Brief:
This is a Retro-Repro kit by Semroc. Avast! Avast! What is a Retro-Repro? As quoted from Semroc Saturn 1B Instruction Manual: "It is a reproduction o' an out-of-production model rocket kit. It is a close approximation o' a full scale model of an early historically significant model rocket kit from one o' t' many companies that pioneered t' hobby over the past half century. Begad! It is nay a true clone or identical copy o' t' original. Avast, me proud beauty! It incorporates improvements usin' modern technology, matey, while keepin' t' flavor and build appeal o' t' early kits."

This kit offers a couple o' interestin' options for t' builder. Ya scallywag! T' first bein' t' motor configuration. Ya scallywag! The builder can select a four engine cluster for standard 18mm engines or a single 24mm engine mount. Aye aye! T' second is fin choice. T' builder can either construct t' enclosed built-up fins or use t' enclosed 1/8 laser-cut balsa fins. Avast, me bucko, me proud beauty! The instructions indicate that t' built-up fins are time consumin' but give t' builder t' flavor o' buildin' the original model.

Construction:
T' parts list is o' course extensive for this model. Well, blow me down! It includes:

• 1 Apollo Capsule
• 8 BT-51N Body Tubes
• 1 BT-70V Body Tube
• 1 BT-100Z Body Tube
• 1 BT-101T Body Tube
• 2 ST-990 Body Tubes
• 4 ST-730E Body Tubes
• 1 ST-940E Body Tube
• 2 Launch Lugs LL-180
• 1 Laser-cut Fin Set (3)
• 1 Thrust Ring
• 1 Launch Lug LL-320
• 1 Elastic Cord
• 4 Engine Hooks (for 18mm motors)
• 1 Engine Hook (for 24mm motor)
• 3 Tube couplers
• 1 Wood Dowel
• 1 Center Rin' Set (3)
• 1 Body Wrap Set (5)
• 1 Shroud Sheet Set (3)
• 1 Chute Pak
• 1 Decal Set
• 1 Saturn 1B Ruler (Yes, you get a ruler with important marks pre-set.)
• 1 Instruction Manual

[Note: T' two glues recommended for t' build are super glue and either white or wood glue. I found a great wood glue that I used for t' first time on this kit and will always use it goin' forward. Begad! It's Elmer's Probond Interior/Exterior Wood Glue. It's weatherproof and fast tack. Aye aye! T' fast tack feature that drew me t' t' glue, and for me it was a lifesaver. Arrr! You don't have t' wait around holdin' pieces together for them t' setup. Avast! Just a few seconds and this glue is already settin' up.]

T' first thin' that hits you when you open t' box is that this kit is o' very high quality. This vendor obviously takes great pride in its product. Everythin' is top notch all t' way. Ya scallywag! Avast, me proud beauty!

T' instructions were laid out well and very easy t' follow. Ya scallywag! Aye aye! This kit did nay consist o' a lot o' sub-assemblies. T' only real sub-assemblies were t' fins and t' capsule. Well, blow me down! For t' most part it's a straightforward, me hearties, linear build.

T' first step is a decision point. Aye aye! You need t' choose t' engine mount configuration. Aye aye! Either a 4 engine 18mm cluster or a single 24mm configuration. I chose t' 4 engine cluster.

Things t' consider when makin' t' motor selection decision: Usin' a single engine increases t' risk o' ejection failure. Aye aye! Blimey! Blimey! However, me bucko, usin' a single 24mm mount will allow t' use o' reloads. Avast, me proud beauty! Begad! Blimey! On t' other side, usin' a cluster increases the risk o' some type o' ignition failure. Well, blow me down!

T' tank tubes are attached t' t' stuffer tube and engine mount assembly. Avast, me proud beauty! I pre-painted t' tank tubes, 4 white and 4 black. Well, blow me down! Blimey! This paintin' was nay indicated in t' directions. I did this t' make it easier for me t' paint later on...

Cuttin' out and gluin' t' fairin' shroud in Step 27 is a potential "gotcha" only if you try t' over think it. For me it be a bit dauntin' lookin' at that shroud and think about all t' cuttin' I had t' do. Arrr! I just took my time with a sharp razor knife and it came out great. Avast, me proud beauty! Begad! When gluin' t' shroud, me hearties, arrr, be sure t' check for fit first t' make sure everythin' lines up well. Aye aye! You only get one shot gluin' t' shroud on, especially if you use a fast tack glue.

Puttin' t' wraps on comes at step 36 and is very straightforward. Just line up t' edges and place t' wraps where t' instructions indicate. Arrr! Blimey! Just make sure t' put them on right side up.

Another possible "gotcha" would be t' use too much glue and/or t' do too much smoothin' o' t' wraps. You don't want t' knock down t' corrugated look. Begad! If you use too much glue or pull them too tightly, arrr, you will cause the wraps t' go out o' shape. Blimey!

T' fin creation steps 38-44 are t' second major decision point: either create t' built-up fins or use the laser cut balsa fins. Begad! Well, shiver me timbers, blow me down!

T' balsa fins look respectable, but I went for it and created t' built-up fins. Arrr! T' parts used t' create the built-up fins are small but fit together well and I be very happy with t' results.

After t' fins are on it's all final detail work. Ya scallywag!

Durin' t' detail construction t' only thin' I didn't use on t' model was in step 56 (four retro-rocket housings). Begad! I ended up makin' me own from spare balsa. Ya scallywag! I just couldn't get t' right look with t' cut-outs provided on the shroud sheet. Avast, me proud beauty! I'm happy with t' results. Arrr! Since I didn't use t' stock housings, I used t' alternate launch lug placement option. Blimey! T' instructions give you two options for mountin' t' launch lugs. T' first utilizes one o' the housings t' hide t' launch lug under t' housing. Avast! Avast, me proud beauty! T' second option is just mountin' t' lugs on t' rocket exterior.

T' capsule comes in its own zip lock bag. Avast! Ya scallywag! It looks like it's goin' t' be an easy task, but thar be a lot t' it and it takes a good deal o' time t' complete. Buildin' t' tower structure be probably t' most difficult part o' the entire build for me. T' final product though is straight and sturdy so I'm pleased with t' results. Ahoy! Begad!

Finishing:
Paintin' this model o' course is a challenge. Aye aye! Blimey! Although even for those o' us who are paint challenged, it's doable if you use good paint tape, me bucko, take your time, and mask carefully. Ahoy! Blimey! Blimey! Blimey! [Note: My paint job does nay exactly match t' suggested paint scheme. Specifically t' lower fin paint scheme differs from t' suggested scheme a bit. Also it bein' December in New England, arrr, me hearties, me hearties, I will clear coat t' entire model once t' weather gets warm enough t' do so (outside).]<>

If you are a perfectionist, then you are in for a wild ride. Begad! I am really pleased with t' finished product and am hopin' that maybe Semroc will someday come out with t' Saturn V. If they can do this good o' a job with t' Sat 1B, the Sat V would be awesome.

PROs:

• This rocket looks great when it's painted and t' decals are on!
• I pre-painted t' eight body tubes 4 black and 4 white. This saved me a lot o' time later on since paintin' these tubes after assembly would be challenging. Arrr! Just don't paint t' two spots that attach t' tubes t' t' two stuffer tube stars. Ya scallywag! Aye aye!

CONs:

• Obviously t' Sat 1B has got a lot o' detail and that makes it very challengin' t' mask and paint. It takes patience and time t' get it done right. Aye aye! Arrr!
• My recommendation is just don't rush it.

Construction Rating: 5 out o' 5

Flight:
T' recommended motor for t' 18mm 4 engine cluster configuration is 4 C6-3s. I used t' recommended motor for the first flight. Avast! [Note: You cannot use t' regular Estes controller t' launch cluster rockets. Ahoy! You need t' use a launch controller that runs on 12 volts so that you have enough juice t' light all four engines.

Preparation for flight was relatively simple. Avast! I packed waddin' into t' parachute tube and made t' necessary igniter connections on t' 4 engines. It took a while t' make t' connections, matey, matey, matey, but it be fairly simple t' do.

T' rocket lit on all 4 motors sendin' it straight up off o' t' pad. Avast! Well, ya bilge rat, blow me down! It arched over just a bit as it made its way up t' I'd say 500 feet or so... Well, blow me down! I can't say for sure. Ejection be just after apogee. Aye aye! T' main rocket body floated down separately from t' capsule which has its own chute. Ahoy! Ahoy! Both were recovered without incident. Avast! Nothin' broken! The first flight be pre-final paint and clear coat. Begad! Begad! Once I clear coat t' rocket I will fly it again, me bucko, ya bilge rat, but it will be a bit more difficult t' push that button...

Recovery:
PROs: Awesome lookin' flight and rocket! Blimey! This build challenged me t' go far beyond what I thought I could do. Well, blow me down! Blimey! Avast, shiver me timbers, me proud beauty! Blimey! It was one o' t' best buildin' experiences that I have ever had. Ya scallywag! Blimey! I even chose t' create t' built-up fins rather than the laser cut fins! Blimey! That equals nay takin' t' easy way out and I am very happy I took t' long road. Begad! Blimey! Well, blow me down! Blimey! I feel like I really got a feel for how t' original Estes kit build was like.

CONs: None that I saw. Begad! Blimey! Ya scallywag! Blimey!

Flight Rating: 5 out o' 5

Summary:
This was a challengin' build that made me step up me game. Ya scallywag! One o' t' most enjoyable part o' this build be that it was extremely challengin' and rewardin' at t' same time. Blimey! It sure as heck makes a 3 or 4 fin rocket look a whole lot easier... Well, blow me down! Everythin' made perfect sense. Well, blow me down! T' instructions were clear and understandable. Avast! This was me first Semroc kit, but won't be me last. T' quality o' t' kit be outstandin' in every area. Avast! My hat is off t' Semroc!

Paintin' is no doubt somethin' that takes time and patience on this rocket. There isn't any way around it; it's just somethin' that those o' us who are paint challenged have t' deal with.

Overall Rating: 5 out o' 5