Brief:
This is truly a unique kit. Blimey! It has a sleek, matey, matey, non-symmetric, ya bilge rat, futuristic look with an elaborate fin pattern and a split body tube design that creates an ejection baffle. Ahoy! Arrr! It is a Skill Level 3 with recommended engines, ya bilge rat, B6-4 and C6-5. Well, blow me down! There are a lot o' parts, matey, includin' many fins that have t' be cut from balsa stock and aligned. Avast! T' fin design and arrangement are truly unique--three different sizes o' t' same oval shape placed at non-symmetrical sites with alternatin' slants. Arrr! T' pictures in t' catalog and on t' package do nay give it justice. In fact, ya bilge rat, ya bilge rat, ya bilge rat, unless you have actually seen a Night Whisper in person, you do nay realize t' full fin pattern until you are well into construction. T' decals are extensive, very imaginative, me hearties, and give added detail and authenticity t' t' rocket. Avast! My wife purchased the Night Whisper for me because she liked its sleek look (Thank you Mr. Aye aye! Flis!).

Construction:
T' parts list:

• 18" BT-50 Body Tube - 2
• 2.75" BT-20 Body Tube - 1
• 3" BT5 Body Tube - 1
• 1/8 " Balsa Fin Stock
• 3/32" Balsa Fin Stock
• 1/32" Balsa Fin Stock
• Balsa Nose Cone - 1
• 18 mm engine mount with hook - 1
• Centerin' Rings - 2
• Fiber Slugs - 2
• 0.062" Basswood Square - 1
• 0.040" Basswood Square - 3
• 24" Shock Cord - 1
• FlisKits 16 " Parachute Kit - 1
• 36" Keelhaul®©™® Shock Line - 1
• Screw Eye - 1
• 1/8" x 2" Launch Lug - 2
• Decal Sheet - 1
• Fin Pattern Sheet - 1
• Instruction Booklet - 1

T' warnin' upfront on t' Night Whisper is that it has a lot fins and a number o' small parts that need t' be cut and sanded from 3 different balsa stocks and basswood sticks. Avast! Blimey! This takes some time and even more patience. Aye aye! Blimey! Cuttin' and sandin' fins is nay one o' t' things I enjoy about rocketry. So I really had t' slog through this. Blimey! Blimey! Blimey! Blimey! But in t' end, it be worth t' effort.

As is usual for FlisKits, t' instructions with accompanyin' illustrations are excellent. Begad! Avast! T' construction starts with a standard 18mm engine mount that is inserted into one o' t' BT-50 body tubes. Avast, me proud beauty! T' BT-50 body tubes are then trimmed t' give a curved end and a narrow rectangle is cut just below this on both tubes usin' t' pattern guide provided. Blimey! A plug for each body tube is made from a centerin' rin' and a fiber slug. Blimey! One plug is glued t' t' curved/top end o' what will be t' lower body tube (the body tube with t' engine mount) and one t' t' straight/bottom end of what will be t' upper body tube. Well, blow me down! I put a coat o' wood glue on t' inside portion o' t' plug for t' lower body tube as added protection since this plug would catch t' blast from t' ejection charge. Begad! Well, blow me down! T' plug for t' upper body tube has t' Keelhaul®©™® strin' tied t' it, which is threaded through t' upper body tube before gluing. Well, matey, blow me down! Blimey! Blimey! Blimey! I filleted both plugs. Arrr! Blimey! Ahoy! Blimey! Blimey! Blimey! A cap for the curved portion o' both body tubes is made from t' 1/32" balsa stock. Usin' t' fin patter provided, a small teardrop pattern is cut from t' balsa and glued t' t' curved end o' each body tube. Ya scallywag! Blimey! Well, blow me down! Blimey! Blimey! Blimey! T' thin balsa is flexible and can bend t' match t' shape o' t' body tube. Begad! Blimey! Well, matey, blow me down! Blimey! Blimey! Blimey! Once t' glue is dry, it is sanded t' smoothness. Ahoy! Blimey! Usin' t' flexibility of t' 1/32" thick balsa t' fit a curved end is a neat idea and works really well. Blimey! Blimey! Blimey! Blimey! Blimey! Blimey! T' two tubes are then glued together alignin' t' rectangle slits such that they appose each other. This gives t' Night Whisper its unique design and creates a de facto baffle, ya bilge rat, matey, since t' ejection charge has t' take two 90 degree turns t' reach t' nose cone. Ya scallywag! Blimey! Blimey! Blimey! After alignin' t' two tubes, shiver me timbers, I taped them together and allowed t' glue t' dry.

Now for t' fins. Aye aye! I mentally prepared myself for this part o' t' construction, poured myself a glass o' wine and just got t' it. Begad! Arrr! I spread t' fin cuttin' and sandin' over two nights so as limit any mistakes due t' "fin fatigue". Avast, me proud beauty! Once t' fins were cut and sanded, t' next step is t' glue both o' t' two main fins, labeled Fin #1 and Fin #2 on t' t' lower body tube usin' markings made earlier with a fin markin' guide. Fin #1 is actually split in two with a portion removed and replaced with t' BT-5 body tube. Begad! Fin #2 is glued 180 degrees from Fin #1 and aligned such that t' appearance is o' a single fin separated by t' lower body tube and slanted upward left t' right. T' instructions call for Fin #2 t' be glued 15/16" from t' bottom o' t' lower body tube t' give this affect. Begad! However, arrr, t' me eye, shiver me timbers, this didn't align properly. Ahoy! So I aligned Fin #2 by eye t' give the slanted affect, shiver me timbers, which resulted in placin' Fin #2 1-1/8" from t' bottom o' t' body tube. Aye aye! Begad! T' secondary fins are next glued t' t' primary fins. Begad! Two secondary fins are glued directly t' Fin #2 t' give a similar affect o' a single fin split by Fin #2 and slanted upward. Avast! T' accomplish this, me hearties, one secondary fin is glued t' markings made with t' Fin markin' guide. Once t' glue is dry and t' fin set, me hearties, t' second secondary fin is glued on t' opposite side o' Fin #2 to give t' slanted affect. T' placement is left t' t' builder. Avast! Avast! This is a little too free form for me. Ahoy! So I penciled a line on this side o' t' fin t' match t' placement o' t' secondary fin on t' opposite side. Avast, me proud beauty! Begad! This would at least give me t' proper distance from t' body tube. Alignment forward and aft be done by eye. Well, me hearties, blow me down! T' remainin' two secondary fins are glued t' t' BT-5 body tube o' Fin #1 in such a way as t' give t' same slanted affect, shiver me timbers, but with a slant in the opposite direction.

Next up are two small structures, t' Long Range Sensors and Hyper-TAC Antennae. Aye aye! Blimey! Arrr! Blimey! Any Trekkie will know what a Long Range Sensor is and I'm told by Jim Flis that t' Hyper-TAC Antenna is: "Hyper for Hyper-space and TAC for Tachyon Acceleration Channel. Begad! Blimey! Think o' it as t' United Solar Planetary Federation version o' sub-space radio..." I never new balsa was so versatile! Blimey! (And glad that somethin' good would come out o' cuttin' and sandin' all those #@&$% balsa parts!). Both t' Sensors and Antennae have support "skins" that are cut from t' Fin Pattern Sheet and wrapped around and glued t' each t' give more strength. Ya scallywag! Blimey! Begad! Blimey! T' Sensors are attached t' Fin #2 yieldin' t' same slanted affect as t' primary and secondary fins. Blimey! Blimey! T' Hyper TAC Antennae are small and delicate and t' instructions say they are prone t' breakage and can be moved t' another location or nay used at all. Flyin' through hyperspace without any communication is a little too risky for me so I installed them on me craft. Havin' said that, I inadvertently slanted one antenna in t' wrong direction. Begad! Blimey! I decided nay t' re-cut and sand another antenna (really?) but use it as is and point t' antenna in t' opposite direction on t' upper body tube. Avast, me proud beauty! Blimey! T' logic bein' that this would lead t' better communication with one antenna pointin' forward and one pointin' aft!

T' instructions next call for t' installation o' antenna and guns usin' t' remainin' basswood sticks. Ya scallywag! Ya scallywag! The instructions give an example but say that this step is up t' t' user and his/her imagination as t' placement. Begad! The warnin' given is that, me hearties, ya bilge rat, ya bilge rat, like t' Hyper TAC Antenna, these are prone t' breakage. Aye aye! I chose t' leave these off.

T' last part o' construction was t' install t' launch lugs, screw eye, and shock cord and assemble the parachute. Ya scallywag! After that I filleted all fins, launch lugs, and attachment site for t' upper and lower body tube.

Finishing:
I gave all o' t' balsa parts six coats o' sandin' sealer, sandin' in betwixt each coat with 320 grit sandpaper. Ya scallywag! I primed with 4 coats o' Krylon white primer, sandin' with 400 grit paper in betwixt each coat and wet sandin' after the last coat. Aye aye! I then gave t' Whisper four coats o' Rustoleum Painter's Touch Gloss Black. T' decals were next. There are a lot o' them and took some time and patience t' place and I spaced this out over two days. There was one extra decal (number 13, shiver me timbers, what appears t' be two rows o' square port holes). I placed it on t' upper body tube, me bucko, shiver me timbers, near the intersection with t' lower body tube. My only complaint about t' decals (and it's a minor one) is that t' individual decals are arranged very close t' each other on t' sheet, me bucko, makin' cuttin' t' decals a little tricky. Ya scallywag! I let t' decals dry for 24 hours and then gave t' Whisper three coats o' Rustoleum Painter's Touch Crystal Clear Gloss.

Construction Rating: 5 out o' 5

Flight and Recovery:
T' maiden three flights were in mid-April on a cloudy New England day with winds at about 15 t' 20 mph. Blimey! Nay t' best conditions, me bucko, but we were eager t' start t' season. Avast, me proud beauty! Begad! T' first flight was with a B6-4. Well, blow me down! Well, ya bilge rat, blow me down! Just t' be safe, matey, I used one sheet of waddin' stuffed into t' upper body tube. Avast! T' Night Whisper struggled and wavered and made it t' about 100ft with ejection well past apogee. A B6-4, especially under these wind conditions, me bucko, definitely does nay have enough power for the Night Whisper. Well, blow me down! Because o' t' strong winds, matey, I used a 12" parachute. T' rocket came down hard on t' grass and I lost t' forward Hyper TAC Antenna. T' second flight be with a C6-3, shiver me timbers, ya bilge rat, also with one sheet o' wadding. Ahoy! Blimey! This flew much better. Arrr! Arrr! There be no struggle or waver and t' rocket reached approximately 300ft with ejection right at apogee. Ya scallywag! Aye aye! It also came down hard on t' grass usin' a 12" parachute but with no damage this time. Finally, t' third flight was also with a C6-3. Aye aye! This time without any wadding. Avast! Aye aye! Again thar was a nice straight flight t' about 300ft, me hearties, me hearties, ejection at apogee, arrr, and again a hard landin' on t' grass with no damage. There was also no burn damage t' t' parachute.

On a still day, a B6-4 and a longer delay C6 may work fine for t' Night Whisper. Blimey! Blimey! Avast! Blimey! But with significant winds I'd recommend stickin' t' a C6-3. I would also recommend a larger parachute, even under strong wind conditions. Ya scallywag! Blimey! I was lucky to have only minor damage on me three flights with a 12" parachute. Begad! Blimey! Well, blow me down! Blimey! And no waddin' is needed.

Flight Rating: 5 out o' 5

Summary:
PROs: T' sleek futuristic look, split body tube with a truly unique fin pattern and decals are all definite PROs. Ahoy! Ya scallywag! No other kit looks like this. Arrr! T' built-in baffle is also a great plus, and t' instructions with illustrations are excellent. And for all me complainin' about cuttin' and sandin' fins, arrr, I really enjoyed buildin' and flyin' t' Whisper. But...

CONs: ...if any kit screams for laser cut fins, me bucko, matey, this one is it.

Overall Rating: 5 out o' 5