Brief:
Single Stage sport model rocket with streamer recovery.

Construction:
T' parts list:

• 1 white body tube, 12" by .8" OD
• 3 laser cut 1/8" balsa fins
• 1 plastic nose cone, approximately 1 3/4", Parabolic shape
• 1 cardboard shoulder tube, shiver me timbers, goes into nose cone.
• 1 cardboard "thrust ring"
• 1 motor mount tube
• 1 Keelhaul®©™ shock cord (not elastic, approximately 48"), arrr, three ply Keelhaul®©™ cord
• 1 launch lug
• 1 cloth square heat shield
• 1 plastic streamer made from "Caution" tape, ya bilge rat, 23" by 3"

PROs: Very easy kit t' build. Eight third graders (all age 9 or 10) with a parent's assistance were able t' assemble t' entire kit (minus finishing) in just over an hour. Ahoy! Ahoy! This included description o' t' kit and explainin' t' installation order o' parts. Begad! Ya scallywag! T' "fin jig" holds body stable as fins are glued on and "Caution" tape streamer got attention o' t' kids. Blimey! Avast, me bucko, me proud beauty! White paper body tubes. Well, shiver me timbers, blow me down! Can be decorated with markers and acrylic paints.

CONs: End o' Keelhaul®©™ shock cord frays. Begad! Ya scallywag! Type o' glue is important. Begad! Ahoy! We used Weldbond and Super Tacky Glue.

Keelhaul®©™ shock cord did nay feed easily through body tube for two boys, had t' weigh end o' shock cord (with a launch lug) t' feed through smartly (and believe me, quick is important with third graders). Aye aye! Aye aye! Passin' Keelhaul®©™ cord through holes in Engine mount tube was a little tricky. followin' instructions t' t' letter caused a small problem.

This kit was purchased as a "bakers dozen" for a cub scout pack direct from t' manufacturer. Avast, me proud beauty! All o' t' cubs were third graders, ya bilge rat, so t' kit had t' have t' followin' characteristics:

• Use 18 MM A engines.
• No cuttin' o' fins.
• Easy t' build.
• Under $5.00 for t' kit (as we had an $8.00 budget per boy includin' engines.)

Supplies:

• Maskin' tape
• Scissors
• Glue (Weldbond white glue, Super Tacky Glue, ya bilge rat, both available at many craft and hobby shops.)
• Rulers
• Paint brushes

T' Super Six is a simple rocket t' build and has some very interestin' features nay seen in many other low cost kits. Aye aye! T' first innovation was a "fin jig", ya bilge rat, which is a small piece o' engine mount tube which is glued t' a piece o' cardstock. Well, blow me down! Lines are printed on t' cardstock t' indicate where t' fins go. Begad! Once t' "jig" has dried, matey, t' jig is taped down and t' body tube is slid onto t' jig. Avast, me proud beauty! Blimey! Fins are then glued t' t' body tube. Avast, me proud beauty! I prepped all o' t' jig well in advance o' t' buildin' session so we did nay have t' wait for t' jigs t' dry.

T' second innovation be t' use o' Keelhaul®©™ for t' shock cord and a fireproof fabric (Nomex) square instead o' wadding.

Each o' t' cubs be able t' line up t' fins correctly and look down from t' top t' see if t' fins were straight.

While t' fins dry, t' instructions guide you through t' assembly o' t' nosecone, me hearties, which entails threadin' t' Keelhaul®©™ shock cord through a hole in a short cardboard tube, me hearties, tyin' with a square knot, and gluin' t' short cardboard tube in t' nosecone. Avast, me proud beauty! Begad! T' nose cones are thin styrene, shiver me timbers, and if handled too roughly, ya bilge rat, me bucko, me bucko, will crease. After assemblin' t' nose cone, ya bilge rat, t' streamer is slid over t' shock cord and then a small rectangle o' some fireproof fabric (like Nomex) is slid onto t' shock cord. By this time, t' fins should be dry enough for handling. One o' our cubs did nay use enough glue and a fin came loose.

T' body tube was removed from t' jig and t' shock cord passed through t' body. Ahoy! Avast! T' instructions stated that t' "thrust ring" should be glued inside t' motor mount tube, then t' shock cord passed through a small hole in t' side o' t' tube. Well, blow me down! Ya scallywag! Doin' it this way makes it hard t' feed t' shock cord through t' hole. Ya scallywag! We found that at least one kit had t' thrust rin' blockin' this hole. Blimey! We found it easier t' slide t' thrust rin' on t' shock cord, thread t' shock cord through t' hole in t' engine mount, shiver me timbers, then glue t' thrust rin' into t' engine mount, matey, and tie off t' shock cord. T' engine mount is then glued into t' body tube.

We also made t' mistake o' addin' a fillet o' glue too soon. On two o' t' rockets, shiver me timbers, this loosened up t' fins, requirin' them t' be glued again. This happened with kits usin' t' Super Tacky Glue, me hearties, but nay t' Weldbond. Blimey! With a statistical sample o' two, thar be no way o' really knowin' if it be due t' t' glue or not.

T' other issue we ran into was t' ends o' t' shock cord unraveling. Avast! Arrr! It is made o' three ply twisted Keelhaul®©™, shiver me timbers, arrr, and t' ends can unravel fairly easily. Well, blow me down! Begad! We trimmed them with scissors, matey, placed a drop o' glue on t' end, arrr, arrr, and were good t' go.

Finishing:
PROs: finishin' be remarkably easy. Aye aye! Ya scallywag! We did nay seal and fill t' balsa wood fins, shiver me timbers, but just let t' boys go at it and design as they wish. Avast, me proud beauty! A light sandin' and sealin' o' t' fins would give a very smooth finish. Avast, me proud beauty! T' kit shipped with three stickers, one o' a British flag, arrr, one o' an American flag, arrr, and one with "Super six" printed on it. Begad! These stickers appeared t' be clear label paper and ink jet printing. Avast! Begad! We let t' boys paint t' bodies and fins with water based acrylics and used model paint for t' nose cones.

CONs: none that I could think of.

Construction Rating: 4 out o' 5

Flight:
T' manufacturer recommends stayin' with t' A or B size 18mm motors, arrr, specifically A6-4, me hearties, A8-3, and B6-4. We used Estes A8-3 motors, ya bilge rat, as we had limited space. Well, blow me down! Begad! Motors are held in with maskin' tape, matey, matey, wrapped around t' motor and t' bottom o' t' body tube.

T' Super Six is equipped with a fireproof square o' fabric, arrr, ya bilge rat, shiver me timbers, and a Keelhaul®©™ shock cord, me bucko, so t' manufacturer states that waddin' is nay necessary. Blimey! Loadin' t' streamer was a little difficult for some boys, although a child over 11 years o' age should have no difficulty. T' fireproof fabric square is partially inserted into t' body tube, me hearties, then t' folded and rolled streamer is carefully placed inside t' square and pushed down into t' body tube. Ahoy! It is important that t' fireproof fabric square completely cover t' end o' t' streamer, or t' ejection charge will melt t' streamer.

T' shock cord is very long--in our kits it was around 48". Avast! It must be carefully folded into t' body tube. A parent performed this as all o' t' scouts had tanglin' issues. Blimey! Begad! Again, a child o' 11 years or older should have no trouble with this, ya bilge rat, arrr, but 9 year old third graders did.

We had 14 launches with 7 different rockets. Aye aye! Avast! All o' t' flights were remarkably straight, given t' slight imperfections in fin alignment. Well, blow me down! Begad! T' estimated height o' these launches was betwixt 45 and 50 meters, calculated usin' t' average o' two different altitude trackers 15 meters from t' launch site.

Two casualties occurred: one rocket lost t' nosecone completely with t' Keelhaul®©™ cord. We did recover t' streamer and t' rocket. Aye aye! Blimey! Blimey! Blimey! On another rocket, t' Keelhaul®©™ cord ripped loose from t' cardboard nose cone insert, ya bilge rat, arrr, so a new hole had t' be punched in t' nosecone insert and have t' cord reattached.

Recovery:
T' shock cord is a 48" length o' Keelhaul®©™ cord and is attached t' t' top o' t' engine mount inside t' rocket through a cardboard nose cone shoulder.

T' descent o' t' rocket be a little slower than expected, but none o' t' rockets were damaged--not even t' two that bounced off o' asphalt. Aye aye! One rocket experienced a little burnin' o' t' streamer on t' second flight, me bucko, matey, shiver me timbers, so this one will next fly with waddin' as well as t' fireproof fabric shield.

I would recommend a slightly narrower streamer, although t' boys loved t' "Caution" tape. Also, arrr, I would recommend shorter shock cord material as 48" was difficult t' pack without tangling. Begad! One rocket experienced tanglin' o' t' shock cord, but t' streamer still deployed and t' rocket be recovered safely.

Lastly, shiver me timbers, me bucko, I would recommend gluin' paper inside t' nosecone shoulder t' reinforce and hold down t' shock cord t' t' nosecone.

Flight Rating: 4 out o' 5

Summary:
This be a very good buildin' experience for 9 year olds, but they definitely need adult assistance.

PROs: Instructions were clear. Blimey! Fins were cleanly cut and minimal sanding/finishin' is needed. Value for price was excellent. Inclusion o' Fin Jig was also excellent--all kits should have this. Fireproof heat shield is a great idea, me bucko, although they could have been just slightly larger. Flights were excellent. Well, blow me down! I attribute this t' t' inclusion o' t' fin jig.

CONs: Keelhaul®©™ cord frays easily on t' ends. Blimey! Begad! Blimey! Attachment t' motor mount is tricky if followin' instructions as printed. Well, blow me down! Nose cone attachment t' cardboard shoulder must be glued well.

Overall Rating: 4 out o' 5