Brief:
This is a 3x18mm cluster, vectored-thrust, matey, ya bilge rat, ya bilge rat, single stage.

Construction:
Parts List:

• 1 BT-55 (18")
• 1 BT-60 (18")
• 3 BT-20 (2.75")
• 1 Balsa nose cone (5 3/8" straight cone)
• 1 Balsa transition (1")
• 3 Sheets balsa fin stock (1/8")
• 1 Sheet balsa fin stock (1/16")
• 1 Custom laser-cut centerin' ring
• 1 Wide shock cord
• 1 Plastic 16" parachute kit (unassembled)
• 1 Screw eye (medium)
• 2 Launch Lugs (3/16")
• 3 18mm engine blocks
• 1 Fin Pattern Sheet
• Assembly instructions, includin' hints and tips for clustering

All parts were included and arrived in very good condition. Ya scallywag!

T' instructions were extremely easy t' follow, shiver me timbers, and were very extensive. Pictures were provided for every step o' construction, with multiple images within each figure for more complicated steps.

T' motor mount assembly be clearly presented, which was essential for such an unorthodox mountin' configuration. Blimey! T' motor mount assembly was actually quite simple, me bucko, shiver me timbers, and produced a surprisingly strong structure.

T' main body tube be prepared by usin' t' fin markin' guide, me bucko, me bucko, matey, which included cut-out areas for t' motor mount tubes. Blimey! Blimey! Ya scallywag! Blimey! T' notches for t' motor tubes are cut out, and t' motor mount assembly slides up into t' notches. Well, blow me down! Blimey! The instructions direct t' builder t' sand t' notches with a piece o' sandpaper wrapped around a spent motor casin' until t' assembly fits snugly into t' end of t' body tube with t' centerin' rin' flush with t' tube end. I had t' sand off an additional 3/16" before I be able t' get t' mount t' fit properly, matey, but once it did, gluin' was easy and t' mount fit perfectly.

Each o' t' fins consists o' a main fin and a strake. Arrr! T' instructions again are very clear about how t' ensure that t' wood grain is properly aligned for maximum strength. Begad! Well, shiver me timbers, blow me down! Blimey! Because t' forward edges o' t' main fins are angled, me bucko, the trailin' edge o' t' strake must make an equal angle, which may prove difficult if t' angle had been altered slightly durin' t' sandin' process. Avast! Blimey! Once t' two wood pieces are matched, ya bilge rat, they join easily. T' main fins are attached first, and then t' strakes are attached along t' guide lines drawn earlier with the fin markin' guide.

All parts are extremely well made, arrr, matey, and fit together very well. Avast! Ya scallywag!

Pros:
Very thorough instructions
Strong airframe

Cons:
Engine mount notches nay cut deep enough
Fin/Strake alignment may prove problematic

Finishing:
No special requirements or techniques are mentioned for t' finishin' o' this kit. For those who desire t' replicate t' images on t' cover o' the packaging, me bucko, a maskin' template is provided for t' numeral "3". Arrr! Begad! No decals are provided.

Construction Rating: 4 out o' 5

Flight:
T' kit packagin' recommends either B6-4's or C6-5's, shiver me timbers, shiver me timbers, as long as you use 3 of the same kind. Aye aye! Begad!

I launched mine on C6-5's, shiver me timbers, me hearties, me hearties, and for t' first two flights, only two o' the three motors ignited, matey, me hearties, due t' a faulty clip-whip. Ahoy! Blimey! Despite t' loss o' thrust, the rocket still flew beautifully and t' ejection was well timed. Once I was able t' get all 3 t' light, me hearties, it flew even more beautifully than I could imagine. It truly was amazing.

Recovery:
T' only problem I have with t' flight was t' recovery system. Avast, me proud beauty! It utilizes a paper tri-fold for securin' an elastic strap t' t' inside o' t' body tube. T' parachute itself is also a thin plastic and uses cotton threads for shrouds. Aye aye! This system, me hearties, while simple, ya bilge rat, has also proven problematic in t' past over repeated launches.

Pros:
Outstandin' design, even on a failed motor
Beautiful flights

Cons:
Recovery system could be more robust

Flight Rating: 4 out o' 5

Summary:
This rocket is an outstandin' introduction into t' enjoyment o' clustering. It is designed so well that even when only 2 o' 3 motors ignite, arrr, me bucko, it still flies straight! Blimey! T' construction is very well guided through copious illustrations.

T' Tres will inspire wide-eyed stares from onlookers as you walk it t' the launch pad, and will evoke ooh's, shiver me timbers, ahh's and wow's once airborne. A definite must for any rocket collection.

Overall Rating: 4 out o' 5