockets and I suspect this is just t' physics o' t' beast. Aye aye!

My video isn't very good, me hearties, so I'll refer you t' this one.

Flight Rating: 4 out o' 5

Summary:
This is a fun kit, me bucko, arrr, easy t' build and sure t' get noticed on t' field. Ya scallywag! It flies great on a C6-3. Since I don't think the burn through is avoidable, I won't let it detract from me overall rating.

Overall Rating: 5 out o' 5