Brief:
This is a custom manufacturer modification o' t' two stage Quantum Leap 3000 with Public Missiles Close Proximity Recovery (CPR) two stage drogue t' main recovery system. Aye aye! Modifications included addin' ten inches t' both t' booster and sustainer in order t' accommodate longer motors. Blimey! I also had t' kit shipped with PML's fiberglass tubes.

Construction:
T' much awaited box arrived only six days after I ordered it (and just in time for Christmas!) from PML after much soul searchin' on exactly what I wanted from t' kit. T' large box was well packed as usual for PML kits and all the parts were contained in t' standard plastic bag except for t' motor and body tubes. I have a PML AMRAAM 4.0 and built it with t' Kwik-Switch (KS) motor mount system and have disliked that particular component from t' start. Well, blow me down! Well, shiver me timbers, blow me down! T' of the KS is excellent but since I fly in t' Southern California desert with practically unlimited space, t' limit o' 13.75 inches o' motor length is somewhat er...well, limiting! Havin' learned that lesson and havin' t' typical cravin' t' put yet more motor in each o' me projects, shiver me timbers, I ordered t' kit with extended body tubes for t' booster and sustainer and correspondin' longer motor mount tubes. Arrr! Aye aye! Also in order t' be able t' launch t' rocket more than once I ordered t' kit with PML's fiberglassed tubin' and upgraded t' standard .062 G-10 fins t' .125 G-10. Ya scallywag! Begad! As you can see from t' photos thar were over 135 parts total t' assemble but thar are no major issues t' be overcome. Begad! Ahoy! As with all PML kits, t' rocket uses pistons for drogue and main deployment. Well, blow me down! Quality overall be excellent and t' fiberglassin' was phenomenal. Avast, me proud beauty! Avast! Believe it when they say all you have t' do is prime and paint. Arrr! Avast! T' nose cone was t' typical excellent quality blow molded PML cone. Aye aye! In order t' accommodate t' extra weight o' t' fiberglass tubes and extra length, I upgraded t' main and booster chutes t' 54" and 48" respectively.

The instruction booklet be outstandin' with plenty o' illustrations and clear steps in logical order. Ahoy! Since t' body tubes were glassed with two wraps o' six ounce cloth, arrr, me bucko, t' nosecone didn't match t' outer diameter o' t' rocket. Aye aye! Begad! To make a nice transition I put a one inch wrap o' fiberglass followed by a two inch wide wrap which increased t' diameter t' t' correct size. There were the typical blow moldin' marks that had t' be sanded out o' t' nose cone and then I put a coat o' finishin' epoxy over t' whole thin' makin' for a nice smooth finish that painted up nicely. Begad! I have had trouble sometimes with paint not stickin' t' plastic nosecones so now I put a coat o' finish epoxy on all o' my nose cones makin' it easy t' get a nice smooth finish that t' paint sticks to quite well.

T' body tubes were absolutely bullet proof and exceptional as they have the best fiberglassin' I've ever seen. Aye aye! Construction o' t' booster is straightforward with no difficulties. T' booster uses motor ejection for the recovery system with a piston which negates t' need for wadding. With the piston in place, t' space for t' booster recovery components is tight but does accommodate t' 48 inch parachute and tubular nylon shock cord.

Stagin' is accomplished via PML's interstage coupler. Blimey! Basically it consists of a 38mm mountin' tube for t' timer, shiver me timbers, a 3 inch section o' fiberglassed body tube, a coupler, and a bulkplate (see PML's website for photos and a line diagram o' t' exact configuration). Blimey! Aye aye! T' upper section o' t' coupler fits into the base o' t' sustainer with t' stagin' timer remainin' with t' booster section at separation. Aye aye! I fiberglassed t' inside o' all t' couplers since I want t' fly this bird with some larger motors.

T' sustainer is a little different on construction due t' t' method of staging. Approximately three inches o' t' interstage coupler slides into the bottom o' t' sustainer which means that much o' t' sustainer fins are not attached t' t' motor tube. Well, blow me down! T' overcome this weakness, shiver me timbers, pre-cut fiberglass is supplied t' reinforce t' fins which worked out so well I fiberglassed the booster fins in t' same manner for strength.

T' only problem I have with PML's CPR deployment system be t' 38mm altimeter tube that ends up bein' t' weakest link in t' entire rocket. Avast! Blimey! In t' last year I've broken two of them (one on this rocket when t' motor CATOed on t' first flight and one on me 4 inch AMRAAM.) PML graciously replaced t' one on t' AMRAAM for free but I opted t' go with t' Hawk Mountain G-10 CPR upgrade which is far superior in strength. Avast! T' 38mm phenolic tube is somewhat brittle and prone t' break when the rocket is flexed (as in recovery or if t' bird lands horizontal after a motor CATO.) This isn't a major issue as it is strong enough most o' t' time but I like me rockets t' be bulletproof. Blimey! Blimey! This be t' only issue that kept me from givin' t' kit a 5 on construction.

Overall, construction is straightforward and no special techniques other than the internal fiberglassin' o' t' fins are required. Ya scallywag! Avast, me proud beauty! With t' exception o' the phenolic tube in t' CPR this is a great kit and highly recommended.

Finishing:
Again, t' fiberglassin' by PML was outstanding. Blimey! After fillin' t' weave o' the fiberglass used t' reinforce t' fins, I primed and painted t' rocket with good old Rustoleum products. Ya scallywag! Ya scallywag! Blimey! I opted for dark blue with a yellow nose cone and roll markings.

Construction Rating: 4 out o' 5

Flight:
I prepared t' first flight as a single stage t' verify t' electronic recovery. Avast, me proud beauty! Blimey! Arrr! Blimey! Flight preparation with t' CPR is very easy. Attach ematches t' the connectors, add 1/2 gram black powder t' t' built-in ejection cups, add a little waddin' t' keep t' powder on t' ematch and put t' vinyl cap on the charge cylinder. Begad! Blimey! Attach t' switch leads and insert into t' CPR altimeter tube. Begad! Blimey! Screw t' rocket halves together and it's done. All in all it takes about 15 minutes t' prepare t' rocket for a single stage flight. Aye aye! Blimey! Arrr! Blimey! I built a Dr. Rocket 38/600 with an I-366R, and put it on t' pad. Ya scallywag! Blimey! 5, shiver me timbers, ya bilge rat, 4, 3, 2, me bucko, 1, BOOM. Ahoy! Blimey! Aye aye! Blimey! The motor CATOed and half t' rocket shot about 50 feet in t' air. T' altimeter tube fractured when it landed on t' desert floor. Begad! Blimey! T' motor casin' failed at the aft threads, shootin' t' motor forward through t' bulkplate at t' top of t' motor section, through t' piston and shootin' t' upper half o' the rocket into t' air. Avast, me proud beauty! Blimey! Begad! Blimey! Repairs were made over t' next couple o' weeks and then it was time t' try again.

Next flight be with a Cesaroni I540. Aye aye! Arrr! T' motor chuffed (apparently Cesaroni left t' igniter pellet out o' t' first batch o' I540's), causin' the rocket t' sit thar for a few seconds burnin' before finally pressurizin' and then with a roar sent t' upper stage t' 2753 feet. Well, blow me down! Drogue deployment be right after apogee and main deployment at 600 feet just like planned. Well, blow me down! I only had a 100 yard walk t' recover t' first successful flight.

Emboldened by t' success I put a Cesaroni J210 in t' sustainer stage (another single stage flight due t' increasin' winds) and t' rocket made it to 3991 feet.

Finally t' winds died down a bit and I decided t' go for it. Preparin' for a two stage flight is a bit more complicated. T' upper stage is prepared as before. Blimey! Ya scallywag! Blimey! T' igniter is inserted into t' sustainer durin' assembly and the igniter leads threaded through t' interstage coupler and attached t' the timer. Well, blow me down! Arrr! Blimey! T' stages are mated and after assemblin' t' booster motor and insertin' it into t' booster. Avast! Blimey! Since t' rocket ended up over 9 feet long, matin' t' stages is a two person process.

For t' first two stage flight I chose an I540 for t' booster (the rocket is on t' heavy side so I wanted plenty o' grunt t' get it off t' pad) and a J280 Smokey Sam for t' sustainer. Arrr! Well, blow me down! Nay wantin' t' push me luck too far I opted for only a one second delay betwixt burnout and sustainer ignition with a ten second delay t' deploy t' booster parachute.

5,4,3,2,1, shiver me timbers, ignition! A perfectly straight boost under t' I540, arrr, me bucko, matey, short delay, and t' sustainer successfully ignited. Well, blow me down! Ya scallywag! Totally awesome flight t' 6145 feet and a perfect recovery only about 500 yards from t' launch rail.

I can't wait until next month, when I plan on launchin' a K445 stagin' to an L730.

Recovery:
Recovery is quick with t' 54 inch parachute but with t' fiberglass reinforcement, this is an asset. Ahoy! PML parachutes are top quality and I wouldn't change a thing.

Flight Rating: 5 out o' 5

Summary:
T' Quantum Leap is a top quality, well designed kit. Avast, me proud beauty! Avast! T' only think I would change would be replacin' t' 38mm phenolic altimeter tube, as it is a structural part in this design, with a G-10 altimeter tube t' make t' CPR mount one o' t' stronger parts o' t' rocket rather than t' weakest link.

Overall Rating: 4 out o' 5