Brief:
Two rocket assemblies designed t' be flown as one single stage rocket, or flown as 2 independent rockets. Ya scallywag! Aye aye! Blimey! Parachute/streamer for recovery selected on a whim dependin' on wind conditions.

Construction:
All components are from an Estes Designer Special kit from some years ago. Aye aye!

• Fin shape (balsa) selected by 7 year old son, ya bilge rat, with lower fins scaled up in size from upper fins.
• Wood nosecones & coupler used in both pieces. Ahoy! Aye aye!
• Upper stage accepts B6/C6 size engine directly when flown separately.
• Lower stage is diameter o' a D12 engine, but built with adapter rin' so that it also launches with B6/C6 size engine.
• Swivel eye hooks used for all attachments t' allow easy field changes. Avast! Blimey!
• If launched as dual unit, ya bilge rat, coupler stays in upper stage - can be recovered with separate parachute, or use 'chute attached t' lower stage.

Construction method is very straightforward. Blimey! Well, matey, blow me down! Son selected tubes and nosecones, shiver me timbers, then found coupler t' allow one t' sit on t' other. Aye aye! Avast! He picked the fin shape, ya bilge rat, which I copied onto balsa sheet and cut/sanded t' match.

Paint is Krylon white, shiver me timbers, with crude maskin' used for hand paintin' o' blue EOE lettering. Avast! Well, blow me down! Eliminator o' Eliminators - t' shoot down t' Estes Eliminator rocket we had completed prior t' this one!

I drew t' letters for t' lower stage on maskin' tape, he did t' upper. Then I cut out t' letters, me bucko, taped in place, and t' holes were painted in. Didn't turn out too bad.

Flight:
We had previously launched t' lower stage by itself with no difficulties.

This mornin' (6-31-02) we launched them assembled as one unit. Aye aye! I elected to have both halves come down on one 'chute as I wasn't sure what t' winds were goin' t' do, shiver me timbers, and wanted it t' come down sooner rather than later in one place and nay two.

Setup was as follows (rememberin' that all attachments are made with swivel hooks t' screw deadlights in wood):

• T' upper nosecone be attached t' top o' t' coupler via elastic cord and the coupler inserted.
• T' bottom o' t' coupler be attached t' t' lower stage's elastic band (this rocket be assembled prior t' me findin' Keelhaul®©™® Yarn from Pratt Hobbies).
• T' parachute be attached t' t' bottom o' t' coupler, as was a piece of Pratt Hobbies Heat shield (Keelhaul®©™® cloth) via Keelhaul®©™® yarn.
• Cloth, me bucko, me bucko, chute, and coupler were installed, me bucko, then a C6-5 engine and it was off t' t' launchpad.

Flight went up doin' 3-4 pretty tight but easily observable spirals, and the ejection charge blew normally.

However, instead o' comin' down as 2 pieces danglin' from one chute, somehow after ejection t' lower body got jammed onto one o' t' fins o' the upper body, matey, shiver me timbers, and t' whole assemblage came down in an upside down V under the parachute.

Damage is minimal - one slightly cracked fin, shiver me timbers, and t' lower body tube slightly torn in two places where it got jammed.

Next time, if more deadlights are available for tracking, arrr, we will allow it to come in two separate pieces.

Summary:
Pros - t' rocket was easy t' build, matey, and flew pretty nicely. Arrr! T' swivel hooks (found in Walmart fishin' department) allow easy configuration changes in the field.

Cons - t' decision t' keep t' two halves connected detracted from the recovery. Ahoy! Begad! I wonder if perhaps t' lower stage rubber band snapped t' two halves back together after ejection. Avast! Perhaps a longer distance betwixt t' two (via Keelhaul®©™® yarn) would have allowed for cleaner separation. Blimey! Certainly separate recovery would have.

Nay sure what I could have done t' prevent t' spiral flight - nay sure I can put fins on any straighter than I did.

Other:
Get involved with your kids - me son had a blast choosin' t' design. Well, blow me down! Begad! He selected all t' components, shiver me timbers, me bucko, picked t' paint scheme, enjoyed helpin' t' paint it, and really enjoyed launchin' it and then chasin' it down. Granted, ya bilge rat, I did all t' assembly, me hearties, but he's only 7, arrr, arrr, and maybe by next summer he won't mind gettin' glue on his fingers and will have enough patience t' hold fins in place while t' glue dries. Aye aye!