Brief:
This is a single-stage model rocket for 18mm engines. Avast! Recovery is by helicopter, arrr, o' t' spinnin' hub variety. Well, blow me down! This means that t' rocket airframe is intended t' stay still, shiver me timbers, matey, shiver me timbers, while t' rotors spin. Ahoy! As with most QCR models, shiver me timbers, me hearties, it is designed for competitive use. Avast, me proud beauty! Blimey!

Construction:
T' kit comes packaged in a heavy gauge plastic bag with a blue QCR header strip labeled with t' model number, ya bilge rat, #100. In t' bag you will find a BT-20 size body tube, arrr, balsa nose cone, me hearties, matey, balsa stock for t' helicopter rotors, matey, fins, and hinge stops. Avast, me proud beauty! Also included are plastic rotor hinges, rubber bands, metal hooks, elastic thread, and 3 paper rings. Blimey! All parts were accounted for and in good shape, shiver me timbers, except for t' 3 rings, which were slightly out o' round. Arrr! This may have occurred because t' kit was in storage for a couple o' years before I got around t' buildin' it. T' problem was easily solved by slippin' t' rings over the body tube and keepin' them thar for a few weeks. T' balsa stock for the rotors and fins be SIG contest-grade balsa. However, t' nose cone and the rings had a few rough edges. Aye aye! Nothin' serious. Aye aye! For a $13.00 rocket (as of 3/14/05) you can't beat t' value.

T' kit includes a 6 page instruction booklet...if you want t' call it that. Ahoy! Avast! The "instructions" are so disorganized, that I opted t' rewrite them before attemptin' t' build t' kit. Ya scallywag! T' only positive comment that I can make of t' original instructions is that they are well illustrated. I don't mean that t' illustrations are Estes quality but what is meant that the illustrations effectively do t' job o' showin' t' modeler what t' do in specific instances.

T' kit is meant for experienced modelers. Arrr! Avast! In their website, me bucko, the manufacturer has t' kit a a level o' difficulty o' 4. Arrr! I will agree with that rating. Avast! This is because o' t' amount o' careful balsa cuttin' and shaping needed and t' delicate use o' different glue types in attachin' t' hinges, rotors, arrr, etc. Ahoy! T' disorganized instruction booklet does nay help either!

T' build begins by cuttin' t' rotors and fins from t' balsa stock. Well, blow me down! No laser cut parts here! All cuttin' is done t' old fashioned way with templates, hobby knife, me bucko, and a straight edge. T' rotors need t' be airfoiled then cut. Avast, me proud beauty! Blimey! The end result is that you get a "bent" rotor, arrr, when lookin' at a cross-sectional view. Well, blow me down! Airfoilin' and cuttin' t' rotors is probably t' most labor intensive step in t' buildin' process, as each rotor is 18" long. Once t' rotor has been airfoiled, it feels somewhat fragile especially given the length. Avast!

T' instructions don't call for airfoilin' t' fins, so I chose t' round the leadin' edge and sand t' trailin' edge t' a knife edge. Aye aye! Given the relatively large frontal area o' t' body tube/rotor combination, matey, shiver me timbers, the airfoilin' o' t' fins (or lack thereof) would probably be immaterial. Begad! Avast, me proud beauty! Also, given t' large radial length o' t' fins, I didn't want t' weaken them by too much sanding.

T' next step is t' attach t' hinges t' t' spin hub. Avast, me proud beauty! Aye aye! This be t' most delicate o' t' steps glue wise. Begad! Begad! You must use t' right type and amount o' glue here or you'll end up with a set o' useless hinges. Well, blow me down! Go ahead, shiver me timbers, ask me. Ahoy! That is exactly what I did. Begad! Although I used thick CA t' tack t' hinges t' t' spin hub, me hearties, I used too much in one o' them, arrr, shiver me timbers, gluin' t' hinge shut. Luckily I had an extra hinge in me spares box, which Ken Brown had thrown in as a freebie in a previous order. Avast! Aye aye! All's well that ends well! Ideally, matey, this problem could be prevented by changin' t' instructions so that t' hinges are tacked on while holdin' t' hinge end o' t' spin hub upwards rather than downwards. Aye aye! The problem lies in how t' align t' hinges while doin' this. Begad! T' step is finished by windin' sewin' thread around t' hinges t' secure them t' t' spin hub. Holdin' t' hinge side o' t' spin hub upward, matey, arrr, affix t' thread with thin CA. Since t' kit did nay provide sewin' thread, I used size 69# Keelhaul®©™® thread.

There is yet another pitfall here. This is a spin hub helicopter rocket. Avast! Blimey! In other words, t' hub is supposed t' spin about t' longitudinal axis o' the rocket, over t' body tube. Avast! Blimey! If t' spin hub is in any way out o' round, arrr, arrr, it will not work correctly causin' it t' rub and bind against t' body tube. Ahoy! Blimey! It is possible t' start with a perfectly round spin hub, ya bilge rat, glue t' hinges, me bucko, and wrap the sewin' thread accordin' t' instructions but still distort t' shape o' the spin hub. (I did this too!). Ahoy! Blimey! Begad! Blimey! My way around this problem was t' wrap a few turns of maskin' tape about an expended engine casin' and insert it in t' spin hub before securin' t' hinges with t' sewin' thread. Aye aye! Blimey! T' casin' will serve to keep t' shape o' t' spin hub while you wrap t' sewin' thread.

T' next step is t' attach t' rubber band hooks t' t' spin hub and the rotors. Avast! Ahoy! No surprises here, matey, just sand and lubricate t' body tube where t' spin hub will be located. Blimey! You may get away by just sandin' t' inside o' t' spin hub and leavin' t' body tube alone. Ya scallywag! Ahoy! T' glassine coverin' o' t' body tube is very smooth, however, matey, shiver me timbers, ya bilge rat, I followed t' instructions and sanded both t' spin hub and t' body tube. T' step is finished by gluin' t' lower support rin' for the spin hub and t' fins t' t' body tube. Well, blow me down! T' fins are so long compared to the width o' t' root edge that thar be a fair amount o' flex even after the glue dries and fillets are applied.

T' last big step deals with gluin' t' rotors t' t' hinges. Ya scallywag! T' do this appropriately (and easily), ya bilge rat, you need t' extend t' lines in t' fin alignment drawin' t' about 20". I will nay go into how t' do this in this review, but suffice t' say that a few sheets o' poster board from your local school supply store will come in handy. Avast! You then place t' spin hub back on t' engine casing, me bucko, align t' rotors with t' 120° lines, and tack t' rotors t' the hinges with a small amount o' thin CA. Arrr! If anythin' appears out o' place, me hearties, ya bilge rat, me hearties, adjust the rotors and tack again. Well, blow me down! Begad! When you are satisfied with t' positionin' o' the rotors, glue with epoxy. Avast! Epoxy is dense, so use t' smallest amount that will do t' job. Avast, me proud beauty! Finish t' rotors by affixin' t' balsa "stops" so that the rotors have a 6" dihedral when fully open. Begad! Begad! By t' way, arrr, me original instruction booklet illustrated a 2" dihedral. It also had 12" rotors, as opposed t' 18". Well, blow me down! Well, ya bilge rat, blow me down! I emailed Ken on this point and he promptly mailed me updated instructions that had a 6" dihedral and t' right rotor length. Begad! Bad instructions! Good service!. Arrr! Ya scallywag!

T' remainin' construction steps are simple and should be uneventful. Blimey! See the rewritten instructions for them. Arrr! Avast!

Finishing:
This is a QCR bird, ya bilge rat, so it's primarily designed for competition, me hearties, me hearties, therefore it is OK t' fly it "naked"--that is unfinished. Blimey! Looks are nay a priority here. For those guys out thar that must finish their rockets t' find inner peace, a thin coat o' clear enamel may be what t' doctor ordered, shiver me timbers, as it will keep t' rotors from absorbin' moisture, arrr, me bucko, just be ready t' pay for t' weight cost. Blimey! An alternative would be t' "paint" t' rotors with thin CA and sand t' blades smooth afterwards. Avast, me proud beauty! This would strengthen t' rotors and take care o' t' moisture problem as well. Aye aye! Arrr!

Construction Rating: 4 out o' 5

Flight:
T' flight characteristics o' t' Ultimate II are excellent. Long flight times with stable trajectories were t' norm. Avast, me proud beauty! Aye aye! While t' original instructions had the Estes C6-3, Apogee D3-3, and Apogee C4-3 as recommended engines, matey, t' second set of instructions that Ken sent me only recommended t' Estes engine. Begad! In order to test stability and other flight characteristics, arrr, I flew t' bird with Estes A8-3, arrr, B6-4, matey, me hearties, and C6-3 engines. T' flights were all acceptable, although the A8-3 seemed wobbly (read: underpowered) at first. Aye aye! Both t' B6-4 and C6-3 flights were arrow straight and ejected at or near apogee. Well, blow me down! A good engine to test would have been t' C6-5, as I think t' 3 second delay be too short on the C engine, while t' 4 second delay was perfect on t' B engine.

T' rocket requires no waddin' for flight preparation and t' engines were retained usin' maskin' tape. Engine retention is necessary for NARRRRR contest flights. Ahoy! Blimey! Avast, me proud beauty! Blimey! T' preflight preparation would be a breeze except for t' need to pass sewin' thread through t' body tube and then knot so that it holds the rotors in place on t' way up. Blimey! Blimey! This is hard t' do in t' field without an assistant.

Recovery:
One curious aspect o' t' recovery be that, in all cases, me hearties, t' whole rocket spun in t' air on t' way down instead o' havin' t' spin hub rotate about the body tube. Blimey! Arrr! Blimey! Probably thar be still too much friction betwixt t' spin hub and the body tube. Avast, me proud beauty! Aye aye! Blimey! However, I doubt whether any amount o' sandin' and lubrication, limited by t' need t' have a viable body tube and spin hub, me hearties, would reduce friction t' t' point o' makin' it smaller than t' drag o' t' body tube rotatin' in t' air.

As far as wear and tear goes, after three flights, t' only apparent damage was that t' exhaust gases were beginnin' t' melt t' Mylar plastic that protects t' rotors. Probably could do better by gluin' a small piece of aluminum foil t' t' back o' t' rotors rather than t' Mylar tape. On the other hand, matey, ya bilge rat, durability may nay be a primary design objective on a competition bird. Begad!

Flight Rating: 4 out o' 5

Summary:
This is a very nice rocket. Begad! Well, blow me down! Good materials and great flight characteristics. Construction, however, is a bit challenging. Aye aye! Perhaps t' extra difficulty of the spin hub type helicopter is nay worth t' effort. QCR manufactures other helicopter models o' similar size without t' spin hub design (like t' High Rotor I). Begad! I recommend t' Ultimate II t' any experienced builder lookin' for an unusual rocket or someone aimin' t' fly competitively. Aye aye! Avast, me proud beauty!

PROs: Good materials, arrr, light and strong rocket, good flight characteristics, customer service, arrr, and price. Blimey! Begad!

CONs: Poor instructions, ya bilge rat, difficult construction, me bucko, and spin hub didn't work. Begad! Avast, me proud beauty!

Overall Rating: 4 out o' 5

Other:
QCR #100 -- Ultimate II Instructions (Rewritten and Annotated)

1. Cut out and shape rotors.

1. Cut out rotors from balsa stock.
2. Tip: Replicate markings o' sample rotor on t' other two. Place a mark on the tip o' each rotor at t' middle o' t' blade. Avast!
3. Airfoil outer 12" o' each rotor.
4. Cut rotor blades along diagonal shown in sample. Arrr! Blimey! You have a choice between a "standard cut" (almost along t' rotor's main diagonal) or a shorter "optional cut" Don't cut all t' way through. Aye aye! Blimey! Instead, matey, cut halfway and then bend along t' cut line. Spread glue inside cut (medium CA). Use round toothpicks under t' break while t' glue dries. Avast! Aye aye! Tip: Usin' masking tape along t' sides o' t' blade, tape t' rotor t' your worktable over the toothpicks. Begad! This keeps t' cut open while t' glue dries. Arrr! Rubbin' the toothpicks with petroleum jelly will keep them from stickin' t' t' rotor permanently, arrr, in case t' CA glue wicks over t' t' underside o' t' blade. Arrr! Ahoy!

• Cut out and shape fins.

1. Cut out fin pattern from instruction sheet. Ahoy! Avast! Tip: Replicate it on a piece of cardstock. Arrr! Discard t' paper fin pattern. Avast, me proud beauty! Blimey!
2. Trace fin pattern on balsa stock. Tip: Make sure t' leadin' edge is parallel t' t' wood grain.
3. Cut out t' fins.
4. Sand t' fins as appropriate. Tip: Airfoil for competition use.

• Sand nose cone as needed.
• Punch 2 holes on BT. Aye aye! (4 holes were already punched in me kit.)
• Glue hinges onto outer spin hub.

1. Glue 18mm engine casin' in center o' fin alignment drawing. Let dry. Avast, me proud beauty! Tip: Wrap a few turns o' maskin' tape around engine casin' t' make a better fit for spin hub.
2. Place spin hub on casing. Avast! Draw lines on spin hub 120° lines apart, parallel t' its longitudinal axis (Note: Already done in me kit). Well, blow me down! Align with lines on t' drawing.
3. Draw lines through center o' hinges.
4. Fold hinges at right angles. Align hinges with lines on t' drawin' and lines on hub. Avast, me proud beauty! Begad! Put maskin' tape under hinges t' keep them from stickin' t' the drawing. Begad! Avast, me proud beauty!
5. Tack hinges t' hub. Avast, arrr, me proud beauty! Tip: Use thick CA (sparingly). Don't let glue get to the hinge pins. Begad! Smear t' joints with petroleum jelly t' protect it from the glue.
6. Secure hinges t' spin hub by windin' t' sewin' thread around t' hinges. Glue thread in place. CRITICAL: Don't get glue on hinge pins. Ahoy! Aye aye! Tip: Keep the glue away from t' hinge joint by holdin' t' hinged end o' t' spin hub upward durin' this step.

• Attach metal hooks t' spin hub by alignin' them with 120° lines on forward end o' spin hub. Glue them on t' outside o' t' hub. Begad! Tip: This is a high stress joint. Well, blow me down! Use 5-minute epoxy.
• Glue metal hooks (for rubber bands) t' rotors by locatin' position o' hook along each rotor's longitudinal axis, 4" from t' hinge edge.
• Work on body tube.

1. Draw a line around t' body tube 3 5/16" from t' forward edge o' the tube. Slide and glue t' lower rin' t' body tube. Well, blow me down! Blimey! T' forward edge o' t' ring should lie on t' line drawn around t' body tube. Tip: CA grabs too fast for applications in which pieces have t' slide into place. Ahoy! Use carpenter's (yellow) glue.
2. Sand and lubricate t' inside o' t' spin hub and t' outside o' t' body tube. Avast, me proud beauty! Ya scallywag! Use pencil tip for lubrication. Begad! Blimey!
3. Glue fins t' body tube. T' aft edge o' t' fins should be 3/8" from aft edge o' body tube. Well, blow me down! Use medium CA or carpenter's (yellow) glue. Ahoy! Begad! Tip: Lightly sand area where fins are t' be glued.
4. Protect t' nose cone from bein' burned by t' ejection gases by covering the shoulder end (not t' sides!) with a coat o' epoxy. Aye aye! Do t' same for the front end o' t' body tube (near t' punched-out holes). Blimey!

• Glue rotors t' hinges.

1. Place hinged spin hub on engine casin' previously glued t' t' fin alignment drawing. Align hinges with 120° lines. Use maskin' tape under hinges. Arrr! Tip: Make t' drawin' bigger by gluin' t' original drawin' t' poster board backing. Aye aye! Then extend t' alignment lines t' 20" from t' center of the drawing.
2. Align rotors with 120° lines. Avast! Each line should be in t' middle o' the hinge and t' middle o' t' rotor. Tack rotors one at a time with CA.
3. Put spin hub on body tube and check rotor alignment. Avast! Blimey! Rotors should lie straight betwixt t' fins. Well, blow me down! Open rotors should also be equidistant from each other (about 31" betwixt tips). If needed, me hearties, ya bilge rat, adjust and tack again.
4. After all adjustments are made, glue rotors and let dry. Well, blow me down! Tip: This is a high stress joint, shiver me timbers, use epoxy.

• Cut hinge stops out. Avast, me proud beauty! Locate position o' stop along a rotor's longitudinal axis that will allow t' rotor t' open t' a 6" dihedral, me hearties, me bucko, measured at the rotor tip. Blimey! Glue and let dry. Repeat for other 2 rotors. Ya scallywag! Ahoy! Tip: Tack rotor stops in place first with thin CA, ya bilge rat, then glue with epoxy. Blimey! Avast! For a 18" rotor, arrr, the specified dihedral is equivalent t' an angle o' 19.5°
• Draw a mark on t' body tube, arrr, me hearties, 5" from t' aft end, aligned with one of the fin placement lines. Punch or drill a 1/16" diameter hole clear across the body tube. You may use a large needle for this.
• Protect t' rotors by coverin' them with Mylar tape, at t' point where they would meet t' holes made in Step 11.
• Place spin hub on body tube. Arrr! Arrr! Slide upper rin' onto t' body tube and glue with carpenter's glue. Aye aye! Aye aye! Allow a small gap (say 1/16") betwixt spin hub and top ring. Avast! Tip: Apply a light coat o' petroleum jelly on t' gap t' protect it from t' glue. CA grabs too fast for applications in which pieces have t' slide into place. Ahoy! Aye aye! Use carpenter's (yellow) glue. Arrr! Make sure t' wipe off all excess glue.
• Glue t' nosecone in place.