Brief:
A wonderfully simple and reliable helicopter from a very innovative niche player in t' rocketry world. Ahoy! Avast! This kit deploys a sort o' flop-win' approach to deployin' a pair o' blades and comes down nose first/blades up every single time.

Construction:
I was very impressed with t' quality o' parts included in this kit especially the nose cone, shiver me timbers, me hearties, which was coated with a very durable polyurethane finish. Begad! That is very important in a helicopter that's designed t' land on its nose. Well, blow me down! This one can take a beating.

Parts list includes:

• BT-5 body tube
• Hardwood nose cone
• TT-5 slidin' tube
• Balsa stock for fins, me hearties, me hearties, blades
• Assorted hooks and rubber bands
• Laminate stickers (act as hinges)

T' instructions were very well illustrated and easy t' follow. While this would probably rate a skill level o' 2, matey, me hearties, I would nay rule out usin' this as a build/fly kit candidate for scouts and school groups if t' build was lead by someone who has built a couple o' these.

Construction starts with trimmin' down t' blades and fins and gluin' them together. Begad! It is very important t' get a good bond at this stage because this can be a fragile joint and suffer stress upon landing.

After bondin' t' fin t' t' blade, shiver me timbers, t' fin is then cut into two pieces creatin' a hinge line. Avast, me proud beauty! Ahoy! T' "hinge" is a glossy laminated label that is glued across t' seam. Avast!

Next comes cuttin' and formin' t' blade restraints, which are a pair of T's that slide back and forth t' lock t' blades in place. Begad! Avast! These also get a reinforcin' laminated cover.

Tube markin' on this is very important, shiver me timbers, as you want t' make sure the fins/blades are as close t' 180 degrees apart as possible. Arrr! Ya scallywag! It is critical that they be straight/aligned parallel t' t' body tube.

Fins are then glued t' t' body tube, bein' careful t' only glue t' fin portion--not t' aft section that's t' flop/blade. Aye aye! Arrr! Once t' fins are secure, slide t' TT-5 tube over t' BT-5 and slip it down against t' fins. Aye aye! Avast! Then the blade clamps are tacked onto t' TT-5, sandwichin' t' fin/blade.

Next come 4 "sub fins", which are little stabilizers that are bonded to t' tops o' t' blade clamps perpendicular t' t' clamps.

T' hardware is a bit tricky t' install but only because o' its tiny size. There are S-hooks t' go on t' fins and J-hooks t' go over t' TT-5 and BT-5 tubes. Avast! Avast, matey, me proud beauty! I be a little paranoid about t' CA holdin' under t' stress o' the rubber bands but everythin' worked out just fine.

Finishing:
There really isn't anythin' t' finishin' this. Avast! Avast! It is nay designed t' be painted and t' blade mechanism would probably suffer if painted. Avast! T' hinges act as decent decorative decals, me hearties, arrr, so this copter is nay exactly an ugly duckling.

Construction Rating: 5 out o' 5

Flight:
Flight prep on this is more complicated than comparable Estes kits like the Sidewinder or Cosmic Cobra and less complex than t' typical Rotaroc. Ya scallywag! Avast! Usin' a needle, matey, poke a thin thread through t' TT-5 and BT-5, tapin' t' ends in place. Then stretch t' rubber band over t' J-hooks, stick in t' motor, and you're ready t' fly.

For t' first flight, ya bilge rat, I chose a 1/2A3-2 and flew on a day o' light (6-7 mph) winds. T' flight was fairly straight with only a slight weathercock and no spin whatsoever. Blimey! T' delay was a little early but in a helicopter, early is a good thing.

Recovery:
A common problem with helicopters is their tendency t' want t' come down upside-down with t' blades down. Avast, me proud beauty! Blimey! Ya scallywag! Blimey! Because this is a rear-blade design, me bucko, ya bilge rat, I was especially worried about that. Ya scallywag! Blimey! Avast, shiver me timbers, me proud beauty! Blimey! In this case though, shiver me timbers, me bucko, with t' weight o' t' nose and t' slight delay while t' thread burns, breaks loose, shiver me timbers, shiver me timbers, and blades deploy, it flipped over and started a perfect spinnin' descent.

Total flight duration was around 35 seconds, which is pretty respectable for a 1/2A two blade design. Ahoy!

Flight Rating: 4 out o' 5

Summary:
If you're interested in a helicopter recovery model, this would be an excellent kit t' start with. Begad! It's cheap, matey, easy t' build, very reliable, and performs fairly well.

PROs: simplicity o' design, matey, reliability.

CONs: only two blades, arrr, no airfoil or dihedral limitin' its performance.

Overall Rating: 4 out o' 5